Chapter 2 Commands (CH$ means the ch number) (NOTE:HARM is possible set up only with 8807-51,8808-51) 2.1 Command Summary 2.1.1 Standard Commands Specified by IEEE 488.2 --------------------------------------------------------------------------- Command | Data | Explanation | (for a query, response data) | --------------------------------------------------------------------------- *CLS | | Clears the status byte | | and associated queues. --------------------------------------------------------------------------- *ESR? | A <NR1> : 0 to 255 | Queries SESR. --------------------------------------------------------------------------- IDN? | Maker's name, model number | | serial number(not used, 0) | Queries device ID. | software version | --------------------------------------------------------------------------- *OPC | | Sets the LSB of SESR after | | all action has been | | completed. --------------------------------------------------------------------------- *OPC? | A <NR1> | ASCII 1 is the response | | after all action has been | | completed. --------------------------------------------------------------------------- *OPT? | ch1,ch2,ch3,ch4,A | Queries device option | A:printer unit | provision. | 0: none, 1: exist | --------------------------------------------------------------------------- *RST | | Device initial setting. --------------------------------------------------------------------------- *STB? | A <NR1> : 0 to 255 | Reads the STB and the MSS | | bit, without performing | | serial polling. --------------------------------------------------------------------------- *TST? | A <NR1> : 0=OK, 1=NG | Queries the result of | | the ROM/RAM check. --------------------------------------------------------------------------- *WAI | | Executes the following | | command after action has | | been completed. --------------------------------------------------------------------------- :ESR0? | A <NR1> : 0 to 255 | Queries ESR0. --------------------------------------------------------------------------- 2.1.2 Specific Commands (1)Execution control etc. (common to all functions) --------------------------------------------------------------------------- Command | Data | Explanation | (for a query, response data) | --------------------------------------------------------------------------- :ABORT | | Forced halt. --------------------------------------------------------------------------- :AUTO | | Sets the time axis and | | the voltage axis | | automatically. | | (only memory recorder | | function.) --------------------------------------------------------------------------- :CERRor? | A, B, C :<NR1> | Queries the communication | (number of times) | errors. | A: parity error | | B: overrun error | | C: framing error | --------------------------------------------------------------------------- :ERRor? | A <NR1> : error number | Queries error number. --------------------------------------------------------------------------- :FEED A | A: 1 to 255 (unit mm) | Feeds the paper the | | specified distance. -------------------------------------------------------------------------- :FUNCtion A$ | A$: MEM, REC, RMS, HARM | Changes the function. --------------------------------------------------------------------------- :FUNCtion? | A$ | Queries the function. --------------------------------------------------------------------------- :HCOPy | | Same as the COPY key. --------------------------------------------------------------------------- :HEADer A$ | A$: OFF, ON | Enables and disables | | headers. --------------------------------------------------------------------------- :HEADer? | A$ | Queries headers. --------------------------------------------------------------------------- :PRINt | | Same as the PRINT key. --------------------------------------------------------------------------- :STARt | | Same as the START key. --------------------------------------------------------------------------- :STOP | | Same as the STOP key. --------------------------------------------------------------------------- Command | Data | Explanation | (for a query, response data) | --------------------------------------------------------------------------- (2)CONFigure command (Setting and querying the time axis range, the recording length, etc.) :CONFigure --------------------------------------------------------------------------- Command | Data | Explanation | Function | (for a query, | | | response data) | | --------------------------------------------------------------------------- :ATPRint A$ | A$: OFF, ON | Enables and disables | MEM,HARM | | auto print. | --------------------------------------------------------------------------- :ATPRint? | A$ | Queries auto print | | | enablement. | --------------------------------------------------------------------------- :ATSAve | A$:OFF,ON | Sets auto save. | ALL A$(,B$(,"C$")) | B$:Bin,Text | | | C$:File Name | | | (up to 8 Characters) | | --------------------------------------------------------------------------- :ATSAve? | A$(,B$,"C$") | Queries auto save. | ALL --------------------------------------------------------------------------- :ATARea A$ | A$:ALL,A_B | Sets auto save range. | ALL --------------------------------------------------------------------------- :ATARea? | A$ | Queries | --------------------------------------------------------------------------- :ENDBlock A | A: 1 to number of | Sets the end block | MEM,RMS | blocks | (during sequential | | | save) | --------------------------------------------------------------------------- :ENDBlock? | A <NR1> | Queries the end block.| MEM,RMS --------------------------------------------------------------------------- :FORMat A$ | A$: SINGle, DUAL, | Sets the display | ALL | QUAD, XYDot, XYLine | format. | --------------------------------------------------------------------------- :FORMat? | A$ | Queries the display | MEM,REC,RMS | | format. | --------------------------------------------------------------------------- :FREQuency A | A: 50, 60 (Hz) | Sets the frequency. | RMS --------------------------------------------------------------------------- :FREQuency? | A <NR1> | Queries the frequency.| RMS --------------------------------------------------------------------------- :HANAlyze A$ | A$:WAVE,RMS,RMS-RATIO,| Sets HARM-INSTANT- | HARM | PHASE,POWER, | analyze | | P-RATIO,P-PHASE | | --------------------------------------------------------------------------- :HANAlyze? | A$ | Queries HARM-INSTANT- | HARM | | analyse | --------------------------------------------------------------------------- :HCHAN A$ | A$:CH1,CH2,CH3,CH4 | Sets HARM-INSTANT- | HARM | | channel | --------------------------------------------------------------------------- :HCHAN? | A$ | Queries HARM-INSTANT- | HARM | | channel | --------------------------------------------------------------------------- :HDISP A$ | A$:VALUE,GRAPH | Sets HARM-INSTANT- | HARM | | disp kind | --------------------------------------------------------------------------- :HDISP? | A$ | Queries HARM-INSTANT- | HARM | | disp kind | --------------------------------------------------------------------------- :HFREQuency A$ | A$:AUTO,50,60, | Sets HARM-frequency | HARM | 45.0 to 65.0 | | --------------------------------------------------------------------------- :HFREQuency? | A$ | Queries HARM-frequency| HARM --------------------------------------------------------------------------- :HMODE A$ | A$:INSTANT,SERIES | Sets HARM-mode | HARM --------------------------------------------------------------------------- :HMODE? | A$ | Queries HARM-mode | --------------------------------------------------------------------------- :HPRCHan ch$,A$ | A$:OFF,ON | Sets HARM-INSTANT- | HARM | | print channel | --------------------------------------------------------------------------- :HPRCHan? ch$ | ch$,A$ | Queries HARM-INSTANT- | HARM | | print channel | --------------------------------------------------------------------------- :SANAlyze NO$,A$| NO$:NO1 to NO20 | Sets HARM-SERIES-analyze | HARM | A$:OFF,RMS,RATIO,PHASE, | | | T-RMS,THD-F,THD-R, | | | POWER,P-RATIO,P-PHASE, | | | WATT,VA,VAR,P-FACTOR | | --------------------------------------------------------------------------- :SANAlyze? NO$ | NO$,A$ | Queries HARM-SERIES- | HARM | | analyze | --------------------------------------------------------------------------- :SCHAN NO$,A$ | NO$:NO1 to NO20 | Sets HARM-SERIES- | HARM | A$:CH1,CH2,CH3,CH4 | channel | --------------------------------------------------------------------------- :SCHAN? NO$ | NO$,A$ | Queries HARM-SERIES- | HARM | | channel | --------------------------------------------------------------------------- :SDEGRee NO$,A | NO$:NO1 to NO20 | Sets HARM-SERIES- | HARM | A:1 to 40 | number | --------------------------------------------------------------------------- :SDEGRee? NO$ | NO$,A<NR1> | Queries HARM-SERIES- | HARM | | number | --------------------------------------------------------------------------- :SLOGGing A | A:1 to 1600 | Sets HARM-SERIES- | HARM | | logging output | | | interval | --------------------------------------------------------------------------- :SLOGGing? | A<NR2> | Queries HARM-SERIES- | HARM | | logging output | | | interval | --------------------------------------------------------------------------- :SPRKInd A$ | A$:WAVE,LOGGing, | Sets HARM-SERIES- | HARM | CALC,WAVE&CALC | print mode | --------------------------------------------------------------------------- :SPRKInd? | A$ | Queries HARM-SERIES- | HARM | | print mode | --------------------------------------------------------------------------- :SRESult W$,A | W$:W1 to W4 | Sets HARM-SERIES- | HARM | A:0(OFF),1 to 20 | display | --------------------------------------------------------------------------- :SRESult? W$ | W$,A<NR1> | Queries HARM-SERIES- | HARM | | display | --------------------------------------------------------------------------- :SSHOT A | A:SHOT(unit hour) | Sets HARM-SERIES-shot | HARM --------------------------------------------------------------------------- :SSHOT? | A<NR1>(unit hour) | Queries HARM-SERIES- | HARM | | shot | --------------------------------------------------------------------------- :SSMOOth A$ | A$:OFF,ON | Sets HARM-SERIES- | HARM | | smoothing | --------------------------------------------------------------------------- :SSMOOth? | A$ | Queries HARM-SERIES- | HARM | | smoothing | --------------------------------------------------------------------------- :STIME A | A:TIME/DIVunit hour) | Sets HARM-SERIES-time | HARM --------------------------------------------------------------------------- :STIME? | A<NR3>(unit hour) | Queries HARM-SERIES- | HARM | | time | --------------------------------------------------------------------------- :LOGGing A | A: 1 to 8000 | Specifies the logging | MEM,REC,RMS | | output interval. | --------------------------------------------------------------------------- :LOGGing? | A <NR2> | Queries the logging | MEM,REC,RMS | | output interval. | --------------------------------------------------------------------------- :MAXBlock A | A:2,4,8,16,32 | Sets the number of | MEM,RMS | | memory blocks | | | (during sequential | | | save) | --------------------------------------------------------------------------- :MAXBlock? | A : <NR1> | Queries the number of | MEM,RMS | | memory blocks | --------------------------------------------------------------------------- :MEMDiv A$ | A$: OFF, ON | Sets memory | MEM,RMS | | segmentation. | --------------------------------------------------------------------------- :MEMDiv? | A$ | Queries memory | MEM,RMS | | segmentation. | --------------------------------------------------------------------------- :MEMRec A$ | A$:OFF,ON | Sets the Instantaneous| RMS | | Waveform Recording. | --------------------------------------------------------------------------- :MEMRec? | A$ | Queries the | RMS | | Instantaneous Waveform| | | Recording. | --------------------------------------------------------------------------- :PRINt A$ | A$: OFF, ON | Sets printer output. | REC,RMS,HARM --------------------------------------------------------------------------- :PRINt? | A$ | Queries printer output.| REC,RMS,HARM --------------------------------------------------------------------------- :PRKInd A$ | A$: WAVE,LOGGing | Specifiles the print | MEM,REC,RMS | | mode. | --------------------------------------------------------------------------- :PRKInd? | A$ | Queries the print mode.| MEM,REC,RMS --------------------------------------------------------------------------- :ROLL A$ | A$: OFF, ON | Enables and disables | MEM | | roll mode. | --------------------------------------------------------------------------- :ROLL? | A$ | Queries roll mode | MEM | | enablement. | --------------------------------------------------------------------------- :SEQDisp A$ | A$: OFF, ON | Sets the follow-up | MEM | | waveform display | | | (during sequential | | | save). | --------------------------------------------------------------------------- :SEQDisp? | A$ | Queries the follow-up | MEM | | waveform display. | --------------------------------------------------------------------------- :SHOT A | A: recording length | Sets the recording | ALL | | length (during memory | | (unit DIV) | segmentation) | --------------------------------------------------------------------------- :SHOT? | A <NR1> (unit DIV) | Queries the recording | ALL | | length. | --------------------------------------------------------------------------- :SMOOth A$ | A$:OFF, ON | Sets the smooth | MEM | | printing. | --------------------------------------------------------------------------- :SMOOth? | A$ | Queries smooth| MEM | | | printing enablement. | --------------------------------------------------------------------------- :STTBlock A | A: 1 to number of | Sets the start block | MEM | blocks | (during sequential save)| | | save) | --------------------------------------------------------------------------- :STTBlock? | A : <NR1> | Queries the start block.| MEM --------------------------------------------------------------------------- :TDIV A | A: TIME/DIV | Sets the time axis | ALL | (unit seconds) | range. | --------------------------------------------------------------------------- :TDIV? | A <NR3> (unit seconds)| Queries the time axis | ALL | | range. | --------------------------------------------------------------------------- :THINout A$ | A$:OFF, | Sets the degree of | MEM,REC,RMS | 1_2,1_4,1_8,1_20, | thinning | | 1_40,1_80,1_200, | before storing. | | 1_400,1_800 | | --------------------------------------------------------------------------- :THINout? | A$ | Queries the degree of | MEM,REC,RMS | | thinning before storing.| --------------------------------------------------------------------------- :USEBlock A | A: 1 to number of | Sets the memory block | MEM | segmentations | used. | | (32 max.) | | --------------------------------------------------------------------------- :USEBlock? | A : <NR1> | Queries the memory | MEM | | block used. | --------------------------------------------------------------------------- Command | Data | Explanation | Function | (for a query, | | | response data) | | --------------------------------------------------------------------------- (3)TRIGger command (Setting and querying trigger.) :TRIGger --------------------------------------------------------------------------- Command | Data | Explanation | Function | (for a query, | | | response data) | | --------------------------------------------------------------------------- :DETECTDate | year: 0 to 99 | Sets the date for | ALL year,month, | month: 1 to 12 | trigger detection. | day | day: 1 to 31 | | --------------------------------------------------------------------------- :DETECTDate? | year, month, day | Queries the currently | ALL | all <NR1> | set date for trigger | | | detection. | --------------------------------------------------------------------------- :DETECTTime | hour: 0 to 23 | Sets the time point | ALL hour, min, | min: 0 to 59 | for trigger detection.| sec | sec: 0 to 59 | | --------------------------------------------------------------------------- :DETECTTime? | hour, min, sec | Queries the currently | ALL | all <NR1> | set time point for | | | trigger detection. | --------------------------------------------------------------------------- :EXTErnal A$ | A$: OFF, ON | Enables and disables | ALL | | external trigger. | --------------------------------------------------------------------------- :EXTErnal? | A$ | Queries external | ALL | | trigger enablement. | --------------------------------------------------------------------------- :FILTer ch$, A | A:0(OFF),0.1, 0.2, 0.5| Sets trigger filter. | MEM,REC | 1.0, 1.5, 2, 2.5, 5.0| | | 10.0(DIV)(MEM) | | | A:0(OFF), 1(ON) (REC) | | --------------------------------------------------------------------------- :FILTer? ch$ | ch$, A <NR2> | Queries trigger filter.