English.ini Driver File Contents (Epu6Engine_V10210.zip)

ÿþ[Translations]



CanNotRunUnderBiosOc = "EPU cannot launch under the current overclocking settings. Please restart your system, load the EPU default settings in BIOS, and launch EPU again."



CanNotRunUnderApOc = "EPU cannot launch under the current overclocking settings. Please restart your system to clear TurboV/TurboKey overclocking settings and launch EPU again." 



CanNotRunUnderOverclockingmode = "EPU cannot run on overclocking mode. Please turn off the overclocking mode from the BIOS setup or use the ASUS overclocking utilities."



CanNotRunUnderAISuite ="EPU cannot run simultaneously with AI Suite. Please close AI Suite first before running the EPU."



CanNotRunUnderTurboV ="Please close the TurboV window before launching EPU."



SubTitle = "the complete system power saving solution"



ModeSetting = "Mode Setting"



CurrentStatus = "Current Status"



Tranquility = "Tranquility"



Performance = "Performance"



Reliability = "Reliability"



Convenience = "Convenience"



EnergySaved = "Energy Saved"



Setting = "Setting"



Calibrate = "Calibrate"



Exit = "Exit"



HintL0  = "Auto Mode"



HintL1  = "Turbo Mode"



HintL2  = "High Performance Mode"



HintL3  = "Medium Power Saving Mode"



HintL4  = "Max Power Saving Mode"



Clear = "Clear"



GearNameL0 = "Auto"



GearNameL1 = "Turbo"



GearNameL2  = "High performance"



GearNameL3  = "Medium power saving"



GearNameL4  = "Max. power saving" 



Cancel = "Cancel"



OK = "OK"



CloseUnnecessaryPrograms = "Please close all  running programs and calibrate the EPU function."



CalibrateAfterSetting ="You need to run the calibration again to take your setting effect."



CalibrationBeforSetting = "Before setting to Auto Mode, you need to calibrate the EPU function."



CloseAllRunningPrograms = "Close all running programs before EPU calibration."



BackToDefault = "Due to the unstable adjustment, the EPU is automatically restored to its default setting."



ChangeSetting = "The system might become unstable after this setting." 



SureContinue = "Are you sure you want to continue?"



SetToHighPerformanceBeforeExit = "You are now exiting EPU, and EPU will automatically switch back to High Performance mode."



SureExit = "Are you sure you want to exit?"



CalibrateAfterSettingChanged ="You need to calibrate again after the CPU voltage or other voltage settings are changed."



TweakItConfirm = "The TweakIt function will be disabled when EPU set to Auto Mode, to enable TweakIt, please set to Turbo Mode!"



EnableDynamicPwm = "To run Auto Mode, EPU will adjust and restart the system to optimize the power management. Would you like to restart the system now?"



Yes = "Yes"



No = "No"



InformCalibration = "Close all running programs before calibrating the EPU function."



CalibratingWait ="Calibrating, please wait& "



RunCalibration = "Calibrate"



Mode = "Mode"



TweakItIsDisabled = "TweakIt is disabled. Set EPU to Turbo Mode before using TweakIt."



CannotLaunchOverclocking = "EPU cannot launch under system overclocking. Please restart your system."



AllowToolTip = "Allow Balloon ToolTip"



RunAtStartup = "Run at system startup"



Default = "Default"



CPUFrequency = "CPU Frequency"



vCoreDown = "vCore Voltage Downgrade"



DynamicPwm = "Dynamic Power Management"



OffHD ="Turn Off hard disks"



AINapIdleTime = "AI Nap Idle Time"



OffScreen = "Turn Off Screen"



After1min = "After 1 min"



Aftermins = "After %1 mins"



After1hour = "After 1 hour"



Afterhours = "After %1 hours"



Never = "Never"



Disable = "Disable"



Enable = "Enable"



AISuiteRequired = "ASUS AI Suite required"



VGAWindow = "No VGA detected. Please install a compatible VGA card or install and enable the ASUS SmartDoctor. For the list of compatible VGA cards, refer to" 



None = "None"



High = "High"



Extreme = "Extreme"



FanControl ="Fan Control"





KeepBIOSSetting = "Keep BIOS Setting"



Slow = "Slow"



Quiet = "Quite"



TuningCheck = "Before setting to the vCore downgrade voltage, you need to do stress test."



SureTuning = "Close all running programs before stress test."



TuningWait = "vCore Tuning, please waiting..."



StartTuning = "Start Tuning"

Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web5, load: 1.77