JMB36X RAID Driver Release History
---------------------------------------------------------------------------------------------------------------------------------
R1.17.54.02 (01/11/2010)
1. Fix issue:
a. Specific External HDD Box may get disappear and appear again when plug HDD with another port.
- Caused by the External Box may get re-link with this case.
- Modify driver to just re-initialize the disk with this case.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.54.01 (12/30/2009)
1. Add SSIDSVID
- Add 843F1043, 84401043 for ASUS
2. Fix Issue
a. Some PMP device may be identified as HDD on specific platforms.
- The link of the PMP may get lost during Reset procedure and then identify procedure may get problem.
- Add check for Link lost conditions during Device Identification.
3. Driver Modification
- Modify Driver Cache condition to not to effect Average Read performance.
4. Setup Program Modifcation
- Add Option to install RaidAP only when Controller is at Raid Mode.
- Add Package which uses new Setup Program for test.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.54.00 (12/16/2009)
1. Fix Issue:
a. Some PATA HDD may not be recognized correctly with specific PATA Cable.
- Caused by some Device Status may not be updated correctly to AlternateStatus when using this cable.
- Check Status in Command Register to avoid this issue.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.53.00 (11/23/2009)
1. Add SSIDSVID
2. Fix Issue
a. Fail to load driver during Install Windows 7/Vista if one PATA NEC DVD Recorder is connected to 36X.
- Caused by the DVD Recorder may keep BUSY after it reports Command Complete with specfic ATAPI commands.
Driver may fail to issue latter commands when it is still BUSY.
- Add checking BUSY and delay if this issue occurs.
b. Snapshot compare fail after resume from Sleep.
- Caused by OS may fail to record Disk Power Capability after boot up on specific platforms.
- Modify method to check and report Device Removable to avoid return Busy with
QueryCapabilities.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.52.02 (10/29/2009)
1. Fix Issue
a. OS may not shutdown properly on some P55 platform if create Raid with Intel SATA ports.
- Caused by ISR of JMB36X driver is called after MMIO is disabled.
Add checking to ignore ISR call if MMIO is not accessible.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.52.01 (10/28/2009)
1. Add SSIDSVID
---------------------------------------------------------------------------------------------------------------------------------
R1.17.52.00 (10/21/2009)
- Add checking for IDE Channel Swap case with Single Function IDE Mode.
- Add registry setting to inf file for WLK 1.5 Requirement.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.51.02 (10/09/2009)
- Modify sequence of handling PATA - ATAPI command 0x46 again for compatibility issue with LG PATA DVD Burner.
- Modify sequence of handling PATA - ATAPI command 0x5A to fix play DVD issue with Pioneer DVD-127D.
- Add CustomSetting Flag for setting RX Threshold for PMP compatibility issue.
- Update Setup Program for adding new setting flag.
- Update Setup Program of Gigabyte for RaidTool System Tray issue on Windows Vista and Windows 7.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.51.01 (10/01/2009)
- Modify to reset All PMP Child devices first before check status of each PMP Port.
To reduce time needed of enumerating PMP Ports.
- Modify to do retry if AHCI Port cannot get Link with Device correctly after resume from sleep.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.51.00 (09/23/2009)
- Modify to handle Smart Command by Interrupt.
- Modify to re-enumerate connected devices in thread after resume from sleep if no device is connected before sleep.
To reduce resume time needed if no device is connected.
- Implement supporting for 2363 PATA Controller at function 1.
- Modify sequence of handling PATA - ATAPI command 0x46 to avoid compatibility issue of some PATA Optical Devices.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.50.02 (08/11/2009)
- Modify Wait CI = 0 operation to only delay when CI != 0 to reduce time needed when handling PMP Port hotplug.
- Enlarge status checking time with ComReset and IDLE Command for some HDD may need more time to get ready after HDD Turn OFF and Wakeup.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.50.01 (08/06/2009)
- Fix issue that WD MyBook External SATA Disk may stop working after Turn Off Disk and Resume.
WD MyBook External Disk 1TB may need about 9 Seconds to become ready after resume.
Enlarge driver timeout time with the resume command.
- Add CacheParamter3 as SSD CacheDelay setting. (SSD is identified when MediaRotationRate is reported as 1)
- Modify driver to re-enumerate connected devices in RestartAdapter to avoid data access issue when
OS is installed on the connected disk.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.50.00 (07/29/2009)
- Fix issue that OS may not enter Sleep correctly when OS installed on JBOD created with specific disks.
- Fix issue that OS may not install driver of specifc SATA CD/DVD-Rom correctly when it is newly reported.
- Modify driver to always re-enumerate connected devices in Thread after resume from sleep.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.49.04 (07/17/09')
- Fix Load Driver Slow issue during Windows Vista Setup.
- Fix DVD-RW Burn fail issue happens with R1.17.49.00.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.49.01 (07/16/09')
- Fix BSOD issue if unexpected interrupt signals when driver is handling Smart Command.
- Fix enter S3/S4 slow issue when 2 PATA HDDs are connected.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.49.00 (07/13/09')
- Fix issue that driver may get BugCheck during resume from Sleep when PMP is connected.
- Modify reporting way of Disk VendorId and ProductId to avoid improper blank character issue.
- Implement Extra Request Timeout Detection and Recovery procedures.
- Fix issue that may not reboot after install driver with single function IDE mode if specific IDE CD-Rom is connected.
- Fix issue that driver may get access violation if both PCI functions are installed with JRaid.sys at multi-function case.
- Add Retry times of PMP Initialize because some PMP may need more time to get ready after Power ON.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.48.16 (06/25/09') (NotReady)
- Fix S1 resume issue on Specific platform.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.48.15 (06/15/09')
- Fix the issue that some disks which connected with PMP may get timeout-reset with first command after turn-off and resume.
- Add CacheParameter2 for Cache Delay Setting at 1.5G
---------------------------------------------------------------------------------------------------------------------------------
R1.17.48.14 (05/20/09')
- Modify the RAID API dll to fix the issue of creating RAID upon the disks which sizes are over 2TB.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.47.13 (05/18/09')
- Rebuild 1.17.47.11 with inf DriverVer Modified for Win7.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.48.13 (05/12/09')
- Fix the issue that RAID1 rebuiding is slow.
- Fix the issue that RAID1 failed to auto-resynch.
- Fix the issue that RAID AP won't update if removing one disk of RAID1.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.48.12 (05/07/09')
- Modify Condition to issue Standby Command with S3/S4.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.48.11 (05/06/09')
- Add CustomSetting Control Bit to issue Standby Command with S3/S4.
- Fix SONY Tape Device Identify issue.