| MEM,REC --------------------------------------------------------------------------- :HCHAN NO$,A$ | NO$:NO1 to NO4, | Sets HARM-trigger | HARM | A$:CH1 to CH4 | channel | --------------------------------------------------------------------------- :HCHAN? NO$ | NO$,A$ | Queries HARM-trigger | HARM | | channel | --------------------------------------------------------------------------- :HDEGRee NO$,A | NO$:NO1 to NO4, | Sets HARM-trigger | HARM | A:1 to 40 | number | --------------------------------------------------------------------------- :HDEGRee? NO$ | NO$,A<NR1> | Queries HARM-trigger | HARM | | number | --------------------------------------------------------------------------- :HINOUT NO$,A$ | NO$:NO1 to NO4, | Sets HARM-trigger | HARM | A$:IN,OUT | input/output | --------------------------------------------------------------------------- :HINOUT? NO$ | NO$,A$ | Queries HARM-trigger | HARM | | input/output | --------------------------------------------------------------------------- :HKINd NO$,A$ | NO$:NO1 to NO4, | Sets HARM-trigger | HARM | A$:OFF,RMS,RATIO, | kind | | T-RMS,THD-F,THD-R, | | | POWER,P-RATIO, | | | P-PHASE | | --------------------------------------------------------------------------- :HKINd? NO$ | NO$,A$ | Queries HARM-trigger | HARM | | kind | --------------------------------------------------------------------------- :HLEVEl NO$,A | NO$:NO1 to NO4, | Sets HARM-trigger | HARM | A:trigger level | level | | (unit V) | | --------------------------------------------------------------------------- :HLEVEl? NO$ | NO$,A<NR3> | Queries HARM-trigger | HARM | | level | --------------------------------------------------------------------------- :HMODE A$ | A$:SINGle,REPEat | Sets HARM-trigger | HARM | | mode | --------------------------------------------------------------------------- :HMODE? | A$ | Queries HARM-trigger | HARM | | mode | --------------------------------------------------------------------------- :HPRETrig A | A:0,5,10(unit DIV) | Sets HARM-pre trigger | HARM --------------------------------------------------------------------------- :HPRETrig? | A<NR1>(unit DIV) | Queries HARM- | HARM | | pre trigger | --------------------------------------------------------------------------- :HSLOpe NO$,A$ | NO$:NO1 to NO4, | Sets HARM-trigger | HARM | A$:UP,DOWN | direction (slope) | | | (level trigger) | --------------------------------------------------------------------------- :HSLOpe? NO$ | NO$,A$ | Queries HARM-trigger | HARM | | direction | --------------------------------------------------------------------------- :JKINd ch$,A$ | A$:SIN50,SIN60, | Sets the kind of | MEM | PRE50,PRE60 | waveform detection | | | trigger. | --------------------------------------------------------------------------- :JKINd? ch$ | ch$,A$ | Queries the kinds of | MEM | | waveform detection | | | trigger. | --------------------------------------------------------------------------- :JVOLt ch$,A | A:Standard voltage | Sets the standard | MEM | (uint Vrms) | voltage of waveform | | | detection trigger. | --------------------------------------------------------------------------- :JVOLt? ch$ | ch$,A<NR3> | Queries the standard | MEM | | voltage of waveform | | | detection trigger. | --------------------------------------------------------------------------- :JWIDth ch$,A | A:control range | Sets the contorl | MEM | (unit V) | range of waveform | | | detection trigger. | --------------------------------------------------------------------------- :JWIDth? ch$ | ch$,A<NR3> | Queries the contorl | MEM | | range of waveform | | | detection trigger. | --------------------------------------------------------------------------- :KIND ch$, A$ | A$:OFF,LEVEl,IN,OUT, | Sets type of trigger. | MEM,REC,RMS | DROP,JUDGE (MEM) | | | A$:OFF,LEVEl,IN,OUT | | | (REC,RMS) | | --------------------------------------------------------------------------- :KIND? ch$ | ch$, A$ | Queries type of trigger.| MEM,REC,RMS --------------------------------------------------------------------------- :LEVEl ch$, A | A: trigger level | Sets the trigger level| MEM,REC | (unit V) | of the level trigger. | --------------------------------------------------------------------------- :LEVEl? ch$ | ch$, A <NR3> | Queries the trigger | MEM,REC | | level of the level | | | trigger. | --------------------------------------------------------------------------- :LOGAnd ch$, A$ | A$: OFF, OR, AND | Sets AND/OR for the | MEM,REC, | | logic trigger pattern.| RMS --------------------------------------------------------------------------- :LOGAnd? ch$ | ch$, A$ | Queries AND/OR for the| MEM,REC, | | logic trigger pattern.| RMS --------------------------------------------------------------------------- :LOGPat ch$, | A$: xxxx trigger | Sets the pattern for | MEM,REC, 'A$' | pattern (x, 0, 1) | a logic trigger. | RMS --------------------------------------------------------------------------- :LOGPat? ch$ | ch$, "A$" | Queries the pattern | MEM,REC, | | for a logic trigger. | RMS --------------------------------------------------------------------------- :LFILter ch$, A | A:0(OFF), 0.1, 0.2, | Sets logic trigger | MEM,REC, | 0.5, 1.0, 1.5, 2.0, | filter. | RMS | 2.5, 5.0, 10 | | --------------------------------------------------------------------------- :LFILter? ch$ | ch$, A <NR2> | Queries logic trigger | MEM,REC, | | filter. | RMS --------------------------------------------------------------------------- :LOWEr ch$, A | A: lower limit level | Sets lower limit level| MEM,REC | (unit V) | of window-in/-out | RMS | | trigger. | ---------------------------------------------------------------------------- :LOWEr? ch$ | ch$, A <NR3> | Queries lower limit | MEM,REC | | level of window-in/-out| | | trigger. | ---------------------------------------------------------------------------- :MANU A$ | A$: OFF, ON | Sets manual trigger. | ALL ---------------------------------------------------------------------------- :MANU? | A$ | Queries manual trigger.| ALL ---------------------------------------------------------------------------- :MODE A$ | A$:SINGle,REPEat, | Sets trigger mode. | MEM,REC,RMS | AUTO(MEM) | | | SINGle,REPEat | | | (REC,RMS) | | ---------------------------------------------------------------------------- :MODE? | A$ | Queries trigger mode. | MEM,REC,RMS ---------------------------------------------------------------------------- :PRETrig A | A:0,2,10,¥¥90,95,100, | Sets pre-trigger. | MEM,RMS | -95% (MEM) | | | 0,5,10DIV(RMS) | | ---------------------------------------------------------------------------- :PRETrig? | A <NR1> (unit %) | Queries pre-trigger. | MEM,RMS ---------------------------------------------------------------------------- :RLEVel ch$, A | A: trigger level (V) | Sets the trigger level| RMS | | of RMS level trigger. | ---------------------------------------------------------------------------- :RLEVel? ch$ | ch$, A <NR3> | Queries the trigger | RMS | | level of RMS level | | | trigger. | ---------------------------------------------------------------------------- :RSLOpe ch$, A$ | A$: UP, DOWN | Sets the direction | RMS | | (slope) of RMS level | | | trigger. | ---------------------------------------------------------------------------- :RSLOpe? ch$ | ch$, A$ | Queries the direction | RMS | | (slope) of RMS level | | | trigger. | ---------------------------------------------------------------------------- :SLOPe ch$, A$ | A$: UP, DOWN | Sets the trigger | MEM,REC | | direction (slope) | | | (level trigger). | ---------------------------------------------------------------------------- :SLOPe? ch$ | ch$, A$ | Queries the trigger | MEM,REC | | direction (slope). | ---------------------------------------------------------------------------- :SOURce A$ | A$:OR,AND | Sets trigger logical | ALL | | operator to AND or OR.