; PT_900.INI [settings] ;************************************************************************** ; Devmode Overrides ; These only override the initial default values ; Once the driver is initialized these values will then have no effect ; Cartridge Type default ; possible values: ; 0 = 1-Color; 1 = 3-Color; 2 = 4-Color CartridgeType = 2 ; Resolution default ; 0 = Quality 1 (1-pass Draft); 1 = Quality 2 (2-pass); 2 = Quality 3 (4-pass); 3 = Quality 4 (8-pass) Resolution = 1 ; Saturation default ; 0 to 100 possible ;Saturation = 100 **************************************************************************** ; BLOOM COMPENSATION ; #Black pixels to remove (improves barcode scanning) ; For best speed/quality may want to set to 0 if not scanning barcodes BloomComp = 1 ; Status Monitor will warn user of "Low Ink" at Start of Job ; IF % remaining ink is less than this value InkLowPercent = 20 InkVeryLowPercent = 10 ; Override values for left and top offset, default values ; are TopMarginOffset=0, and LeftMarginOffset = 0 TopMarginOffset = 0 LeftMarginOffset = 0 ;Media and Quality Overrides, the following values are accepted ; Media: 1= MT_PLAIN,2=MT_COATED,3=MT_GLOSSY, 4=MT_TRANSPARENCY, ; 5=MT_IRON_ON_TRANSFER,6=MT_GREETING_CARD,7=MT_GLOSSY1,8=MT_GLOSSY2,9=MT_GLOSSY3, ; Quality: 1= PQ_QUICK_PRINT,2=PQ_NORMAL,3=PQ_BETTER, 4=PQ_BEST,5=PQ_AUTOMATIC MediaType_Quality1_K = 1 PrintQuality_Quality1_K = 1 MediaType_Quality1_CMY = 1 PrintQuality_Quality1_CMY = 1 MediaType_Quality1_CMYK = 1 PrintQuality_Quality1_CMYK = 1 MediaType_Quality2_K = 1 PrintQuality_Quality2_K = 2 MediaType_Quality2_CMY = 1 PrintQuality_Quality2_CMY = 2 MediaType_Quality2_CMYK = 1 PrintQuality_Quality2_CMYK = 2 MediaType_Quality3_K = 1 PrintQuality_Quality3_K = 4 MediaType_Quality3_CMY = 1 PrintQuality_Quality3_CMY = 4 MediaType_Quality3_CMYK = 2 PrintQuality_Quality3_CMYK = 2 MediaType_Quality4_K = 5 PrintQuality_Quality4_K = 4 MediaType_Quality4_CMY = 3 PrintQuality_Quality4_CMY = 4 MediaType_Quality4_CMYK = 2 PrintQuality_Quality4_CMYK = 4 ; DEBUGGING ; ; ***NOTE: for debugging to work with the "_u" driver you must also place this .INI file at C:\ ; ; turn debugging ON (1) or OFF (0) -- default is OFF if not specified DebugOn = 1 ; AMOUNT OF DEBUG INFO ; LEVEL = 0 through 6 (lower numbers give more debug info) ; 0 = DBGLVL_ZERO ; 1 = DBGLVL_TRACE ; 2 = DBGLVL_DUMP ; 3 = DBGLVL_INFORM (default if not specified) ; 4 = DBGLVL_WARNING ; 5 = DBGLVL_ERROR ; 6 = DBGLVL_FATAL DebugThreshold = 3 ; Amount of image sharpening ; 0 = off ; 1-10 = increasing sharpening levels ; 11 = automatic ; 12 = off SharpenLevel = 11 ; Bypass the alignment required warning? ; 0 = don't bypass the warning (DEFAULT) 1= bypass the warning ; NOTES: ; 1. This only works if cartridge setting is set to Color only or Black only ; 2. USE AT YOUR OWN RISK - BYPASSING ALIGNMENT MAY NOT PROVIDE OPTIMUM PRINT QUALITY ; (for best print quality you should align after changing cartridges). ; 3. The warning will still show up after changing the cartridge, but you can Cancel. The warning will not be given when printing. BypassAlignWarning=0 ; Set this value to non-zero to allow printing on