[String] App Name = Wireless-N Broadband Router 150Mbps / 1T1R welcome = Welcome info = Use this utility program for initial setup of the device and whenever changes to the system configuration are required, such as Internet Access or IP Address settings. For detailed configuration instructions refer to the User Manual. webURL = www.kraun.it Model No. = Model No.: KR.1N Version No. =\r\n Product Name = Wireless-N Broadband Router 150Mbps / 1T1R Setup1 Title = Connect the included Power Adapter to the Router and the nearest Power Socket. Setup2 Title = Connect a Network Cable from a LAN Port of the Router to the Network Adapter Socket of your PC. Setup3 Title = Connect a Network Cable from the WAN Port of the Router to the Modem or other Internet Connection Device provided by your ISP. Setup4 Title = LED Indicator Description. Setup5 Title = Please select your Broadband Connection Type. PPPoE Title = ADSL Virtual Dialing (PPPoE) Static IP Title = Static IP PPTP Title = PPTP Mac clone Title = MAC Address Clone Wireless Title = Wireless Basic Settings Security Title = Wireless Security Settings Result Title = Running Status Connect failed =Connection Failure Connect Failed Des =1. Check the Router and Cables again.\r\n2. Check the Power Adapter.\r\n3. Restore the Router to Factory Default Settings\r\nas shown in the diagram. Connect Failed Note =Keep pressing "Reset" button for about 7 seconds when \r\nthe device is powered on. Auto detect = 1. Auto detect Detect manually =\r\n Dynamic IP Desc = * Ethernet Broadband, get IP automatically (Dynamic IP) PPPoE Desc = * PPPoE PPTP Desc = * PPTP L2TP Desc = * L2TP Static IP Desc = * Ethernet Broadband, Fixed IP (Static IP) Success = OK Auto detection failure = Auto Detection Failure Auto detection failure Desc =1. Please check if the WAN cable connection is OK.\r\n2. Please check if the WAN indicator is flashing normally.\r\n3. Please ensure the modem works properly. Your connection way = Your connection method: Static IP = Static IP Dynamic IP = Dynamic IP PPPoE = PPPoE (ADSL) PPTP = PPTP Account = Account Password = Password Check Accounts = Check Accounts Check accounts inaccuracy = Account Name or Password incorrect! Check accounts correct = Account Name and Password correct! Server IP Address = Server IP Address User Name = User Name Address Mode = Address Mode Static = Static Dynamic = Dynamic IP Address = IP Address Subnet Mask = Subnet Mask Default Gateway = Default Gateway Primary DNS = Primary DNS Secondary DNS = Secondary DNS MAC Clone Attention = (Do not modify unless required by your ISP.) Clone Mac = Clone MAC Address Restore Mac = Restore Default MAC Add. SSID = SSID Wireless Mode = Wireless Mode Channel = Channel SSID Broadcast = SSID Broadcast Disable = Disable Auto = Auto Select HostName = KRAUN_N01 SSID Value = KRAUN_N01 802.11b/g Mixed = 802.11b/g Mixed 802.11b/g/n Mixed = 802.11b/g/n Mixed Mixed = Mixed Wireless Note = Here you may change the Wireless Network Name, Protocol and Channel. Security Note = If enabled, please select the Wireless Encryption Mode. Example: If WPA Encryption is selected, enter 8~63 ASCII characters (digits or letters). This will be the secret key for the Wireless Network of the Router. WEP = WEP WPA = WPA WPA2 = WPA2 Open = Open Share = Share AES = AES TKIP = TKIP Key 1 = Key 1 Key 2 = Key 2 Key 3 = Key 3 Key 4 = Key 4 Security = Security Authentication Mode = Authentication Mode Key Type = Key Type Transmit Key = Transmit Key Key = Key WEP Key Invalid = Key valid length is:\r\n 64-bit: 10 characters,\r\n 128-bit: 26 characters. WEP Security Note = Key Description: 64-bit Encryption requires 10 ASCII or 5 Hex characters, 128-bit Encryption requires 26 ASCII or 13 Hex characters (Permitted characters: Hex 'A-F' and digits '0-9', ASCII 'aA-zZ', digits '0-9', underline). WPA Key Mode = WPA Key Mode WPA2 Key Mode = WPA2 Key Mode WPA Key = WPA Key WPA2 Key = WPA2 Key Key Valid Time = Key Valid Time 8~63 ASCII characters = (8~63 ASCII characters) s.60s~9999s = s. (30s~9999s) WPA Key Invalid = Invalid Key Length! \r\nWPA requires 8~63 ASCII characters. Key Time Invalid = Key valid Time Invalid. WAN link mode = WAN Link Type Encryption Mode = Encryption Mode Enable = Enable Status Note = Note: If the IP Address shows 0.0.0.0, please wait one minute and click the Refresh button to check the IP Address again. If the IP address is still 0.0.0.0, please contact your provider for the correct configuration information. Configuration is successful when IP address is other than 0.0.0.0.\r\n Manual = Manual Next = Next Back = Back Start =Start Exit = Exit Finish =Finish Refresh = Refresh Reboot = Reboot Retry = Retry OK = OK Yes = Yes No = No Warning = Warning Error = Error link mode = Link Mode gateway = Gateway wirless mode = Wirless Mode Account Empty = User Name cannot be blank.\r\n Please enter your User Name! Password Empty = Password cannot be blank. \r\nPlease enter your Password! IP address invalid = IP Address is invalid! Subnet mask invalid = Subnet Mask is invalid! Default gateway invalid = Default Gateway is invalid! Primary DNS server invalid = Primary DNS Server Address is invalid! Mac address invalid = Mac Address is invalid! SSID invalid = Invalid SSID! (Permitted characters: letters, digits, underline) Leave Massage = Are you sure you want to exit the Wizard? prg_link = Connecting to the Router... please wait! prg_auto = Checking your Link Mode... please wait! prg_check = Checking now... please wait! prg_save = Saving... please wait! prg_reboot = Restarting... please wait! Connect OK = Successfully connected to the Router! Save OK = Saved successfully, click the "OK" button to restart the Router.Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.