| ---------------------------------------------------------------------------- :SOURce? | A$ | Queries trigger logical| ALL | | operator (AND or OR). | ---------------------------------------------------------------------------- :STOPDate | year: 0 to 99 | Sets the date for | REC year,month, | month: 1 to 12 | termination. | day | day: 1 to 31 | | ---------------------------------------------------------------------------- :STOPDate? | year, month, day | Queries the date of | REC | all <NR1> | termination. | ---------------------------------------------------------------------------- :STOPTime | hour: 0 to 23 | Sets the termination | REC hour,min, | min: 0 to 59 |time of operation. | sec | sec: 0 to 59 | | ---------------------------------------------------------------------------- :STOPTime? | hour, min, sec | Queries the termination| REC | all <NR1> | time of operation. | ---------------------------------------------------------------------------- :TIMEr A$ | A$: OFF, ON | Sets timer trigger. | ALL ---------------------------------------------------------------------------- :TIMEr? | A$ | Queries timer trigger.| ALL ---------------------------------------------------------------------------- :TIMIng A$ | A$:START,STOP,S_S | Sets trigger timing. | REC ---------------------------------------------------------------------------- :TIMIng? | A$ | Queries trigger timing.| REC ---------------------------------------------------------------------------- :TMINTvl | day: 0 to 99 | Sets time interval for| ALL day, hour, | hour: 0 to 23 | timer trigger. | min, sec | min: 0 to 59 | | | sec: 0 to 59 | | ---------------------------------------------------------------------------- :TMINTvl? | day, hour, min, sec | Queries time interval | ALL | all <NR1> | for timer trigger. | ---------------------------------------------------------------------------- :TMSTArt | month: 1 to 12 | Sets start time of | ALL month, day, | day: 1 to 31 | timer trigger. | hour, min | hour: 0 to 23 | | | min: 0 to 59 | | ---------------------------------------------------------------------------- :TMSTArt? | month, day, hour, min | Queries start time of | ALL | all <NR1> | timer trigger. | ---------------------------------------------------------------------------- :TMSTOp | Same as :TMSTArt | Sets stop time of | ALL month, day, | | timer trigger. | hour, min | | | ---------------------------------------------------------------------------- :TMSTOp? | Same as :TMSTArt? | Queries stop time of | ALL | | timer trigger. | ---------------------------------------------------------------------------- :UPPEr ch$, A | A: upper limit level | Sets upper limit level| MEM,REC | (unit V) | of window-in/-out | | | trigger. | ---------------------------------------------------------------------------- :UPPEr? ch$ | ch$, A <NR3> | Queries upper limit | MEM,REC | | level of window-in | | | /-out trigger. | ---------------------------------------------------------------------------- :VFREq ch$, A | A: 50/60 (Hz) | Sets measurement | MEM | | frequency of voltage | | | drop trigger. | ---------------------------------------------------------------------------- :VFREq? ch$ | ch$, A <NR1> | Queries measurement | MEM | | frequency of voltage | | | drop trigger. | ---------------------------------------------------------------------------- :VLEVel ch$, A | A: drop level (V) | Sets drop level of | MEM | | voltage drop trigger. | ---------------------------------------------------------------------------- :VLEVel? ch$ | ch$,A<NR3> | Queries drop level of | MEM | | voltage drop trigger. | ---------------------------------------------------------------------------- Command | Data | Explanation | Function | (for a query, | | | response data) | | ---------------------------------------------------------------------------- (4)UNIT command (Setting and querying input channel) :UNIT ----------------------------------------------------------------------------- Command | Data | Explanation | Function | (for a query, | | | response data) | | ----------------------------------------------------------------------------- :COUPling ch$, | A$: GND, DC, CLAMp | Sets input channel | MEM,REC,RMS A$ | | coupling. | ----------------------------------------------------------------------------- :COUPling? ch$ | ch$, A$ | Queries input channel | MEM,REC,RMS | | coupling. | ----------------------------------------------------------------------------- :FILTer ch$, A | A: 0 (OFF), 5, 500 | Sets input channel | MEM,REC,RMS | | filter. | ----------------------------------------------------------------------------- :FILTer? ch$ | ch$, A$ | Queries input channel | MEM,REC,RMS | | filter. | ----------------------------------------------------------------------------- :HINPut ch$,A$ | A$:VOLT,9018,9132, | Sets HARM-input kind | HARM | 3283,3284,3285,9322| | ----------------------------------------------------------------------------- :HINPut? ch$ | ch$,A$ | Queries HARM-input | HARM | | kind | ----------------------------------------------------------------------------- :HRANGe ch$,A | A:volt(current)range | Sets HARM-input | HARM | (unit Vr,Ar) | channel voltage or | | | current axis range | ----------------------------------------------------------------------------- :HRANGe? ch$ | ch$,A<NR3> | Queries HARM-input | HARM | (unit Vr,Ar) | channel voltage or | | | current axis range | ----------------------------------------------------------------------------- :HSCALing ch$,A$| A$:OFF,ON | Sets HARM-scaling | HARM ----------------------------------------------------------------------------- :HSCALing? ch$ | ch$,A$ | Queries HARM-scaling | HARM ----------------------------------------------------------------------------- :HSCVSet ch$,A$ | A$:PT,A | Sets HARM-scaling | HARM | | kind | ----------------------------------------------------------------------------- :HSCVSet? ch$ | ch$,A$ | Queries HARM-scaling | HARM | | kind | ----------------------------------------------------------------------------- :HSCCT ch$,A | A:0.01 to 99999.00 | Sets HARM-scaling | HARM | | ct ratio | ----------------------------------------------------------------------------- :HSCCT? ch$ | ch$,A<NR3> | Queries HARM-scaling | HARM | | ct ratio | ----------------------------------------------------------------------------- :HSCPT ch$,A | A:0.01 to 99999.00 | Sets HARM-scaling | HARM | | pt ratio | ----------------------------------------------------------------------------- :HSCPT? ch$ | ch$,A<NR3> | Queries HARM-scaling | HARM | | pt ratio | ----------------------------------------------------------------------------- :HSCVOlt ch$,A | A:0.01 to 99999.00 | Sets HARM-scaling | HARM | | volt | ----------------------------------------------------------------------------- :HSCVOlt? ch$ | ch$,A<NR3> | Queries HARM-scaling | HARM | | volt | ----------------------------------------------------------------------------- :HSCAMp ch$,A | A:0.01 to 99999.00 | Sets HARM-scaling | HARM | | amp | ----------------------------------------------------------------------------- :HSCAMp? ch$ | ch$,A<NR3> | Queries HARM-scaling | HARM | | amp | ----------------------------------------------------------------------------- :HWIRing A$ | A$:UNIQ,1P2W,1P3W,3P3W| Sets HARM-wiring | HARM ----------------------------------------------------------------------------- :HWIRing? | A$ | Queries HARM-wiring | HARM ----------------------------------------------------------------------------- :SPOSItion W$,A | W$:W1 to W4 | Sets HARM-series | HARM | A:position(unit %) | zero position | | | for an input channel | ----------------------------------------------------------------------------- :SPOSItion? W$ | W$,A<NR1> | Queries HARM-series | HARM | | zero position | | | for an input channel | ----------------------------------------------------------------------------- :POSItion ch$, A| A: position value | Sets the zero position| MEM,REC,RMS | (unit %) | for an input channel. | ----------------------------------------------------------------------------- :POSItion? ch$ | ch$, A <NR1> | Queries the zero | MEM,REC,RMS | | position for an input | | | channel. | ----------------------------------------------------------------------------- :RANGe ch$, A | A: voltage or current | Sets input channel | MEM,REC,RMS | axis range | voltage or current | | (unit V,A) | axis range. | ----------------------------------------------------------------------------- :RANGe? ch$ | ch$, A <NR3> | Queries input channel | MEM,REC,RMS | | voltage or current | | | axis range. | ----------------------------------------------------------------------------- Command | Data | Explanation | Function | (for a query, | | | response