_______________________________________________________________________________________________ Changes from 1.06.08.14/15/16 - Win 7, Vista, and XP 32/64 WHQLed - GUI fix - "verifier/standard/all" BSOD fix - Experimental EM Unload (.15/.16 version) implementation, standard Unload is final _______________________________________________________________________________________________ Changes from 1.06.08.13 - Win 7, Vista, and XP 32/64 WHQLed - REV 14 target to all ODMs _______________________________________________________________________________________________ Changes from 1.06.08.12 - New registry for 20msec duration setting - GUI fix - TEST DRIVER ... NOT FOR ALL ODMS _______________________________________________________________________________________________ Changes from 1.06.08.11 - New service to add filter on 2nd HDD and prompt for reboot if needed. has been tested on Vista32 and Win7 32 bit OSes. - GUI to meet Dell requirement - Registry entry for AW - Test driver so that it loads on all Intel PCHs with PID 0x3BXX. !THIS DRIVER RELEASE IS UNSIGNED! To run on Vista64 or Win7 64 OS, use two methods below: 1. press F8 at boot to disable signing check 2. enable loading of test signed sw as follows: - From Administrator command prompt run - "bcdedit /set testsigning on" - reboot _______________________________________________________________________________________________ Changes from 1.06.08.10 - Win 7 and XP 32/64 WHQLed _______________________________________________________________________________________________ Changes from 1.06.08.09 - Fix WHQL DTM issue _______________________________________________________________________________________________ Changes from 1.06.08.08 - Vista 32/64 driver WHQLed _______________________________________________________________________________________________ Changes from 1.06.08.07 - GUI and language change - New control panel icon - update registry _______________________________________________________________________________________________ Changes from 1.06.08.06 - Registry change, no driver change _______________________________________________________________________________________________ Changes from 1.06.08.05 - Registry change, no driver change _______________________________________________________________________________________________ Changes from 1.06.08.04 - Test release _______________________________________________________________________________________________ Changes from 1.06.08.03 - GUI apps S3, S4, Power Down resume behavior (keep OK and Cancel option) - Free fall interrupt setting 400Hz, 4 samples, threshold 0x17 - Un-safe motion detection setting 400Hz, 15 samples, threshold 0x14 - GUI apps registry control - Setup_AW... (for Alienware GUI) - Setup_Dell... (for Dell GUI) _______________________________________________________________________________________________ Changes from 1.06.08.02 - Support Capella/IbexPeak PCH - GUI apps (remove accept) - HDD protection default to interrupt mode (registry setting) - Add AW GUI _______________________________________________________________________________________________ Changes from 1.06.08.01 - setup executable (supports XP/Vista/Win7) - as single package end user mode - /nodrv factory installation, install filter and GUI - /s silent installation mode - Sensor driver (for factory installation) x86 directory: 32-bit accelerometer driver binaries x64 directory: 64-bit accelerometer driver binaries Notes: 1) While testing silent installation, the unsigned driver warnings is expected - Will be resolved when the drivers get WHQLed. 2) Press F8 while booting 64-bit OS and disable unsigned driver check each time boot - Otherwise the machine will blue screen while booting. Will be resolved after WHQLed. 3) CPL file is not installed on 64-bit systems - Only 32-bit OS installation with GUI in Control Panel.Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.