- Add Flag Control for 353 BlueRay Emulate HDD device Patch to fix OS may delay about 6 seconds with Optical Device issue.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.48.10 (04/17/09')
- Fix IDE Optical Device may take long time to execute command issue.
- Add CustomizedSetting Flag to Control Toshiba TEC handling routines.
- For ExpressCard Product. Check if Adapter already removed when OS calls to Remove Device to avoid access failure.
- Fix issue that sometimes Disk may not be reported after Create/Modify Raid Type.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.47.12_ForHP (04/16/09')
- Rebuild with R1.17.47.11 with SSIDSVID added in inf for HP.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.48.09 (04/13/09')
- Add SSIDSVID 2A9C103C for HP
- Add SSIDSVID 025D1025, 025E1025 for Foxconn
- Add SSIDSVID 500F17FF for Inventec
- Fix incorrect Revision with eSata Disk Device issue.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.48.08 (04/02/09')
- Add Handling codes for DIPM.
- Report Disk with RemovableMedia if it is identified as JM SSD with RemovableMedia ID.
- Modify Delay Periods to fix driver may wait for unexpected long tim with PMP error cases.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.48.07 (03/19/09')
- Fix PMP HotPlug may Freeze System issue.
- Modify some Delay period values used in Thread to fix wait for unexpected long time issues.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.48.06 (03/16/09')
- Fix Handling Smart Command may Freeze System issue.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.48.05 (03/10/09')
- Fix the issue that hibernation failed with Thread Routine.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.48.04 (03/06/09')
- Fix the issue that Sony 300S blue-ray ODD is not detected sometimes in Windows when connected to JMB322. (Gigabyte)
- Fix the issue that creating JMB322 RAID failed sometimes after deleting matrix RAID.
- Fix the issue that some users report that there is a click sound & chkdsk error in warn reboot.
- Add option to disable issuing standby command when turning off HDD.
- Modify hotplug.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.47.11 (02/19/09')
- Fix the issue that IDE HDD is wrongly set as UDMA mode 2.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.47.10 (02/12/09')
- Fix the issue that hard disks are removed for unknown reasons sometimes.
- Fix the issue that DTM 1.3 "Reinstall With IO" failed on Windows 7.
- Fix the issue that disk error counter is not written to disk successfully.
- Fix the issue that creating RAID from existing disk results in BSOD.
- Fix the issue that hotplug failed sometimes.
- Add the option to disable SMART function.
- Fix the issue that using setup.ini to enable PMP RAID failed.
- Fix the issue that when SATA ODD is connected IDE disk will disappear after resuming from S3.
- Automatically resynchronizing RAID1 after three continuous errors. (only for Toshiba TEC)
- Add the option to support AAM.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.46.06 (01/14/09')
- Fix the issue that waking up disks makes mouse freeze.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.46.05 (01/13/09')
- W/r the issue that JMB351 blue-ray ODD enclosure which is simulated as hard disk needs more time to be ready.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.46.04 (12/30/08')
- RAID AP will rebuild RAID when there is a read/write error. (Toshiba TEC)
---------------------------------------------------------------------------------------------------------------------------------
R1.17.46.03 (12/29/08')
- Fix the SATA disk IPM issue.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.46.02 (12/26/08')
- Add "CacheParameter1" in setup.ini to adjust the burst read performance.
- Enable SATA disk IPM.
- Modify ATA_PASS_THROUGH for JMF60x.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.45.04 (12/18/08')
- Fix the issue that the RAID will disappear after creating RAID.
- Fix the issue when IS is right but TFD has errors. (Toshiba TEC)
- Fix some compiling erros when enable TOSHIBA_TEC.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.45.01 (12/16/08')
- Set disk to standby when shutting down. (Toshiba TEC)
- In Device Manager it leaves the drive listed with a yellow exclamation mark after safely removing the eSATA drive. (Seagate)
- Switching IDE/AHCI/RAID mode in BIOS results in BSOD. (Seagate)
---------------------------------------------------------------------------------------------------------------------------------
R1.17.45.00 (12/10/08')
- Adding HP subsystem vendor ID 0x2A86103C. (HP)
- Show the original HDD/ODD model name in device manager for eSATA devices. (not show SATA*****) (Seagate)
- Add the option to disable eSATA disk write cache in disk policy. (Seagate)
---------------------------------------------------------------------------------------------------------------------------------
R1.17.44.05 (11/21/08')
- Fix the issue that PMP disks frozen state are not set after resuming from S3.
- Fix the issue that PMP disks has an exclamation mark in device manager after resuming from S3.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.44.04 (11/20/08')
- Not to support PMP RAID.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.44.03 (11/20/08')
- Fix the issue that Win2000 BSOD when resuming from S1. (Toshiba TEC)
- Fix the issue that JMB368 will reboot when entering S3.
- Fix the issue that RAID rebuilding will not stop even if the disk is removed.
- Fix the issue that HotPlug in S3/S4 failed. (Flex. & Gigabyte)
---------------------------------------------------------------------------------------------------------------------------------
R1.17.44.02 (11/14/08')
- Adding Foxconn subsystem vendor ID 0x01981025, 0x01711025, 0x01701025.
- Fix the issue that RAID rebuilding is slow.
- Fix the issue that hot-plugging in the 2 RAID SATA disks quickly, the disk detection time is long.
-----------------------------------------------------------------
R1.17.43.06 (11/14/08')
- Modify the setup title name to "JMicron JMB36X Driver" (old : "JMB36X Raid Configurer").
- Customize the RAID AP show state at system boot time.
(a) "RaidAPShowStateAtSysBoot" value: bit 0 -> customize this feature with setup.ini; bit 1 -> Show RAID AP window when system boot
e.g. RaidAPShowStateAtSysBoot = 0 -> ignore/disable this feature, customize it with option ROM
RaidAPShowStateAtSysBoot = 3 -> customize this feature with setup.ini and show RAID AP window when system boot
RaidAPShowStateAtSysBoot = 2 -> customize this feature with setup.ini and DO NOT show RAID AP window when system boot
- Fix the conflict issue between JMB36x package setup and VIA 1708S audio AP setup under vista OS. (Via audio AP setup program use the out-of-dated difxapi Dll file)
- Fix the uninstall issue of popup a message dialog when selecting reboot after doing uninstallation in vista OS.
----------------------
R1.17.42.10_WHQL (11/04/08')
- Modify the setup title name to "JMicron JMB36X Driver" (old : "JMB36X Raid Configurer").