data) | | ----------------------------------------------------------------------------- (5)DISPlay command (Setting and querying changeover of the screen mode, waveform display, etc.) :DISPlay ----------------------------------------------------------------------------- Command | Data | Explanation | Function | (for a query, | | | response data) | | ----------------------------------------------------------------------------- :CHANge A$ | A$:DISPlay,SET,SYSTem,| Changes over the | ALL | CARD | display screen. | ----------------------------------------------------------------------------- :CHANge? | A$ | Queries the display | ALL | | screen. | ----------------------------------------------------------------------------- :DIREct A$ | A$: | Switces directly to | ALL | DISPlay,DMM,STATus, | the specified setting | | CHANnel,TRIGger, | screen. | | EX_STatus,EX_TRIGger,| | | SCALing,CALCulation, | | | ENVIronment,COMMEnt, | | | RS_Copy,INITialize, | | | FILE,FILE_Conf | | ----------------------------------------------------------------------------- :DIREct? | A$ | Queries the display | ALL | | screen. | ----------------------------------------------------------------------------- :DRAWing ch$, A$| A$: OFF, C1 to C6 | Sets waveform display | MEM,REC,RMS | | color. | ----------------------------------------------------------------------------- :DRAWing? ch$ | ch$, A$ | Queries waveform | MEM,REC,RMS | | display color. | ----------------------------------------------------------------------------- :GRAPh ch$, A | A: 1, 2, 3, 4 | Sets waveform display | MEM,REC,RMS | (for DUAL format,1,2)| graph. | ----------------------------------------------------------------------------- :GRAPh? ch$ | ch$, A <NR1> | Queries waveform | MEM,REC,RMS | | display graph. | ----------------------------------------------------------------------------- :HDRAWing ch$, | A$:OFF,C1 to C6 | Sets HARM-INSTANT- | HARM A$ | | waveform disp color | ----------------------------------------------------------------------------- :HDRAWing? ch$ | ch$,A$ | Queries HARM-INSTANT- | HARM | | waveform disp color | ----------------------------------------------------------------------------- :HYZOOM A$ | A$:LOG,X1_2,X1,X2,X5, | Sets HARM-INSTANT- | HARM | X10,X20,X50,X100 | maginigication/ | | | compretion rario on | | | the voltage axi | | | (at non-wave) | ----------------------------------------------------------------------------- :HYZOOM? | A$ | Queries HARM-INSTANT- | HARM | | maginigication/ | | | compretion rario on | | | the voltage axis | ----------------------------------------------------------------------------- :SDRAWing W$,A$ | W$:W1 to W4 | Sets HARM-SERIES- | HARM A$:OFF,C1 to C6 | waveform disp color | ----------------------------------------------------------------------------- :SDRAWing? W$ | W$,A$ | Queries HARM-SERIES- | HARM | | waveform disp color | ----------------------------------------------------------------------------- :SXMAG A$ | A$:X1_48,X1_24,X1_12, | Sets HARM-SERIES- | HARM | X1_6,X1_4,X1_2,X1, | maginigication/ | | X2,X4 | compretion rario on | | | the time axis | ----------------------------------------------------------------------------- :SXMAG? | A$ | Queries HARM-SERIES- | HARM | | maginigication/ | | | compretion rario on | | | the time axis | ----------------------------------------------------------------------------- :SYMAG W$,A$ | W$:W1 to W4, | Sets HARM-SERIES- | HARM | A$:LOG,X1_2,X1,X2,X5, | maginigication/ | | X10,X20,X50,X100 | compretion rario on | | | the voltage axis | ----------------------------------------------------------------------------- :SYMAG? W$ | W$,A$ | Queries HARM-SERIES- | HARM | | maginigication/ | | | compretion rario on | | | the voltage axis | ----------------------------------------------------------------------------- :LOGDraw ch$, | A$: OFF, C1 to C6 | Sets logic waveform | MEM,REC,RMS N, A$ | N: 1, 2, 3, 4 | display color. | ----------------------------------------------------------------------------- :LOGDraw? ch$, N| ch$, N, A$ | Queries logic waveform| MEM,REC,RMS | | display color. | ----------------------------------------------------------------------------- :LOGPosi ch$, A | A: 1, 2, 3, 4 | Sets the position of | MEM,REC, | | logic waveform display.| RMS ----------------------------------------------------------------------------- :LOGPosi? ch$ | ch$, A <NR1> | Queries the position of| MEM,REC, | | logic waveform display.| RMS ----------------------------------------------------------------------------- :PAGE A | A: a number of page | Changes over the page | ALL | | of the screen. | ----------------------------------------------------------------------------- :PAGE? | A <NR1> | Queries the page of | ALL | | the screen. | ----------------------------------------------------------------------------- :SIZE A$ | A$: NORMal, NARRow | Sets the waveform | ALL | | display size. | ----------------------------------------------------------------------------- :SIZE? | A$ | Queries the waveform | ALL | | display size. | ----------------------------------------------------------------------------- :WAVE A$ | A$:ACUR,TRIG,POINT | Executes waveform | MEM | | display. | ----------------------------------------------------------------------------- :XAXIs, ch$ | ch$:CH1 to CH4 | In X-Y format, sets | MEM,REC | | the X-axis. | ----------------------------------------------------------------------------- :XAXIs? | ch$ | In X-Y format, queries| MEM,REC | | the X-axis. | ----------------------------------------------------------------------------- :XMAG A$ | A$:*10 to *1_500(MEM) | Sets the magnification/| MEM,REC, | *1 to *1_500 | compression ratio on | RMS | (REC, RMS) | the time axis. | ----------------------------------------------------------------------------- :XMAG? | A$ | Queries the magnificat | MEM,REC, | | -ion/compression | RMS | | ratio on the time axis.| ----------------------------------------------------------------------------- :XYCLr A$ | A$:ON, OFF | Sets the display clear| REC | | function. | ----------------------------------------------------------------------------- :XYCLr? | A$ | Queries the display | REC | | clear function. | ----------------------------------------------------------------------------- :YMAG ch$, A$ | A$:X1_2,X1,X2,X5,X10 | Sets the magnification/| MEM,REC, | | compression ratio on | RMS | | the voltage axis. | ----------------------------------------------------------------------------- :YMAG? ch$ | ch$, A$ | Queries the magnificat| MEM,REC,RMS | | -ion/compression ratio| | | on the voltage axis. | ----------------------------------------------------------------------------- Command | Data | Explanation | Function | (for a query, | | | response data) | | ----------------------------------------------------------------------------- (6)CURSor command (Cursor setting and reading) :CURSor ----------------------------------------------------------------------------- Command | Data | Explanation | Function | (for a query, | | | response data) | | ----------------------------------------------------------------------------- :ABCUrsor A$ | A$:A,ORA,ORB,A_B | Chooses among the A, B| MEM,REC,RMS | | and A&B cursors. | ----------------------------------------------------------------------------- :ABCUrsor? | A$ | Queries among the A, B| MEM,REC,RMS | | and A&B cursors. | ----------------------------------------------------------------------------- :ACHAnnel ch$ | ch$: CH1 to CH4,ALL | Sets the A cursor | ALL | | channel. | ----------------------------------------------------------------------------- :ACHAnnel? | ch$ | Queries the A cursor | ALL | | channel. | ----------------------------------------------------------------------------- :APOSition A | A:0 to amount of | Sets the position of | MEM,REC,RMS | stored data | the A cursor. | | (vertical and | | | trace cursor) | | | 0 to 400 | | | (X-Y format) | | | (horizontal cursor)| | ----------------------------------------------------------------------------- :APOSition? | A <NR1> | Queries the position | MEM,REC,RMS | | of the A cursor. | ----------------------------------------------------------------------------- :BCHAnnel ch$ | ch$:CH1 to CH4,ALL | Sets the B cursor | ALL | | channel. | ----------------------------------------------------------------------------- :BCHAnnel? | ch$ | Queries the B cursor | ALL | | channel. | ----------------------------------------------------------------------------- :BPOSition