ACCTEST.TXT Driver File Contents (en1203_driver.zip)

ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³		 ACCTON TECHNOLOGY CORPORATION			³
³  EN1203, EN1207(-TX) Series NETWORK TESTING PROGRAM (ACCTEST) ³
³			USER GUIDE				³
³								³
³	Copyright 1995-1997 ACCTON Technology Corporation	³
³		      All rights reserved.			³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ

ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»
º		      Release History				º
ÌÍÍÍÍÍÍÍÍÍÍÍÍËÍÍÍÍÍÍÍÍÍËÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͹
º    date    º version º	  description			º
ÌÍÍÍÍÍÍÍÍÍÍÍÍÎÍÍÍÍÍÍÍÍÍÎÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͹
º 11-08-1995 º	v1.00  º  1. New release.			º
º	     º	       º					º
º 12-07-1995 º	v1.01  º  1. Update link stauts check functions º
º	     º	       º					º
º 02-14-1996 º	v1.02  º  1. Backward support EN1203 & EN1207	º
º	     º	       º					º
º 09-04-1996 º	v1.04  º  1. Support New NIC & PHY chip 	º
º	     º	       º					º
º 01-27-1997 º	v1.05  º  1. Support 83840A PHY chip		º
º	     º	       º					º
º 04-08-1997 º	v1.06  º  1. Support EN1207B-Tx 		º
ÈÍÍÍÍÍÍÍÍÍÍÍÍÊÍÍÍÍÍÍÍÍÍÊÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ

1.  The ACCTON PCI Network Adapters Testing Program - ACCTEST

The ACCTON Hardware Driver Disk includes a network testing program
called ACCTEST. Run this program to check if your adapter is properly
installed. The ACCTEST program works for the following PCI LAN
adapters:

	ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
	³   Product Name	    Product Number   ³
	ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
	³ EtherDuo PCI		       EN1203	     ³
	³ Fast EtherCombo-TX PCI       EN1207	     ³
	³ Fast EtherPair-TX PCI        EN1207-TX     ³
	³			    or EN1207B-TX    ³
	ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ


This ACCTEST program performs the following tests on your adapter :

		 a.  Configuration Test
		 b.  I/O Test
		 c.  ID Test
		 d.  Internal Loopback Test
		 e.  External Loopback Test
		 f.  Interrupt Test
		 g.  Network Function Test


2.   Test Requirements

To run ACCTEST, you need at least two workstations, each with an
installed  PCI Fast Ethernet or  any  ACCTON  Ethernet	Adapter.
You  should  run  the  program	in  both workstations, one after
the other.   If you want  to  test  100Mbps  Fastnet  operation,
you  must  have at least two workstations each with an installed
EN1207(-TX) Adapter.


3.   Running the ACCTEST Program

Insert the ACCTON EN1203, EN1207(-TX) Series PCI Network Adapter
Driver Diskette into drive A:, then type:

	 A:\> ACCTEST  <Enter>


----------------------------------------------------------------------

3.0. Each time you enter ACCTEST program, the program first finds out
     all Accton's PCI adapters on your PC.  If your PC does not
     support PCI BIOS, or there is no Accton's PCI adapter on your PC,
     then  the	program  will  show you an error message.  Otherwise,
     ACCTEST  will  display  information  of  all Accton's PCI
     adapters  (at most 4)  on	your  PCI  machine.  Each  adapter's
     information is consisted of adapter no., Ethernet address, IRQ used,
     I/O port used, and a predefined medium type (AUTO or Auto-Negotiation,
     means media-type AUTO-sensing).  You can use UP, DOWN arrow keys to
     select the adapter for testing, or use RIGHT, LEFT arrow keys to select
     the media-type.
     EN1203 PCI Ethernet adapter supports three media-types:

	1. AUTO
	2. TP
	3. BNC;

     while EN1207 PCI Fastnet adapter supports four media-types;
     they are:

	1. AUTO
	2. TP 100Mbps
	3. TP  10Mbps
	4. BNC 10Mbps;

     and EN1207-TX Series has five kinds of medium types:

	  1. Auto Negotiation
	  2. TP  10Mbps
	  3. TP 100Mbps
	  4. TP  10Mbps Full Duplex
	  5. TP 100Mbps Full Duplex

     Finally, you must press ENTER to confirm the selected adapter for
     entering the test procedure, or press ESC to exit the ACCTEST program.