- Fix the conflict issue between JMB363 setup package and VIA audio AP setup.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.43.05 (11/03/08')
- Fix the issue that system event log has error #117 in Vista.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.43.04 (10/31/08')
- Burning disc sometimes failed with some IDE ODDs on some platforms.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.43.03 (10/30/08')
- Snake TB-400S PMP hotplug failed.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.43.02 (10/30/08')
- Fix the issue that hard disk becomes write-protected sometimes on the platform equipped with 4GB DRAM.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.43.01 (10/21/08')
- Support JMB368 in driver and inf.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.43.00 (10/20/08')
- Fix the issue that JMB325 RAID-changing may fail sometimes.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.42.09 (10/14/08')
- Provide a key to customize the value of "UseBigCache". (WR a hiberniation issue)
---------------------------------------------------------------------------------------------------------------------------------
R1.17.42.08 (10/01/08')
- Fix the issue that JMB322 RAID-changing may fail when OS is on JMB36x IDE disk. (MSI)
---------------------------------------------------------------------------------------------------------------------------------
R1.17.42.07 (09/26/08')
- Fix the issue that hot-insert two disks continuously and quickly but only one disk is detected.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.42.06 (09/23/08')
- Fix the issue that JMB322 create/delete RAID sometimes fails, especially with two JMB322 controllers.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.42.04 (09/18/08')
- Fix the issue that fail to burn disc of UDF format. (End User)
- Fix the issue that fail to erase disc.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.42.03 (09/17/08')
- Solve the issue that the performance is poor when testing two disks at the same time.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.42.02 (09/16/08')
- Solve the issue that the performance of sequential 2K r/w is poor.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.42.01 (09/16/08')
- Fail to install Vista with the RAID of two eSATA enclosures or resume from S3 late or fail to resume from S3. (ASUS P5Q-M Delux)
- Hitachi HDD which is connected to eSATA port easily failed with SDStress. (ASUS P5Q-M Delux)
---------------------------------------------------------------------------------------------------------------------------------
R1.17.42.00 (09/10/08')
- Fix the issue that OS on RAID of two eSATA enclosures wakes up late.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.41.05 (09/01/08')
- Fix the issue that broken JMB322 RAID0 doesn't show forbidden to access in disk manager.
- Add MSI SSID/SSVID 0x75201462.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.41.04 (08/29/08')
- Using AP to create/delete JMB322(WD7500AAKS+HDP725050GLA360) RAID, the disk disappears sometimes.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.41.03 (08/29/08')
- Fix the issue that Hitachi HDS721010KLA330 1TB hard disk disappears after resuming from S3.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.41.02 (08/28/08')
R1.17.41.01 (08/27/08')
R1.17.41.00 (08/27/08')
- Fix the issue that Winthrax sometimes has error after resuming from S3 with JMB363+JMB322.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.40.05 (08/22/08')
- Fix the issue that PMP hot plug failed when turning on/off the power of PMP.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.40.04 (08/21/08')
- Fix the issue that creating/deleting RAID with JMB322 RAID AP sometimes makes disks lost.
- Fix the issue that mouse is frozen for several seconds when hot-plugging the PMP child port disk.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.40.03 (08/14/08')
- Fix the issue that to create a RAID without including JMB325 port 0 disk failed.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.40.02 (08/12/08')
- Fix the issue that JMB322 broken RAID encounters comreset always.
- Fix the issue that creating/deleting RAID with JMB322 RAID AP sometimes makes disks lost.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.40.01 (08/12/08')
- Improve the read performance.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.40.00/R1.17.40.00.368 (07/25/08')
- Support two devices for JMB368.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.39.07 (07/22/08')
- IDE disks are wrongly set as removable.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.39.06 (07/15/08')
- To w/r the GA-EP45-DS5 SiI5723 HDD LED issue.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.39.05 (07/09/08')
- Removable icon doesn't show for HDD.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.39.04 (07/04/08')
- Hot-plugging JMB336 ODD enclosure (HP Voodoo NB) has "!" sometimes.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.39.03 (07/03/08')
- The hotplug of two SATA ODD has problem.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.39.02 (06/27/08')
- PMP root port hot-plug failed.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.39.01 (06/27/08')
- Burning disc failed.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.38.05 (06/17/08')
- Pass the WLK 1.2 "Storage Query Property" test.
- The "safely remove device" disappears after creating PMP RAID.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.38.04 (06/12/08')
- Hot plug too fast will make the system hang up.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.38.03 (06/11/08')
- External
- Issue Correction
- W/r the eject button of JMB336 ODD enclosure for HP Voodoo NB.
- Add "Bustype" in inf to pass WLK 1.2 "Storage Query Property" test.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.38.02 (05/30/08')
- External
- Issue Correction
- Device manager shows a "!" after hot-plugging an ODD. (HP Voodoo NB)
- Work around the issue that S3/S4 will crash if OS is installed in disk connected to eSATA port. (ASUS iCH10)
- Internal
- Issue Correction
- It needs more than 15 sec to detect a plug-in ODD.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.38.01 (05/23/08')
- External
- Note
- Adding subsystem vendor ID 0x90081071 for Mitac.
- Issue Correction
- CPU utilization is abnormally high when WD Mybook 1TB spins down.
- Some systems can't be shut down if ODD is connected.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.38.00 (05/09/08')
- External
- Note
- Adding subsystem vendor ID 0x83521043 for ASUS.
- Only modified inf. Driver is not changed.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.37.01 (05/08/08')
- External
- Note
- Adding subsystem vendor ID 0x02821028.
- Adding the disk error count for Toshiba TEC.
- Issue Correction
- CPU utilization is abnormally high.
- Not all SiI4723 PMP HDD can be detected after turning on its power.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.36.00 (04/30/08')
- External
- Note
- It's a special revision to w/r SiI5723 on GA-EP45-DS5.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.35.02 (04/30/08')
- Internal
- Note
- Change the hot-plug detecting method to w/r the issue that ScsiPortNotification doesn't work on some platforms.
- Issue Correction
- Fix the driver uninstallation issues when the OS disk is connected to our JMicron controller. (start from R1.17.34WHQL, R1.17.35.02 and later version)
---------------------------------------------------------------------------------------------------------------------------------
R1.17.35.00 (04/21/08')
- External
- Issue Correction
- System lags when accessing the ODD without a disc in.
- Internal
- Issue Correction
- Turning on the power of PMP, not all disks are detected.
- Note
- Enlarging the data transfer length per command to 128KB.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.34.03 (04/17/08')
- External
- Issue Correction
- System lags or pends for several seconds when turning on the power of the hard disk connected to JMB363 SATA port.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.34.02 (04/16/08')
- External
- Note
- Adding MSI subsystem vendor ID 0x73761462.