A | Same as :APOSition | Sets the position of | MEM,REC,RMS | | the B cursor. | ----------------------------------------------------------------------------- :BPOSition? | A <NR1> | Queries the position | MEM,REC,RMS | | of the B cursor. | ----------------------------------------------------------------------------- :DTREad? A$ | A$: A, B, B_A | Queries the cursor | ALL | B$,C$:readout value(t)| readout value (t). | ----------------------------------------------------------------------------- :DVREad? A$ |B$ (, C$) | Queries the cursor | ALL | A$: A, B, B_A | readout value (V). | | B$,C$:readout value(V)| | ----------------------------------------------------------------------------- :HABCUrsor A$ | A$:OFF,A,ORA,ORB,A_B | Chooses among the A, B| HARM | | and A&B HARM cursors. | ----------------------------------------------------------------------------- :HABCUrsor? | A$ | Queries among the A, B| HARM | | and A&B HARM cursors. | ----------------------------------------------------------------------------- :HAPOSition A | A:0 to 511 | Sets HARM-INSTANT- | HARM | | position of A cursor | ----------------------------------------------------------------------------- :HAPOSition? | A<NR1> | Queries HARM-INSTANT- | HARM | | position of A cursor | ----------------------------------------------------------------------------- :HBPOSition A | (same as HAPOSition) | Sets HARM-INSTANT- | HARM | | position of B cursor ----------------------------------------------------------------------------- :HBPOSition? | A<NR1> | Queries HARM-INSTANT- | HARM | | position of B cursor ----------------------------------------------------------------------------- :HDEGRee A | A:1 to 40 | Sets HARM-number | HARM | | of cursor | ----------------------------------------------------------------------------- :HDEGRee? | A<NR1> | Queries HARM-number | HARM | | of cursor | ----------------------------------------------------------------------------- :HMODE A$ | A$:OFF,ON | Sets HARM-A and B | HARM | | cursor type | ----------------------------------------------------------------------------- :HMODE? | A$ | Queries HARM-A and B | HARM | | cursor type | ----------------------------------------------------------------------------- :SAPOSition A | A:0 to storaged data | Sets HARM-SERIES- | HARM | | position of A cursor | ----------------------------------------------------------------------------- :SAPOSition? | A<NR1> | Queries HARM-SERIES- | HARM | | position of A cursor | ----------------------------------------------------------------------------- :SBPOSition A | (same as SAPOSition) | Sets HARM-SERIES- | HARM | | position of B cursor | ----------------------------------------------------------------------------- :SBPOSition? | A<NR1> | Sets HARM-SERIES- | HARM | | position of B cursor | ----------------------------------------------------------------------------- :SAWAve W$ | W$:W1 to W4,ALL | Sets HARM-SERIES- | HARM | | wave of A aursor | ----------------------------------------------------------------------------- :SAWAve? | W$ | Queries HARM-SERIES- | HARM | | wave of A aursor | ----------------------------------------------------------------------------- :SBWAve W$ | W$:W1 to W4,ALL | Sets HARM-SERIES- | HARM | | wave of B cursor | ----------------------------------------------------------------------------- :SBWAve? | W$ | Queries HARM-SERIES- | HARM | | wave of B cursor | ----------------------------------------------------------------------------- :MODE A$ | A$:OFF,TIME,VOLT,TRACe| Sets the A and B | MEM,REC,RMS | OFF,Xcur,Ycur,TRACe| cursor type. | | (in X-Y format) | | ----------------------------------------------------------------------------- :MODE? | A$ | Queries the A and B | MEM,REC,RMS | | cursor type. | ----------------------------------------------------------------------------- Command | Data | Explanation | Function | (for a query, | | | response data) | | ----------------------------------------------------------------------------- (7)MEMory command (Setting and querying input and output, etc., from the memory) :MEMory ----------------------------------------------------------------------------- Command | Data | Explanation | Function | (for a query, | | | response data) | | ----------------------------------------------------------------------------- :ADATa B, C,... | B, C,... : | Input data to memory | MEM | -2048 to 2047 | | | all <NR1> | (ASCII).| ----------------------------------------------------------------------------- :ADATa? A | B, C,...<NR1> | Queries Output data | MEM | A: 1 to 80 | from memory(ASCII). | | (number of | | | output units) | | | B, C,...:-2048 to 2047| | | all <NR1>| | ----------------------------------------------------------------------------- :AREAl? ch$ | A <NR1> | Output stored data. | MEM,REC,RMS | A: -2048 to 2047 | Real time data output.| | | (ASCII) | ----------------------------------------------------------------------------- :BDATa? A | A: 1 to 200 | Performs binary | MEM | (amount of | transfer for stored | | output data) | data. | | Response data:binary, | | | integer data | | ----------------------------------------------------------------------------- :BREAl? ch$ | Response data | Real time data output.| MEM,REC,RMS | :binary,integer data| (binary) | ----------------------------------------------------------------------------- :GETReal | | Captures real time data.| MEM,REC,RMS ----------------------------------------------------------------------------- :HPOINt ch$,A | A:1 to 40(number) | Sets HARM-INSTANT- | HARM | | point in memory of | | | output (at non-wave) | ----------------------------------------------------------------------------- :HPOINt? | ch$,A<NR1> | Queries HARM-INSTANT- | HARM | | point in memory of | | | output (at non-wave) | ----------------------------------------------------------------------------- :HVDATa? A | B,C<NR3>... | Queries HARM-INSTANT- | HARM | A:1 to 40(data num) | (at non-wave) | ----------------------------------------------------------------------------- :HVTOTal? ch$,A$| B<NR3> | output HARM-INSTANT | HARM | A$:T-RMS,THD-F,THD-R, | total data | | WATT,VA,VAR, | | | P-FACTOR | | ----------------------------------------------------------------------------- :HWPOINt ch$,A | A:0 to 511 | Sets HARM-INSTANT- | HARM | | point in memory of | | | output (wave) | ----------------------------------------------------------------------------- :HWPOINt? | ch$,A<NR1> | Queries HARM-INSTANT- | HARM | | point in memory of | | | output (wave) | ----------------------------------------------------------------------------- :HWVDATa? A | B,C<NR3>... | Queries HARM-INSTANT- | HARM | A:1 to 40(data num) | data (wave) | ----------------------------------------------------------------------------- :SMAXPoint? | A<NR1> | Queries HARM-SERIES- | HARM | 0=no data | amount of data stored | | 1 to 4800(60DIV*80point)| | ----------------------------------------------------------------------------- :SPOINt W$,A | W$:W1 to W4 | Sets HARM-SERIES- | HARM | A:0 to 4800(60DIV*80point) | point in memory of | | | output | ----------------------------------------------------------------------------- :SPOINt? | W$,A<NR1> | Queries HARM-SERIES- | HARM | | point in memory of | | | output | ----------------------------------------------------------------------------- :SVDATa? A | B,C<NR3>... | Queries HARM-SERIES- | HARM | A:1 to 40(data num) | data ----------------------------------------------------------------------------- :LDATa B, C,... | B,C,...:0 to 15 | Input logic data from | MEM | | memory. | ----------------------------------------------------------------------------- :LDATa? A | Response data | Output logic data from| MEM | <NR1>: 0 to 15 | | | A: 1 to 100 (amount of| memory. | | output data) | | ----------------------------------------------------------------------------- :LREAl? ch$ | A <NR1>: 0 to 15 | Logic real time data | ALL | | output. | ----------------------------------------------------------------------------- :MAXPoint? | A <NR1> | Queries the amount of | MEM | : 0 (not stored) | data stored. | | 80 to 256000 | | | (CH1 MAX) | | ----------------------------------------------------------------------------- :POINt ch$, A | A:0 to 256000 | Sets point in memory | MEM | (CH1 MAX) | for input and output. | ----------------------------------------------------------------------------- :POINt? | ch$, A <NR1> | Queries point in memory| MEM | | for input and output. | ----------------------------------------------------------------------------- :PREPare | | Prepares the memory | MEM | | for receipt of | | | waveform data. | ----------------------------------------------------------------------------- :VDATa B, C,... | B, C,...: | Input data to memory | MEM | (voltage values)| (voltage values). | ----------------------------------------------------------------------------- :VDATa? A | B, C,...