3.1. After you selected an adapter, then Testing Report showing the
     result of each test conducted appears on your screen.  The test
     results are indicated by a 'PASS' or 'FAIL' remark.


3.2. This screen will present you with a Testing Report to indicate the
     result if each test conducted.  The test results will be indicated
     by a 'PASS' or 'FAIL' remark.

There are three functional keys which could be used during execute
ACCTEST.EXE program, they are

	<F1>	To reset all counters which report the real
		network status.

	<F2>	To toggle the network function test ON or OFF.
		It is a toggle switch makes the network function
		test to be in reversed way.

	<ESC>	To terminate and return to the Adapter-Selection Screen.


The real network status report on this ACCTEST.EXE program including
TX count, RX count and two errors CRC and ALG are shown on the
Test Screen.  The Time that is accumulated by this program and
the  Performance which is calculated by this program are also
shown on the Test Screen.


After  you press the <F2> key once, the network function test now is
entering into the 'ON' condition, that is, TX count  is going to
increase quickly (single station).  And if there is more than one
station are running  ACCTEST with network function test 'ON' on your
network system multiple stations), then RX count is also increasing
quickly to reflect the real network traffic.


When any of a diagnosis test results to a 'FAIL' remark, your screen
will change to give you a description of the malfunction and at the
same time also give you some advices to solve that problem.


4.   Test Fail Messages

Possible results and suggested solutions for the diagnostics test
are listed below :

ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍËÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»
º     Test Result    º		 Suggested Solution	    º
ÌÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÎÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͹
º  Configuration     º	1. Check PCI BIOS setup about PCI   º
º  Test Fail	     º	   adapter .			    º
º		     º	2. Contact your dealer or ACCTON    º
º		     º	   Technology Corporation.	    º
ÌÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÎÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͹
º  I/O Test Fail     º	1. Check the parameter with PCI     º
º		     º	   adapter in BIOS setup is correct º
º		     º	   or not.			    º
º		     º	2. Check if you are now running     º
º		     º	   EMM386.EXE.	If your EMM386.EXE  º
º		     º	   has a version earlier than 4.49, º
º		     º	   it can not handle properly	    º
º		     º	   DWORD accesses and may cause     º
º		     º	   the I/O Test to fail.	    º
º		     º	3. Contact your dealer or ACCTON    º
º		     º	   Technology Corporation.	    º
ÌÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÎÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͹
º  ID Test Fail      º	1. ID checksum error.		    º
º		     º	2. Contact your dealer or ACCTON    º
º		     º	   Technology Corporation	    º
ÌÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÎÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͹
º  Internal Loopback º	1. Contact your dealer or ACCTON    º
º  Test Fail	     º	   Technology Corporation.	    º
ÌÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÎÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͹
º  External Loopback º	1. Check your cables, connectors    º
º  Test Fail	     º	   and terminators(Coaxial cables). º
º		     º	2. Check if you have selected the   º
º		     º	   right medium type.		    º
º		     º	3. Check if you are using a cross-  º
º		     º	   over cable, if you use cross-    º
º		     º	   over cable, you may not pass the º
º		     º	   external loopback test, yet you  º
º		     º	   can pass this test just press    º
º		     º	   ENTER key.			    º
º		     º	4. Contact your dealer or ACCTON    º
º		     º	   Technology Corporation.	    º
ÌÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÎÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͹
º  Interrupt Test    º	1. Check IRQ setting in your PCI    º
º	 Fail	     º	   configuration of your computer.  º
º		     º	2. Check your cables, connectors    º
º		     º	   and terminators(Coaxial cables). º
º		     º	3. Check your BIOS configuration    º
º		     º	   Setting, re-setup your	    º
º		     º	   Adapter.			    º
º		     º	4. Contact your dealer or ACCTON    º
º		     º	   Technology Corporation.	    º
ÌÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÎÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͹
º  Network Function  º	1. Check cables, connectors, and    º
º  Test :	     º	   board connections.		    º
º  Receive Test Fail º	2. Re-install the adapter board.    º
º  (Rx packet count  º	3. Reset the stations and run the   º
º   not running)     º	   ACCTEST program in various	    º
º		     º	   sequence to decide which	    º
º		     º	   adapter board is defective.	    º
º		     º	4. Contact your dealer or ACCTON    º
º		     º	   Technology Corporation.	    º
ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÊÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ

--- End of File ---

Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web3, load: 0.72