- Issue Correction
- System will pend for 3~5 sec when turning on the power of hard disks.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.34.01 (04/15/08')
- External
- Issue Correction
- System will pend for 3~5 sec when turning on the power of hard disks.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.34.00 (04/08/08')
- External
- Issue Correction
- System pends when connecting Silicon Image easy RAID. (Gigabyte)
---------------------------------------------------------------------------------------------------------------------------------
R1.17.33.03 (04/03/08')
- External
- Issue Correction
- ASUS NB crashed (blue screen) in Vista S3 sometimes.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.33.02 (04/02/08')
- Internal
- Issue Correction
- The system is abnormal when hot-plugging one hdd of the RAID1 OS.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.33.01 (03/27/08')
- Internal
- Note
- Improve the error handling.
- Change the port80 message.
- Change the function setting disk to frozen state.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.33.00 (03/19/08')
- External
- Issue Correction
- System will pend for 3~5 sec when turning on the power of hard disks.
- Raid AP is unable to detect the raid device in Win2003 R2 SP2 on some platforms. (Modify the DeviceIO buffer size to 64K)
---------------------------------------------------------------------------------------------------------------------------------
R1.17.32.06 (02/21/08')
- External
- Issue Correction
- Raid AP will mistakenly detect multiple SCSI controllers with new ASUS drivers on nVidia C73 platform.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.32.05 (02/14/08')
- External
- Issue Correction
- JMB360 chip rev. 2 will hang in disk accessing on ASRock K10N750SLI-WiFi motherboard.
- Note
- Append a customized key "DisableRaid0" to disable Raid0 in setup.ini. Modify setup program (JMicron normal package) and Raid AP DLL to support this feature.
("DisableRaid0=1" indicate to disable Raid 0, default is set to zero and indicate to support Raid0)
- Internal
- Note
- Disable JMB360 NCQ command.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.32.04 (02/05/08')
- External
- Issue Correction
- The HDD is not frozon after S3 on ASUS motherboards.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.32.03 (01/29/08')
- External
- Issue Correction
- Accessing failed with HDD or RAID size >= 1TB and < 2TB.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.32.02 (01/25/08')
- External
- Issue Correction
- RAID1 of 2 Sandisk Extreme CF cards always show not synch after rebooting.
- Pushing Power DVD 7.3 play button to play DVD in Pioneer IDE DVD ROM (DVD-127D) will have a delay of about 10 sec.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.28.00.368.Sandisk (01/16/08')
- External
- Note
- It's a special revision to install the driver for Sandisk Vaulter disk (JMB368 Flash disk).
---------------------------------------------------------------------------------------------------------------------------------
R1.17.32.01 (01/15/08')
- External
- Issue Correction
- 2 Sandisk Extreme III CF cards are connected, they failed to be accessed after S3.
- Power DVD 7.3 failed with Pioneer IDE DVD ROM (DVD-127D).
- Internal
- Issue Correction
- Blue Screen in hot-plug PMP if OS HDD is connected to JMB363.
- The HDD is not turned off if the power scheme is set as "turn off hard disks after x mins".
---------------------------------------------------------------------------------------------------------------------------------
R1.17.32.00 (01/04/08')
- External
- Issue Correction
- Samsung HM160HI HDD r/w failed.
- Hot plug failed with JMB336.
- HdTach average read is slower in new driver with WD HDD.
- After resuming from sleeping, failing to access IDE HDD connected to JMB363 w/o option rom.
- Internal
- Issue Correction
- JMB330 r/w failed after hot plug or S3.
- JMB325 is recognized as HDD when turning on its power.
- Setting the registers for better SATA connection of JMB36x version C0.
- PMP RAID is not marked as degrade when removing members and turning on the PMP.
- Note
- Adding w/r - when resetting PMP child port (port reset), the D2H signature FIS is dropped by h/w.
- Adding for JMB373 - when resetting PMP child port (port reset), the D2H signature FIS is not dropped by h/w.
- Re-enumerating PMP after comreset.
- Read mirror disk when r/w error.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.31.01 (12/04/07')
- Internal
- Issue Correction
- DCT "Common Scenario" test failed in Win2003 x64.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.31.00 (11/26/07')
- Internal
- Note
- Setting the registers for better SATA connection.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.30.01 (11/20/07')
- External
- Issue Correction
- HdTach average read is slower in new driver with WD HDD.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.30.00 (11/19/07')
- External
- Issue Correction
- Supporting hard disks exceeding 2TB size.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.29.03 (11/19/07')
- External
- Issue Correction
- Fix an installation issues to avoid Intel Graphic card driver uninstallation fail in vista 32/64 bit OS.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.29.02 (11/06/07')
- Internal
- Issue Correction
- DCT "Common Scenario" test failed in Win2003 x64.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.29.01 (10/30/07')
- External
- Note
- Modify Driver, raid application, setup program to support the "Disable NCQ" option for Asrock, no matter in AHCI, IDE or raid mode.
Please customize the "SupportDisableNCQ" key in setup.ini to support the function of disable NCQ. (only apply for Normal package, not including SiS and Gigabyte package )
(if SupportDisableNCQ = 1, support "Disable NCQ"; otherwise NOT support. Default is 0, NOT support)
- Raid Application will show all disk information including ODD info in AHCI and IDE mode. (only apply for Normal package, not including SiS and Gigabyte package )
- Issue Correction
- WD "mybook" write is slow.
- Modify setup program to remove the dialog of selecting "Add-on card" or "On-board" card during installation.
- Internal
- Issue Correction
- DCT "Common Scenario" test failed in Win2003 x64.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.29.00 (10/15/07')
- External
- Note
- To be able to enable/disable "Safely Remove Hardware" in setup.ini.
(CustomizedSetting2 bit 3 - (1/0) enable/disable the capability to set "Safely Remove Hardware" in setup.ini.
CustomizedSetting2 bit 4 - (0/1) SATA port 0 is/isn't eSATA.
CustomizedSetting2 bit 5 - (0/1) SATA port 1 is/isn't eSATA.)
---------------------------------------------------------------------------------------------------------------------------------
R1.17.28.00.368 (10/12/07')
- External
- Note
- It's a special revision to install the driver for JMB368.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.28.00 (09/29/07')
- External
- Issue Correction
- CCTest failed when PMP was connected. (Gigabyte GA-X38T-DQ6)
- When 2 Sandisk CF cards are connected and running RAID AP, the system is abnormal. (ASUS)
---------------------------------------------------------------------------------------------------------------------------------
R1.17.27.01 (09/27/07')
- External
- Issue Correction
- CCTest failed when PMP was connected. (Gigabyte GA-X38T-DQ6)
- Internal
- Issue Correction
- SMART & Identify command failed with PMP HDD.