<NR3> | Output stored data | MEM | A: 1 to 40 | (voltage values). | | (amount of data)| | ----------------------------------------------------------------------------- :VREAl? ch$ | A <NR3> | Real time data output | MEM,REC,RMS | A: voltage value | (voltage values). | ----------------------------------------------------------------------------- Command | Data | Explanation | Function | (for a query, | | | response data) | | ----------------------------------------------------------------------------- (8)SYSTem command (Setting and querying the system screen) :SYSTem ----------------------------------------------------------------------------- Command | Data | Explanation | Function | (for a query, | | | response data) | | ----------------------------------------------------------------------------- :BMPColor A$ | A$:COLOR,GRAY,MONO, | Sets the bit map file | ALL | MONO_R | color. | ----------------------------------------------------------------------------- :BMPColor? | A$ | Queries the bit map | ALL | | file color. | ----------------------------------------------------------------------------- :CHMArk A$ | A$: OFF, NUMBer, | Enables and disables | ALL | COMMent | channel markers. | ----------------------------------------------------------------------------- :CHMArk? | A$ | Queries enablement of | ALL | | channel markers. | ----------------------------------------------------------------------------- :COPY A$ | A$: IN_PRinter, PC, | Sets the output | ALL | COM | destination by the | | | COPY key. | ----------------------------------------------------------------------------- :COPY? | A$ | Queries the output | | | destination by the | | | COPY key. | ----------------------------------------------------------------------------- :CRTOff A | A: 0 (OFF), | Enables and disables | ALL | 1 to 30 (minutes) | the backlight saver. | | all <NR1> | | ----------------------------------------------------------------------------- :CRTOff? | A : <NR1> | Queries enablement of | ALL | | the backlight saver. | ----------------------------------------------------------------------------- :DATAClear | | Clear data. | ALL ----------------------------------------------------------------------------- :DATE | year: 0 to 99 | Sets the calendar. | ALL year, month, | month: 1 to 12 | | day | day: 1 to 31 | | ----------------------------------------------------------------------------- :DATE? | year, month, day | Queries the calendar. | ALL | (all <NR1>) | | ----------------------------------------------------------------------------- :GRID A$ | A$:OFF,STD,FINE, | Sets the grid type. | ALL | STD_Dark,FINE_Dark | | ----------------------------------------------------------------------------- :GRID? | A$ | Queries the grid type.| ALL ----------------------------------------------------------------------------- :LANGuage A$ | A$: JAPAnese, ENGLish | Sets the language. | ALL ----------------------------------------------------------------------------- :LANGuage? | A$ | Queries the language. | ALL ----------------------------------------------------------------------------- :LCDDisp A$ | A$:C1 to C16 | Sets the screen color.| ALL ----------------------------------------------------------------------------- :LCDDisp? | A$ | Queries the screen color.| ALL ----------------------------------------------------------------------------- :LIST A$ | A$: OFF, LIST, GAUGe, | Sets list and gauge | ALL | L_G | functions. | ----------------------------------------------------------------------------- :LIST? | A$ | Queries list and gauge| ALL | | functions. | ----------------------------------------------------------------------------- :LWIDth | A$:WIDE,NARRow | Sets logic recording | ALL | | width. | ----------------------------------------------------------------------------- :LWIDht? | A$ | Queries logic| | ALL | | recording width. | ----------------------------------------------------------------------------- :PRIDensity A | A$:LIGHt,STD,DARK | Sets the printer | ALL | | density. | ----------------------------------------------------------------------------- :PRIDensity? | A$ | Queries the printer | ALL | | density. | ----------------------------------------------------------------------------- :SOPEration A$ | A$:TIME1,TIME2,SEC2 | Sets the start key | ALL | | activation condition. | ----------------------------------------------------------------------------- :SOPEration? | A$ | Queries the start key | ALL | | activation condition. | ----------------------------------------------------------------------------- :STARt A$ | A$: ON, OFF | Enables and disables | ALL | | start backup. | ----------------------------------------------------------------------------- :STARt? | A$ | Queries start backup | ALL | | enablement. | ----------------------------------------------------------------------------- :TIME hour, min | hour: 0 to 23 | Sets the time. | ALL | min: 0 to 59 | | ----------------------------------------------------------------------------- :TIME? | hour, min, sec | Queries the current | ALL | (all <NR1>) | time. | ----------------------------------------------------------------------------- :TMAXis A$ | A$: TIME, TIME (60), | Sets the time axis | ALL | SCALe, DATE | display. | ----------------------------------------------------------------------------- :TMAXis? | A$ | Queries the time axis | ALL | | display. | ----------------------------------------------------------------------------- :USECH A | A: 1, 2, 4 | Sets number of | MEM | | channels used. | ----------------------------------------------------------------------------- :USECH? | A <NR1> | Queries number of | MEM | | channels used. | ----------------------------------------------------------------------------- Command | Data | Explanation | Function | (for a query, | | | response data) | | ----------------------------------------------------------------------------- (9)SCALing command (Setting and querying scaling) :SCALing ----------------------------------------------------------------------------- Command | Data | Explanation | Function | (for a query, | | | response data) | | ----------------------------------------------------------------------------- :KIND A$ | A$: POINT, RATIO | Sets the type of | MEM,REC,RMS | | scaling. | ----------------------------------------------------------------------------- :KIND? | A$ | Queries the type of | MEM,REC,RMS | | scaling. | ----------------------------------------------------------------------------- :OFFSet ch$, A | A: -9.9999E+9 to | Sets scaling offset | MEM,REC,RMS | +9.9999E+9 | (RATIO). | ----------------------------------------------------------------------------- :OFFSet? ch$ | ch$, A <NR3> | Queries scaling offset.