a plain paper sheet ; This will allow the loop sensor to be ignored ; You must remove the label stock and then send a print. The printer will allow you to feed in a sheet of paper. ; For normal label stock printing this value must be set to zero. PaperSheet = 0 ; Number of passes override for Quality 1-4 ; NumPasses can be: 1,2,4,8,16 NumPasses_1=1 NumPasses_2=2 NumPasses_3=4 NumPasses_4=8 ; Carrier Speed Override for Quality 1-4 ; Override print carrier speed (in inches per second) ;CarrierSpeed_1 = 30 ;CarrierSpeed_2 = 30 ;CarrierSpeed_3 = 30 ;CarrierSpeed_4 = 30 ; Print Direction Override ; This overrides print direction (when driver is not set to Bidi) ; PrintDirectionOverride1 is for cartridge 1 and PrintDirectionOverride2 is for cartridge 2 ; = 1 = LTOR ; = 2 = RTOL PrintDirectionOverride1 = 2 PrintDirectionOverride2 = 2 ; IgnoreDirection ; If set to 1, the print direction will not be specified IgnoreDirection=0 ; Write output to FILE in addition to sending to the printer? ; Comment this line out for no PRN to be saved ; Or, set it to the filename (including path) you want to save ;PRN_TO_SAVE=c:\900_Output.prn ; Send Print Setup Command ; 1=yes 0=no PrintSetupCmd=1 ; Delay (in msec) before sending final Print Complete Command ; NOTE: cannot cut too short or printing will not finish DelayBeforeFinalCmd=10 ; How often to send status update to status monitor ; After this Number of Packets sent (1 to 4000000000) StatusFrequency = 50 ; How long to wait to attempt to get a communications pipe to the ; status monitor (in mSec) when a job is launched. PipeRetryTime = 15000 ; How long to wait (in mSec) before starting to print again after end of roll error and loading in new roll ; If set too low then top of form will not work correctly (may need to increase this for large label sizes) EndOfRollInJobDelay = 10000 ; Wait for Idle at End Doc before sending Done Printing Command? ; 0=no (default) 1=yes WAIT_FOR_IDLE_END_DOC = 0; ; Delay (in mSec) between sending messages to Status Monitor ; Default = 0 DELAY_BETWEEN_MESSAGES = 0 ;*************************************** ; RFID Enabled Printer? ; 1 = yes 0 = no RFID_ENABLED = 1 ;*************************************** ; Print Reject when RFID fails to program ; 1 = yes (default), 0 = no PRINT_REJECT=1 ; Delay after sending print before checking for busy WAIT_FOR_BUSY_DELAY = 2000 ; mSec to delay before/after sending request before retrieving data from RFID module ; setting too short may cause data to not be ready RFID_READ_DELAY1 = 100 RFID_READ_DELAY2 = 20 ; This is how many times it will try to read/write/verify a tag RFID_ATTEMPTS=5 ; -RFID SIMULATION- ; 1=SIMULATE RFID MODULE (0=do NOT simulate) RFID_SIMULATE=0 ; SIMULATE_SUCCESS: 1=success (note: only has effect if NUMTAGS=1) RFID_SIMULATE_SUCCESS=1 ; NUMTAGS: 0=no tags found, 1=found correct number, 2=too many tags found RFID_SIMULATE_NUMTAGS=1 RFID_HUNT_POSITION=1 RFID_HUNT_ATTEMPTS=4 RFID_HUNT_POSITION_STEP_SIZE=60 ; Do NOT change this - for debugging ONLY ; Set to 1 it will keep trying to read tags and will keep reporting back zero found CALIBRATE_MODE = 0Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.