- RAID0 disk error-checking of disk manager makes the system delay in Vista.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.27.00 (09/26/07')
R1.17.26.07 (09/21/07')
R1.17.26.06 (09/19/07')
- External
- Issue Correction
- CCTest failed when PMP was connected. (Gigabyte GA-X38T-DQ6)
---------------------------------------------------------------------------------------------------------------------------------
R1.17.26.05 (09/17/07')
- External
- Issue Correction
- Sdstress can't run when IDE HDD and ODD are connected. (Foxconn P35AP-S)
- When 2 CF cards were connected, the access failed.
- CCTest failed when PMP was connected. (Gigabyte GA-X38T-DQ6)
---------------------------------------------------------------------------------------------------------------------------------
R1.17.26.04 (09/13/07')
- External
- Issue Correction
- OS in JMB363 easily crashed in booting with Ati Radeon HD 2400 PRO (driver 7-9_xp32_dd_ccc_wdm_enu_52443). (Foxconn)
---------------------------------------------------------------------------------------------------------------------------------
R1.17.26.03 (09/11/07')
- Internal
- Issue Correction
- When PATA HDD is connected, running RAID AP will make the CPU usage of Windows task manager rises a lot and
doesn't drop even if the AP is closed.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.26.02 (09/10/07')
- External
- Note
- Raid Ap could only show disk info for non-Raid mode by customizing the value of "ShowDiskInfoForNonRaidMode" in setup.ini. (only apply for normal package)
(If "ShowDiskInfoForNonRaidMode" = 1, enable to show disk info for non-Raid mode. Default is 0)
- Issue Correction
- Turning on the power of HDS725050KLA360(500G) in OS, the HDD failed to be detected.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.26.01 (09/06/07')
- Internal
- Issue Correction
- Turning on the power or plugging in PMP RAID1/10, then the RAID AP will show RAID not synch.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.26.00 (09/04/07')
- External
- Issue Correction
Turning on the power of Marvell's PMP in OS, the HDD failed to be detected.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.25.02 (08/30/07')
- External
- Note
- Enable the IDE access for cards without option rom (Need not to set "CustomizedSetting2").
- Adding ASUS subsystem vendor ID 0x17681043.
- Issue Correction
- JMB336 encloure failed with SdStress test (Foxconn dual eSATA).
- The security status of JMB368 HDD is still not frozen even if BIOS sets it to frozen status.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.25.01 (08/29/07')
- Internal
- Issue Correction
- Installing OS with JMB363 ODD will make the system crash.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.25.00 (08/29/07')
- External
- Note
- Removing the NB HDD clicking patch since BIOS has already worked around it.
- After creating raid0/10/JBOD from an existing disk, the raid application will show the message about the extra unallocated disk space.(remove the button of invoking Disk management dialog for doing disk partition/format)
(Apply for SiS, Gigabyte and Jmicron packages)
- Set "CustomizedSetting2" bit 3 to 1 (0x08) to enable the IDE access for cards without option rom.
- Issue Correction
- JMB336 encloure accesss failed (Foxconn dual eSATA).
---------------------------------------------------------------------------------------------------------------------------------
R1.17.20.05 (08/23/07')
- External
- Note
- After creating raid0/10/JBOD from an existing disk, the raid application will show the message about the extra unallocated disk space.
(Based on R1.17.20WHQL driver, only modify Raid AP)
---------------------------------------------------------------------------------------------------------------------------------
R1.17.20.04 (08/20/07')
- External
- Note
- After creating raid0/10/JBOD from an existing disk, the raid application will show the message about the extra unallocated disk space and also provide a button to invoke Disk management dialog for doing partition/format.
(Based on R1.17.20WHQL driver, only modify Raid AP)
---------------------------------------------------------------------------------------------------------------------------------
R1.17.24.06 (08/21/07')
R1.17.24.05 (08/20/07')
- External
- Issue Correction
- Hotplug device in S3/S4 will NOT detect device correctly after resuming from S3/S4 even turning on the feature of Sata device detection (CustomizedSetting2=1) after S3/S4 wake up.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.24.04 (08/19/07')
- External
- Issue Correction
- The JMB362 notebook HDD clicks in S3/S4/shutdown.
- Modify Raid application due to disk structure update.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.24.03 (08/15/07')
- Internal
- Issue Correction
- [Driver] Shorten the phy detection time of resuming from S3 to 2.2s when no device is connected.
- [Driver] Under WinXP Pro 64Bit or WinVista Ultimate 64Bit, there occurs a bluescreen during windows startup when connecting PMP.
- [Driver] There is some noise from 2.5-inch HDD (Asus NB with JMB362) when entering sleeping mode.
- [AP] After creating JBOD from an existing disk, the raid doesn't appear in device manager.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.24.02 (08/09/07')
- Internal
- Issue Correction
- [Driver] Shorten the phy detection time of resuming from S3 when no device is connected.
- [AP] Plug-in/ plug-out a HDD quickly without waiting the hotplug info dialog close, multiple hotplug dialogs might be shown and could be closed.
- [AP] After creating raid0/10/JBOD from an existing disk, the raid application will show the message about the extra unallocated disk space and also provide a button to invoke Disk management dialog for doing partition/format.
- [AP] Delete MBR and assign random signature for all member disks when removing raid0/10/JBOD (except Raid1). Avoid the fail issue of installing Vista OS upon those disks.
- [AP] Under multiple adapters case, if plug-out all HDDs on one controller, our raid application will disable the controller selection button on the toolbar and show the correct disk info of the controller which has HDDs.
- [AP] Under multiple adapters case, hotplug the HDDs among controllers will show the wrong hotplug disk info.
- [Driver and AP] During rebuilding/resynching/creating raid upon PMP HDDs, hotplug any PMP HDDs will stop the process and our raid application will show messages. (limitation)
---------------------------------------------------------------------------------------------------------------------------------
R1.17.23.00 (07/29/07')
- Internal
- Issue Correction
- CPU utilization increases 40~50% when resuming from S4 and one of disk is PATA disk.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.24.01 (07/26/07')
- Internal
- Issue Correction
- Doing Full format for Raid which includes pata disks will cause system hang.
- Hotplug a port-multiplier at one time and system will hang.
- Under multi-adapters case, when hotplug a HDD or PMP HDDs from different adapter, AP will show the error message and hang.
- Hotplug all PMP HDDs at one time, the hotplug information will be truncated due to the limited space in the hotplug dialog.