| MEM,REC,RMS ----------------------------------------------------------------------------- :SCUPLOw ch$,B,C| B,C: -9.9999E+29 | Sets the scaling SC UP,| MEM,REC,RMS | to 9.9999E+29 | LOW (POINT). | ----------------------------------------------------------------------------- :SCUPLOw? ch$ | ch$,B,C<NR3> | Queries the scaling | MEM,REC,RMS | | SC UP, LOW. | ----------------------------------------------------------------------------- :SET ch$, A$ | A$: OFF, SCI, ENG | Enables and disables | MEM,REC,RMS | | scaling. | ----------------------------------------------------------------------------- :SET? ch$ | ch$, A$ | Queries scaling | MEM,REC,RMS | | enablement. | ----------------------------------------------------------------------------- :UNIT ch$, 'A$' | A$: scaling unit | Sets scaling unit. | MEM,REC,RMS | (7 characters) | | ----------------------------------------------------------------------------- :UNIT? ch$ | ch$, "A$" | Queries scaling unit. | MEM,REC,RMS ----------------------------------------------------------------------------- :VOLT ch$, A | A: -9.9999E+9 | Sets the scaling | MEM,REC,RMS | to +9.9999E+9 | conversion value | | | (RATIO). | ----------------------------------------------------------------------------- :VOLT? ch$ | ch$, A <NR3> | Queries the scaling | MEM,REC,RMS | | conversion value. | ----------------------------------------------------------------------------- :VOUPLOw ch$, | B,C:-9.9999E+29 | Sets the scaling VOLT | MEM,REC,RMS B, C | to 9.9999E+29 | UP, LOW (POINT). | ----------------------------------------------------------------------------- :VOUPLOw? ch$ | ch$, B,C <NR3> | Queries VOLT UP, LOW. | MEM,REC,RMS ----------------------------------------------------------------------------- Command | Data | Explanation | Function | (for a query, | | | response data) | | ----------------------------------------------------------------------------- (10)COMMent command (Setting and querying comments) :COMMent ----------------------------------------------------------------------------- Command | Data | Explanation | Function | (for a query, | | | response data) | | ----------------------------------------------------------------------------- :CH ch$, | ch$:CH1 to CH4, | Sets a comment for | ALL | CHA to CHB | a particular channel. | (NO$,) 'A$' | NO$:NO1 to NO4 | | | (logic only) | | | A$:comment string | | | (up to 24 characters)| | ----------------------------------------------------------------------------- :CH? ch$ (,NO$) | ch$, (NO$,) 'A$' | Queries comment for | | | a particular channel. | ----------------------------------------------------------------------------- :EACHch (ch$,) | ch$:CHA,CHB(logic only)| Enables or disables | ALL A$ | A$:OFF,SETTing,COMMent,| a channe comment. l | S_C(analog) | | | A$:OFF,COMMent(logic) | | ----------------------------------------------------------------------------- :EACHch? (ch$,) | (ch$,) A$ | Queries channel | | | comment enablement. | ----------------------------------------------------------------------------- :TITLe A$, 'B$' | A$:OFF,SETTing,COMMent,| Sets a title comment.| ALL | S_C | | | B$: comment string | | | (up to 24 characters)| | ----------------------------------------------------------------------------- :TITLe? | A$, "B$" | Queries a title comment.| ALL ----------------------------------------------------------------------------- Command | Data | Explanation | Function | (for a query, | | | response data) | | ----------------------------------------------------------------------------- (11)CALCulate command (Calculation setting and querying) :CALCulate ----------------------------------------------------------------------------- Command | Data | Explanation | Function | (for a query, | | | response data) | | ----------------------------------------------------------------------------- :ANSWer? NO$, | A$,B<NR3> | Queries a calculation | MEM ch$ | NO$:NO1 to NO4 | result. | | A$:OFF,AVE,RMS,PP,MAX,| | | MIN,MAXT,MINT,AREA,| | | PERI,FREQ,XYAREA | | | B:calculation result | | ----------------------------------------------------------------------------- :MEASFsave A$ | A$:OFF,ON | Sets storing | MEM | | a calculation result. | ----------------------------------------------------------------------------- :MEASFsave? | A$ | Queries storing | MEM | | a calculation result. | ----------------------------------------------------------------------------- :MEASPrint A$ | A$:OFF,ON | Sets printing | MEM | | calculation results. | ----------------------------------------------------------------------------- :MEASPrint? | A$ | Queries printing | MEM | | calculation results. | ----------------------------------------------------------------------------- :MEASSet NO$, | NO$:NO1 to NO4 | Sets numerical | MEM A$, ch$ | A$:OFF,AVE,RMS,PP,MAX,| calculation item. | (,ch2$ | MIN,MAXT,MINT,AREA,| | (XYAREA)) | PERI,FREQ,XYARea | | | ch$:ALL,CH1 to CH4 | | ----------------------------------------------------------------------------- :MEASSet? NO$ | A$, ch$ | Queries numerical | MEM | | calculation item. | ----------------------------------------------------------------------------- :MEASure A$ | A$:ON,OFF, | Sets numerical | MEM | EXEC(execute) | calculation. | ----------------------------------------------------------------------------- :MEASure? | A$ | Queries numerical | MEM | | calculation. | ----------------------------------------------------------------------------- Command | Data | Explanation | Function | (for a query, | | | response data) | | ----------------------------------------------------------------------------- (12)FDISK command (Setting and querying file operation) :FDISK ----------------------------------------------------------------------------- Command | Data | Explanation | Function | (for a query, | | | response data) | | ----------------------------------------------------------------------------- :CHDIR NO | NO: file number | Changes the current | ALL | | directory. | ----------------------------------------------------------------------------- :DELEte NO | NO: file or directory | Deletes a file or | ALL | number | a directory. | ----------------------------------------------------------------------------- :DIR? | A$: directory name | Queries the current | ALL | | directory. | ----------------------------------------------------------------------------- :FILE? | A <NR1> | Queries the number of | ALL | :number of files | files. | ----------------------------------------------------------------------------- :FORMat | | Formats media. | ----------------------------------------------------------------------------- :FREE? | A$: allowable number | Queries the allowable | ALL | of bytes | number of bytes. | ----------------------------------------------------------------------------- :INFOr? NO | NO,"NAME$","DATE$", | Queries information | ALL | "TIME$",A,B$,C$,D, | about a file. | | "TDATE$,"TTIME$" | | | NO:file and directory number | | | NAME$: file and directory name | | | DATE$: year/month/day of save | | | TIME$: hour:min:sec of save | | | A: file size (bytes) | | | B$: function | | | C$: measurement contents | | | D: recording length | | | TDATE$: year/month/day of trigger | | | TTIME$: trigger time | | ----------------------------------------------------------------------------- :LOAD NO (,A$) | NO: file number | Load a file. | ALL | A$: NEW, ADD | | ----------------------------------------------------------------------------- :MKDIR 'A$' | A$: directory name | Creates a directory. | ALL ----------------------------------------------------------------------------- :NINFor? NO | NO, "NAME$", A$ | Queries filename. | ALL | NO:file number | | | NAME$: file name | | | A$:directory of a file | | ----------------------------------------------------------------------------- :SAVE 'NAME1$. | NAME1$: file name | Saves a file. | ALL NAME2$', A$, | (up to 8 characters) | | B$ (, C$)| NAME2$: file extension | | | (up to 3 characters) | | | | | | A$: type of file(memory segmentation:OFF) | | | Bin: binary data | | | Text: text data | | | Set: settings | | | A$: type of file(During memory segmentation) | | | BAll:binary data(All blocks are saved.) | | | BOne:binary data(One block is saved.) | | | TALL:text data(All blocks are saved.) | | | TOne:text data(One block is saved.) | | | B$: channels to save | | | ALL, CH1 to CH4, LOGIC | | | C$: spacing | | | OFF,1_2, to 1_800 | | ----------------------------------------------------------------------------- :SORT A$ | A$:ON,OFF | Sets the file list | ALL | | sorting. | ----------------------------------------------------------------------------- :SORT? | A$ | Queries the file list | ALL | | sorting. | ----------------------------------------------------------------------------- :STYPe A$ | A$:NAME,TYPE,TIME,SIZE| Sets the sort order | ALL | | type for the file list.| ----------------------------------------------------------------------------- :STYPe? | A$ | Queries the sort order | ALL | | type for the file list.| ----------------------------------------------------------------------------- :SDIRection A$ | A$:UP,DOWN | Sets the sort | ALL | | direction setting of | | | the file list. | ----------------------------------------------------------------------------- :SDIRection? | A$ | Queries the sort | ALL | | direction setting of | | | the file list. | -----------------------------------------------------------------------------Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.