[DS] PATH=\twain_32\Avision\AV220\ DSNAME=AV220.DS VERSION_INFO=5.01.0516'06 MANUFACTURER=Avision PRODUCTFAMILY=Scan Manager PRODUCTNAME=AV220 INTERFACE=AV220.dll UIALWAYSON=0 WARMUPTIMES=1 SAVEPATH=C:\AV220\ BatchScanSetting=0 [LANGUAGE] LANGUAGE=English [English] &EASY=simple.dll &BASIC=basic.dll &EXPERT=advance.dll TWDSM=twdsm_n.dll SCANMODE=avscan_n.dll UIDSM=uidsm_n.dll Err999=Can not find the device driver or power off or cable failure. Err1=Can not find the scanner. Err2=Scanner R/W test fails. Err3=Scanner connection fails. Err4=Scanner RAM test fails. Err5=Scanner RAM test fails. Err6=Scanner DMA test or power cable fails. Err7=Calibration fails. Err8=Scanner internal error. Err9=Paper feed error. Err10=Sensor error. Unlock the scanner by turning the lock switch to the "Unlocked position". Err11=Transparency calibration error. Err101=Power off or cable fails. Err102=Please remove the shipping retainer. Err103=Paper jam. Err104=The cover of auto document feeder is open. Err105=No paper in the auto document feeder. Err106=Job separation sheet detected. Err107=To scan transparency, you must first install a transparency kit. Err108=Transparency kit turns off. Err109=Internal target fails. Err110=Fuse blown out. Err111=Fuse blown out. Err112=Fuse blown out. Err113=Fuse blown out. Err114=Mechanical system failure. Err115=Optical system failure. Err116=Illegal scanner parameter. Err117=Illegal scanner parameter. Err118=Illegal scanner parameter. Err119=Illegal scanner parameter. Err120=Illegal scanner parameter. Err121=Message error. Err122=Image transfer error. Err123=Unknown error. Err124=No ASPI managers are found. Err125=Can not find SCSI ASPI. Err126=An ASPI manager which does not support Windows is resident. Err127=Insufficient memory. Err128=Can not find winaspi.dll or wnaspi32.dll. Err129=Can not find the scanner. Err130=Can not initialize SCSI manager. Err50=Termination timeout. Err51=Reverse timeout. Err52=Forward timeout. Err50=Negotiation timeout. Err150=Driver busy. Err151=Parameter check error. Err152=Allocating memory fails. Err153=Driver initial fails. Err154=Scanner internal error. Err155=Scanner connection fails. Err156=Reading image error. Err157=Reading image error. Err158=End image error. Err159=Stop scanning due to pressing the Stop button. Err160=Driver initial fails. Err161=Sending scanner parameter fails. Err162=Scanner busy. Err163=Sending command error. Err164=Scanner warms up. Err165=Power off. Err170=Parallel not found. Err171=Scanner connection fails. Err172=Scanner connection fails. Err173=Scanner connection fails. Err174=Scanner initial fails. Err175=Scanner initial fails. Err176=Back to home position fails. Err177=Search start position error. Err178=Lamp can not be turned on. Err179=Scanner lock error. Err250=System error. Err251=Driver internal error. Err2000=Driver busy Err2001=Scanner busy Err2002=I/O port is busy. Err2003=HandShake time Out. Err2004=Scanner connection fails. Err2005=Parameter check error. Err2006=Allocating memory fails. Err2007=Lamp can not be turned on. Err2008=Scanner locked. Err2009=Scanner warms up. Err2010=Stop scanning due to pressing the Stop button. Err2011=Register R/W verification fails. Err2012=Memory R/W verification fails. Err2013=Paper jam. Err2014=The cover of the auto document feeder is open. Err2015=No paper in the auto document feeder. Err2016=Can not find the transparancy kit. Err2017=Transparancy kit is power off. Err2018=Can not find winaspi. Err2019=Can not find the scanner. Err2020=Calibration fails. Err2021=Back to home position fails. Err2022=End of page. Err2023=Operation system return error. Err2024=Write NVM Error. Err2999=Unknow error Err3001=Flatbed home sensor error. Err3002=ADF home sensor error. Err3003=Flatbed DRAM error. Err3004=ADF DRAM error. Err3005=Flatbed lamp error. Err3006=ADF lamp error. Err3007=Document cover is open. Err3008=Accessories such as ADF is plugged out. Err3009=Prefeeding. Err3101=Multiple feed. IDS_LOWMEMORY=Low memory. Please free some memory and try again. IDS_NOPAPER=No paper in the auto document feeder. IDS_NOPAPER1=Please load the paper and try again. IDS_NODISK=Not enough disk space IDS_NODISK1=Please free some disk space and try again. IDS_WRITEERROR=Write to file error. IDS_WRITEERROR1=It may be either: IDS_WRITEERROR2=1.) Disk full IDS_WRITEERROR3=2.) Disk write protect IDS_WRITEERROR4=Please check again. IDS_TRANSFER=Transfer IDS_CHUNKY=Data Chunky && Transfer IDS_MEMORY_P=Buffered Memory / P IDS_MEMORY_C=Buffered Memory / C IDS_NATIVE=Native Memory IDS_NATIVE_P=Native Memory / P IDS_DISK=Disk File IDS_DISK_P=Disk File / P IDS_MEMORY=Buffered Memory IDS_SCAN=Scanning... IDS_PREVIEW=Preview... IDS_TESTSCANNER=Scanner testing IDS_CONNECTING=Connecting scanner IDS_CANCEL=Cancel IDS_TRANSFERMODE=Transferring Mode : CaliTitle=Do Calibration... IDS_PUTPAPERMSG=Put a white and clean paper on the scanner. IDS_WAIT=Please wait... IDS_BADSIZE=Scan size < 1 inch IDS_BADWIDTH=Scan width is too large IDS_EASYUI=This UI will be changed to EASY version. IDS_PRINTWORKING=There are print jobs processing, please wait till all print jobs are done. IDS_SCANNERSUCCESS=Scanner successful! IDS_SCANNERFALSE=Scanner disconnect! IDS_SCANNERUNKNOW=Scanner unknown! IDS_ENERGY=Closing 'Scanner Utility' will disable the 'Energy Saving' setting IDS_WARING=Warning IDS_ERRORCODE=Error Code IDS_CHANGEMODE=To scan film, you must first install a transparency kit. IDS_CONNECTSUCCESS=Scanner success ! IDS_CONNECTFAILURE=Scanner failure ! IDS_CONNECTUNKNOW=Scanner Unknown ! IDS_WARMUP=Scanner lamp has not warmed up yet... IDS_SECOND=Second IDS_WAIT=Please wait... WARMUPTITLE=Warm up scanner MATCHFILE=Can not find the color match file. IDS_TRANSFERRING=Transferring... IDS_SCANNINGPAGETEXT=Scanning Page IDS_ELAPSED=Elapsed Time : IDS_RECEIVED=Received Size : IDS_TOTALRECEIVED=Total Size : IDS_MULTIFEED=Multifeed is detected, please remove the rest paper from ADF. IDS_FILETYPEERROR=The compression does not support this type of file format. Err3025=Please Insert the Calibration Card [UI Version] UI Num=3 0=&EASY 1=&BASIC 2=&EXPERT [&EASY] function=CreateSimpleDialog Curve=0 [&BASIC] function=_CreateBasicDialog Curve=0 [&EXPERT] function=CreateAdvanceDialog Curve=1Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.