(Append the scrollbar to the hotplug information box)
- Avoiding multiple message dialogs appear at the same time when hotplug occurs, modify the hotplug information window to be closed automatically after being displayed for a certain time.
(a) When hotplug one member disk of the rebuilding raid, the dialog of showing rebuilding fail will appear. Meanwhile, the hotplug information dialog will appear, too.
(b) Using multithread to fix the above issues.
- Modify the button string in the raid removal dialog which will appear when user want to remove the OS raid.
- When more than one raid need resynching (even from multiple adapters), AP will only show one resynching dialog for users at one time.
- Under multiple adapters case, if user reject doing the resynching raid which is from second adapter, the resynching dialog will also pop up for user to do resynching when AP is opened next time.
- CPU utilization increases 40~50% when resuming from S4 and one of disk is PATA disk.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.24.00 (07/12/07')
- Internal
- Note
- The following processes could be done continously even after resuming from sudden suspension such as system shut down or closing the raid application during the process.
(a) The process of creating raid 1 and raid 10 from an existing disk (reserve the data of the existing disk)
(b) The process of rebuilding new raid (Raid 1/10) (add a new disk to rebuild the degraded raid)
(c) The process of resynching raid (Raid 1/10) (resynchronize the data to the once-unplugged disk)
- Raid 10 is active and accessable when all the following conditions are met.
(a) The number of the existing member disks is at least half of total number of raid disks
(b) At least all stripe disks should exist to keep the data intact. Any mirror disks could be unplugged.
(c) No conflict pairs (Both mirror disks are once unplugged)
- The above processes will be stopped when unplugging any member disks of the rebuilding/resynching/creating raid.
- The rebuilding /resynching process of Raid 10 could be done as long as its relative mirror disk exist. But if the rebuilding/resynching process start running, it will be stopped when any member disks are unplugged.
- The process of creating new Raid 1/10 from an existing disk could be done even after some member disks are once unplugged and now plugged in again. In short, the unplugged status will not be recorded as Async during the creating process.
- Modify the raid application and driver (Based on R1.17.21.01 driver)
---------------------------------------------------------------------------------------------------------------------------------
R1.17.22.02 (07/25/07')
- External
- Note
- In setup.ini, if CustomizedSetting2 bit 2 is 1, then not to down to SATA GEN 1 (Gigabyte).
---------------------------------------------------------------------------------------------------------------------------------
R1.17.22.01 (07/24/07')
- External
- Issue Correction
- Samsung HD400LJ HDD has NCQ issue, so not to issue NCQ command to this HDD.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.22.00 (07/23/07')
- External
- Note
- Not to scan the device connected to SATA port 1 of JMB361.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.21.02 (07/05/07')
- Internal
- Note
- Supporting JMB373.
- Issue Correction
- HDD is not really locked/unlocked when using AP to lock/unlock it.
- Power down PMP then power on it, not all PMP HDD can be recongnized.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.21.01 (06/30/07')
- Internal
- Issue Correction
- DTM failed.
- SDStress failed with 2M cable on Maxtor DiamondMax 20 STM3160811AS.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.21.00 (06/27/07')
- External
- Note
- Adding Foxconn subsystem vendor ID 0x0DF8105B.
- Issue Correction
- Hot plug failed after resuming from S3.
- Internal
- Note
- Changing the error controlling mechanism.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.20.03 (06/13/07')
- Internal
- Note
- Supporting HDD security lock.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.20.02 (06/12/07')
- External
- Issue Correction
- Sometimes not all PMP disks can be detected with Gigabyte eSATA.
- Shorten the PMP detection time from more than 10 seconds to 6 seconds.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.20.01 (06/08/07')
- Internal
- Note
- Adding an application to workaround the device hotplug issue after resuming from S3. (Only for add-on card or Express card)
(Provide a dialog for users to choose "Add-on card" or "on-board controller" during installation.)
(The patched application should be run with administrator right at system boot on Vista OS so we install a special service to launch it and avoid the appearance of the "Grant administrator right" dialog.)
---------------------------------------------------------------------------------------------------------------------------------
R1.17.20.00 (06/02/07')
- External
- Note
- Adding Quanta subsystem vendor ID 0x059317FF.
- Issue Correction
- Hot plugging eSATA PMP failed in Gigabyte platform.
- Internal
- Note
- Removing JMB368 device ID from driver & inf to avoid conflicting with JMB38x driver.
- Issue Correction
- Set "UseBigUnCache" to 1 in the inf of floppy makes RAID0 OS crash.
- Access failed for SATA devices (like JMB330+CF) that only support multi-word DMA.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.19.03 (05/25/07')
- Internal
- Note
- When the Raid Application is running and hotplug all hdds but still keep ATAPI device connected, the raid application will show message and close the application.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.19.02 (05/24/07')
- Internal
- Note
- Adding cache parameters in setup.ini for AE to tune the HdTach burst read performance.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.19.01 (05/22/07')
- Internal
- Issue Correction
- HdTune & DriveLed failed with S.M.A.R.T.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.19.00 (05/21/07')
- External
- Note
- Supporting S.M.A.R.T. commands.
- Adding Abit subsystem vendor ID 0xF100147B.
- Issue Correction
- Benq 16x DVD ROM disappears after device rescanning.
- Raid Application can be opened when only ATAPI device is connected.
- Internal
- Note
- Setting UseBigUnCache to 1 in inf file.
- Changing the io control code in raidapi.h.
- Issue Correction
- Data accessing in LBA28 disk will fail if driver is installed with setup program (UseBigUnCache is set to 1).
(It's a side effect of last revision.)
---------------------------------------------------------------------------------------------------------------------------------
R1.17.18.07 (05/09/07')
- Note
- Adding Foxconn subsystem vendor ID 0x0CE6105B.
- Issue Correction
- Hibernation crashed.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.18.06 (05/08/07')
- Note
- Only modifying txtsetup.oem for Vista. Driver & AP are not changed.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.18.05 (05/04/07')
- Note
- Adding SiS vendor/device ID in INF file and driver.
- Support Installation and uninstallation for SiS VID and DID
(Modify xInsDrv.dll, xInsD64.dll, xLHDrv.dll, xLHD64.dll, installshield program for SIS package)
- (OnBoard multi-funtion (0101/0104) + single IDE (0101) Add-On Card case) When user select to install our JMicron standard IDE driver under windows Vista, the setup program will only install JMicron standard IDE driver for Single 0101 card.
(Multi-0101 card will not be updated with JMicron standard IDE driver.)
- Issue Correction
- OnBoard multi-funtion (0101/0104) + single IDE (0101) Add-On Card, Raid AP can't be opened. It will show "JMB36x Raid configurer tool doesn't support ACHI or IDE mole! It only supports Raid mode."
