====================================================================== Release notes for the Intel(R) Embedded Graphics driver package for Microsoft Windows* Version 3.4.3, April 2005 ====================================================================== Contents ======== - New Features - System Requirements - In This Release - Installation and De-installation - Software Errata - Software Licenses - Legal / Disclaimers New Features ============ This release adds advanced capability to configure EDID usage, in order to eliminate the need for multiple INF files for different display configurations on a single platform. System Requirements ==================== Development system should have one the following Windows operating systems installed. Microsoft* Windows XP Professional* SP1 Microsoft* Windows XP Embedded* SP1 Microsoft* Windows 2000* SP4 Microsoft* Windows NT* 4.0 SP6 Target system must contain one of the following Intel Chipsets: Intel(R) 855GME Chipset Intel(R) 852GME Chipset Intel(R) 845GV Chipset Intel(R) 815 Chipset Intel(R) 815E Chipset Please check with your system provider to determine Intel Chipset used in your system. The drivers provided by this package have been tested using the following firmware version: AMI* BIOS version: 08.00.09 AMI* BIOS build date: 05/21/2003 AMI* BIOS ID: 049 The system should contain a minimum of 128MB of RAM. In This Release (Bill of Materials) =================================== This package contains the following files: Documents\RELNOTES.TXT Release Notes Documents\Errata.pdf Errata Document License\display_license.txt License file for display driver Driver\igdmini.sys Display driver Driver\igddis.dll High level Interface Dynamic Link Library Driver\igd3dalm.dll Direct3D support Dynamic Link Library Driver\ssigd.inf Install file for Display driver Driver\ssigd_alm.sld Windows XP* Embedded Component definition file (other than 815 platforms) Driver\ssigd_wht.sld Windows XP* Embedded Component definition file for 815 platforms Driver\ch7009.sys Port driver for Chrontel CH7009/CH7301 encoder Driver\ch7017.sys Port driver for Chrontel CH7017/CH7305 encoder Driver\cx873.sys Port driver for Conexant 873 TVOut encoder Driver\fs454.sys Port driver for Focus 453/454 TVOut encoder Driver\fs460.sys Port driver for Focus 461/462 TVout encoder Driver\lvds.sys Port driver for Internal (GMCH) LVDS controller Driver\ns2501.sys Port driver for National 2501 LVDS controller Driver\ns387.sys Port driver for National 387R LVDS controller Driver\rgba.sys Port driver for GMCH RGBA port Driver\th164.sys Port driver for Thine 164 encoder Driver\tl955.sys Port driver for Teralogic 955 RGBA encoder Driver\sii164.sys Port driver for Silicon Image 164 encoder Driver\sdvo.sys Port driver for SDVO devices Utilities\display_license.txt License file for display driver Utilities\IEGDGUI.dll Library file for display modes GUI Utilities\IEGDGUI.exe Stand-alone display modes GUI executable Utilities\pcf2iegd.exe Utility for conversion of PCF files Utilities\qt-mt332.dll Library required for display modes GUI Utilities\Setup.exe Install/uninstall utility for driver Utilities\SetupNT.exe Install/uninstall utility for Windows NT version of driver Installation and De-installation ================================ This release contains an installer/uninstaller utility. This utility however does not configure the driver. Please be sure to update your ssigd.inf file with appropriate settings for your display configuration prior to installation. The installation program requires specific file names, so if you have a different INF file for driver installation, you must name it ssigd.inf and place it in the Drivers folder prior to running the installation. Do not move or alter the directories after unzipping the release package. The installation utility uses relative path information, and must be run from the Utilities folder, and also requires the Driver folder. If the folders are moved or renamed, the installation utility will not operate properly. Also, be sure to not install this version of the driver with an existing installation of a previous version of the driver. The installation utility will not uninstall previous versions of the Intel Embedded Graphics Driver, and you must begin from a fresh operating system installation. Results are unpredictable if you install over a previous version of the Intel Embedded Graphics Driver. To run the installation, simply run the Setup.exe program located in the Utilities folder of the installation. This must run from the Utilities folder. If you are running Microsoft Windows NT*, you must instead run SetupNT.exe. To uninstall this version of Intel Embedded Graphics Driver, run the Setup.exe program (or SetupNT.exe for Microsoft Windows NT). Software Errata =============== Please see the errata document included with this release for errata details. Software Licenses ================= The Intel(R) Embedded Graphics Display Driver for Windows* is subject to the terms of the license agreement located in the display_license.txt file in this distribution package. Legal / Disclaimers =================== Copyright (C) 2003, 2004, 2005, Intel Corporation. All rights reserved. Intel Corporation assumes no responsibility for errors or omissions in this document. Nor does Intel make any commitment to update the information contained herein. * Other product and corporate names may be trademarks of other companies are used only for explanation and to the owners' benefit, without intent to infringe. ======================================================================Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.