1. 2560fx22.exe Driver
2. LANSERV.TXT File Contents

LANSERV.TXT Driver File Contents (2560fx22.exe)

   LAN Server
                                                                
AT-2560FX

LAN Server installation notes for ATI AT-2560 PCI LAN Adapters:
==============================================================

Location of files:  \NDIS\A2560.OS2   (OS/2* driver)
                    \NDIS\A2560EO2.NIF
      
                         or
      
                    \NDIS\A2560.DOS   (DOS driver)
                    \NDIS\A2560EDS.NIF (DLR and LSP installation file)

NOTE: LAN Requester needs DOS 3.3 through 5, but if you're using DOS 6.0
      or higher, run SETVER.EXE prior to using the executable files 
      found on the DOS LAN Requester disks. See your DOS manual if you 
      need help with SETVER.EXE.


Sample configuration file
-------------------------

PROTOCOL.INI (will include):

[A2560_NIF]
   DriverName = A2560$
   SPEED = 100
   FORCEDUPLEX = 2


General installation - LAN Server and OS/2 Requester (4.0 or 3.0)
-----------------------------------------------------------------

1. Run the MPTS utility with LAN Server 4.0 or OS/2 Requester 4.0 (Run
   the LAPS utility with LAN Server 3.0 or OS/2 Requester 3.0)

2. Click Install.

3. When prompted, insert the Configuration and Drivers disk in a
   floppy drive, specify A:\NDIS for driver location, and click OK.

4. When Install reads the A2560EO2.NIF, installation is complete. Click
   OK. The adapter driver has been copied to your system.

5. Click Configure from the MPTS window.

6. At the Configure window, make sure the LAN adapters and protocols
   button is on and click CONFIGURE.

7. At the LAPS Configuration window, select the AT-2560 PCI adapter
   (OS/2 driver: A2560.OS2) from the Network Adapters window.
  
   Click Add in the Network Adapter window to add the adapter to the
   current configuration.

8. Select your desired Protocol(s) from the Protocol window and click 
   Add from this window to add the protocol(s) to the current 
   configuration.

9. Click OK when you're done and follow the prompts to exit MPTS. Your
   CONFIG.SYS is automatically updated.
  
   Shutdown and reset your system so the changes can take effect.


General installation under DOS (DOS LAN Services)
=================================================

NOTE: Due to a problem with the DLS installation utility, you need to
      complete the following steps before executing the installation of
      DLS:
   
      1. On DLS Diskette 1, make a directory off the root called NDIS.
      
      2. Copy the file A2560.DOS (from the \NDIS directory of the 
         Configuration and Drivers) into this new directory \NDIS on DLS
         Diskette 1.


Setup Instructions
------------------

1. Run the DOS LAN Services installation program at the DOS workstation.
   Follow the prompts.

2. When presented with an adapter list, select Network card not shown in
   list below.

3. When prompted for the location of the OEMSETUP.INF file, insert the
   Configuration and Drivers disk in your drive and enter A:\NDIS
   as the path.

4. Select the ATI AT-2560 PCI adapter from the list.  Follow
   the prompts.

5. Enter your machine name, username and domain name.

6. Set the options as you need; then highlight "The listed options are
   correct" and press Enter.

7. Accept the defaults on the next screen, highlight "The listed options
   are correct" and press Enter.

8. Change the Duplex mode, or set Slot Device if needed. We recommend
   accepting the defaults. Then highlight "The listed options are
   correct" and press Enter.

9. You may be asked to insert DLS disks. Follow the prompts to complete
   the installation and restart your computer for changes to take 
   effect.


General Installation under DOS: LAN Support Program (LSP)
=========================================================

1. Run DXMAID from the LAN Support Program disk.

2. Follow the prompts and instructions.

3. When prompted, insert the Configuration and Drivers disk and
   enter the pathname A:\NDIS.

4. The default configuration is suitable for most environments.  We
   recommend accepting the defaults.

5. After the installation is complete, restart your computer for the
   changes to take affect.


General Installation under DOS (DOS LAN Requester)
==================================================

1. Run the DOS LAN Requester installation program at the DOS 
   workstation. Follow the prompts to configure your DOS LAN Requester 
   as you require.

2. After the installation is complete, restart your computer for the
   changes to take effect.


Advanced settings
=================
   
   SPEED: (mandatory; parameter is 100) The parameter causes the adapter 
   to function at the speed indicated. 
   
   FORCEDUPLEX: 
  
   Options for FORCEDUPLEX are 1 (for half), 2 (for full). 
   [Example: FORCEDUPLEX = 2]
   
   SLOT: (required for multiple adapters) This parameter is optional if
   only one adapter is present.  If it is specified but is incorrect,
   a message indicates that the value doesn't match the configuration
   but the driver finds the adapter and loads anyway.
   
   This parameter is required if more than one adapter is present in
      either one bus or multiple PCI buses of a system. The parameter
      tells the driver which adapter it controls. The SLOT number is the
      encoded value of the PCI adapter's device location. To determine
      the slot number, load the driver with only the DRIVERNAME 
      parameter specified.  The driver reports all the slots that have 
      PCI adapter(s) installed. You can determine which card is in which 
      slot by using SETUP.EXE and matching the Ethernet addresses of the
      adapter to the device number specified in View Configuration.
      [Example: SLOT=0x1C]



*  Third-party trademarks are the property of their respective 
   owners.