- The toolbar button of "controller selection" in Raid AP is only enable when more than one raid (0104) controllers are connected.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.18.04 (04/27/07')
- Issue Correction
- Win2000 crashed.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.18.03 (04/27/07')
- Note
- Removing the "Safely Remove Hardware" function from filter driver (jgogo.sys) to miniport driver and deleting the filter driver.
- Supporting both multi-function and multi-adapter (installation/uninstallation and driver) at the same time (except Win2000).
---------------------------------------------------------------------------------------------------------------------------------
R1.17.18.02 (04/18/07')
- Note
- Change txtsetup.oem format.
- The write performance increased.
- Issue Correction
- HdTach average write performance is bad in RAID10.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.17.01 (04/17/07')
- Note
- No matter user selects Raid driver or AHCI driver when installing OS (WinXP/2003) by pressing F6 to load driver, the driver is still properly loaded and OS is also installed successfully.
(This avoid users from selecting the wrong driver for the controller and it causes OS installation fail.)
- Modify floppy folder, txtsetup.oem and setup program. (Based on 1.17.17WHQL driver)
---------------------------------------------------------------------------------------------------------------------------------
R1.17.18.01 (04/17/07')
- Note
- When OS is installed on JMicron disks (or raid), uninstalling our Jmicron driver (via our uninstallation program in control panel) is rejected and also show the warning message to remind users.
- Removing the raid on which the boot OS resides is rejected in our Raid AP and it will show the warning message to remind users.
- When creating new raid, the OS disk will not be selected for building the new raid.
- When creating raid from existing disk, the OS disk will not be selected to be the destination disk.
- When rebuilding raid, the OS disk will not be selected to be the destination disk.
(the above features apply for all packages (Normal/SiS/Gigabyte)
---------------------------------------------------------------------------------------------------------------------------------
R1.17.18.00 (04/14/07')
- Issue Correction
- HDTach burst read has a performance down with JMB360 notebook.
- HDTach burst read has a performance down with a hot-inserted disk.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.17.00 (04/11/07')
- Note
- Support JMB368 express card with CF card (uDMA mode only), including the feature of CF card hot plug.
- Issue Correction
- SAMSUMG SATA HDD SP2504G with enclosure will pend (need to degrade to 1.5G).
---------------------------------------------------------------------------------------------------------------------------------
R1.17.16.00 (04/03/07')
- Note
- Support JMB368 scsi miniport driver for CF card (uDMA mode only), including the feature of CF card hot plug.
- Issue Correction
- In Vista, playing music has noise or delay when disk write cache is enabled but advanced disk performance is disabled.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.15.01 (03/28/07')
- Issue Correction
- When hotplug non-Raid HDDs, raid application will not popup the dialog of showing HDD hotplug information.
- During the process of rebuilding/resynching raid or creating raid from existing raid, raid AP doesn't handle the hotplug event and doesn't update the UI for the latest disk info at once.
(Handle multi-thread sync issues: rebuilding thread, hotplug polling thread, main UI thread. Modify xRaidAPI.dll and xRaidsetup.exe)
---------------------------------------------------------------------------------------------------------------------------------
R1.17.15.00 (03/24/07')
- Note
- Only inf changed.
- Issue Correction
- Conflicting with Vista in-box bluetooth driver (bthport.sys).
---------------------------------------------------------------------------------------------------------------------------------
R1.17.14.03 (03/23/07')
- Issue Correction
- IDE 40-pin cable failed.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.14.02 (03/21/07')
- Note
- Removing all "JM" and "JMicron" strings (filename and INF file content) in the driver package and replace them with the general filenames.
This is SiS request but we apply it to all customers' packages.
The following setup programs and raid application are needed to be modified for the above SiS requests.
(a) IDEDrvSetup.exe, xInsIDE.exe, xIDE64Setup.exe, xIDESetup.exe, xInsDrv.dll, xInsD64.dll, xLHDrv.dll, xLHD64.dll, xLink.exe
(b) xRaidSetup.exe, xRaidApi.dll and bitmap file (JMLayout.bmp)
(c) Installshield installation/uninstallation program
(d) INF file content (sraid_i.inf) and txtsetup.oem
- Issue Correction
- Uninstallation program failed to remove JMicron's OEMx.inf when using the classcode INF file (in floppy32 or floppy64) to install driver.
- During the raid rebuilding process, hotplug the SATA HDD which is NOT the member disk of the rebuilding raid will also make the rebuilding process fail.
- During the raid rebuilding process, hotplug the rebuilding SATA HDD will cause the incorrect disk info and is NOT updated properly. (the hotplug interrupt handler is not invoked)
- When hotplug the rebuilding SATA HDD, raid application will not popup the dialog of showing HDD hotplug information.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.14.01 (03/17/07')
- Note
- Support disk write cache for RAID.
- Changing manufacturer string for SiS in inf file.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.14.00 (03/16/07')
- Note
- Merging 32-bit inf file with 64-bit inf files.
- Be able to install driver even if the SSID is not in inf file.
- Adding JMB37x device ID in driver and inf files.
- Adding ASUS subsystem vendor ID 0x16D81043.
- Adding ABIT subsystem vendor ID 0x1083147B, 0x108A147B, 0x108B147B.
- Issue Correction
- Disk write cache failed to be enabled.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.13.02 (03/16/07')
- Note
- Modify SiS INF files and setup program for displaying "Silicon Integrated Systems Corp." in "Provider" and "Manufaturer items in the device properties dialog.
(Only SiS package is involved)
- Replace the original folder name ("JM") of the following setup programs and raid application with a general folder name ("RaidTool").
The following setup programs and raid application are needed to be modified for the above SiS requests.
(a) IDEDrvSetup.exe, JMInsIDE.exe, JMIDE64Setup.exe, JMIDESetup.exe, JMInsDrv.dll, JMInsD64.dll, JMLink.exe
(b) JMRaidSetup.exe
(c) Installshield setup program
---------------------------------------------------------------------------------------------------------------------------------
R1.17.13.01 (02/16/07')
- Note
- Adding Abit subsystem vendor ID 0x1083147B.
- Adding JMB37x device id mini-ide inf files.
- Customize the Raid AP installation for JMB36X (except JMB360) with the item "DisableRaidAPSetup" in setup.ini.
(Default is 0, indicate to "Support" Raid AP installation)
- Modify Gigabyte and SiS setup package to support all customized features provided in ASUS normal package, such as "DisableIDESetup", "DisableRaidAPForJMB360" and "DisableRaidAPSetup".
---------------------------------------------------------------------------------------------------------------------------------
R1.17.13.00 (02/12/07')
- Note
- W/r the ESD issue.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.12.05 (02/08/07')
- Note
- Adding JMB373 device ID in driver (not in inf).
- Issue Correction
- In some case RAID0 rebuilding failed in about 90%.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.12.04 (02/07/07')
- Issue Correction
- Sometimes the system is pending when RAID0 rebuilding finished 100%.
(set targetID when handling "remap_end" deviceIOcontrol function in ISR)
- Fail to reboot when shut down from creating raid 0% from the existing disk.
(OS might access the area which is partly migrated to other disk (stripe) and is partly located at the non-migrated area)
---------------------------------------------------------------------------------------------------------------------------------
R1.17.12.03 (02/07/07')
- Issue Correction
- Maxtor 80G HDD "DiamondMax 10 / Model:6V080E0" failed to be detected.
- Note
- Support installation and uninstallation for all vendors whose product ID and vender ID are matched even their subsystem ID are not listed in the INF file.
(Modify installshield setup program to use "jraid2_i.inf" as the default INF file in installing)
- Don't show the toolbar button of remove raid when the registry key "DisableRemoveRaid" is set to 1.
(This feature only apply to the normal release package. SiS and Gigabyte package just disable the remove raid button when "DisableRemoveRaid" is set to 1)
---------------------------------------------------------------------------------------------------------------------------------
R1.17.12.02 (02/06/07')
- Note
- Modify Raid AP underlying DLL (JMRaidAPI.dll) and driver to make the size of new raid (Raid0/1/10/JBOD) be the multiple of 128K and keep the metadata Range2 in sector unit.
(If the raid size is not the the multiple of 128K, driver will keep the raid size and consider backward compatibility)
---------------------------------------------------------------------------------------------------------------------------------
R1.17.12.01 (02/03/07')
- Issue Correction
- Modify the driver and AP to make the size of new raid (Raid0/1/10/JBOD) be the multiple of 128K. It avoid the complicated calculation in getting the actual access address when the raid size is in sector unit.
- Modify the algorithm of calculating data address to support the feature that RAID0 rebuilding can continue even after a surprised interrupt like shut down or hot plug.
- Modify Uninstall program to delete JMicron's OEMx.inf completely even the INF file is read-only. (Solve the issue of finding our driver after removing our driver in add/remove program window)
- Note
- Append a customized key "DisableRemoveRaid" in setup.ini to disable the RAID removing function. Default is 0 and indicate to "Enable" remove raid function.
eg. "DisableRemoveRaid"=1, indicate "Disable remove raid".
"DisableRemoveRaid"=0, indicate "Enable remove raid". (Default)
---------------------------------------------------------------------------------------------------------------------------------
R1.17.12.00 (02/01/07')
- Note
- Adding the feature that RAID0 rebuilding can continue even after a surprised interrupt like shut down or hot plug.
- Adding Foxconn subsystem vendor ID 0x0DF9105B, 0x0D09105B.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.11.02 (01/29/07')
- Note
- Adding JMB362 description in oemsetup.txt.
- Issue Correction
- PMP detection failed. PMP power on/off failed. PMP HDD hot-plug failed sometimes.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.11.01 (01/23/07')
- Note
- Modify Raid AP and installation for SiS package (R1.17.11.01s).
- Adding Foxconn subsystem vendor ID 0x0D18105B, 0x0CEA105B.
- Adding Vista support in txtsetup.oem.
- Issue Correction
- SATA HDD wakes up late.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.11.00 (01/19/07')
- Note
- This revision of driver can wake up from S3 in less than 2 seconds in Vista(measured by pwrtest) or WinXP(measured by bootvis).
(for all customers including Gigabyte)
---------------------------------------------------------------------------------------------------------------------------------
R1.17.10.05 (01/17/07')
- Issue Correction
- RAID1 disk was detected as non-RAID disk after hot plugging out then in.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.10.04 (01/16/07')
- Issue Correction
- Sony IDE DVD-RW DW-G120A failed to be detected.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.10.03 (01/15/07')
- Issue Correction
- Resuming from S3/S4 spends about 60 seconds more for 1.5G HDD.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.10.02 (01/15/07')
- Note
- Adding ECS subsystem vendor ID 0x6A001019, 0x11071734 and Clevo subsystem vendor ID 0x22001558, 0x09021558.
- Shorten the resuming time of S3/S4. The time should be the same as standard IDE driver for SATA devices. For
PATA devices, it needs about 4 seconds more than standard IDE driver.
- Issue Correction
- Hot plug failed.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.10.01 (01/11/07')
- Note
- Ignore the registry key "CustomizedSetting2" in driver.
- Issue Correction
- S3/S4 failed.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.10.00 (01/08/07')
- Note
- Adding the key "CustomizedSetting2" in registry to enable/disable SATA device detection when resuming from sleeping mode.
- Adding NCQ information.
- Remove the raid AP version in About dialog. And only show the first 3 major version of the driver version (eg. V1.17.08) and remove the internal version in about dialog
- Adding Quanta subsystem vendor ID 0xC1041631, 0xC1051631.
- Issue Correction
- Power off JMB336 and then power on, the system will hang for several seconds.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.09.01 (12/21/06')
- Note
- Adding Gigabyte subsystem vendor ID 0x3025103C.
- Issue Correction
- Maxtor DiamondMax Plus 9 HDD (80GB SATA/150) failed the CCtest.
(The most easily reproduced scenario is -
OS on JMB363 SATA HDD, another HDD is not connected in booting.
Then hot plugging the Maxtor SATA HDD, run CCtest D: -> D: copy.)
---------------------------------------------------------------------------------------------------------------------------------
R1.17.09.00 (12/19/06')
- Issue Correction
- Windows XP built-in CD-burning function failed.
- After rebuilding Raid1 or Raid10 on the disk that is previously reverted to nonRaid in OPROM, the OS on the disk could not properly boot up.
(Modify the last 2 byte of the disk MBR sector before rebuilding. Then the disk signature could be overwriten properly.)
---------------------------------------------------------------------------------------------------------------------------------
R1.17.08.02_noIDESetup (12/11/06')
- Note
- Modify setup program to remove the setup program for Standard IDE driver. The driver is R1.17.08.01 (with R1.17.08WHQL driver).
- The setup program will read the customized item "DisableIDESetup" in the setup.ini to determine whether providing IDE setup.
(If DisableIDESetup=1, indicate "NOT provide IDE setup". If DisableIDESetup=0 or not exist, indicate "provide IDE setup".)
---------------------------------------------------------------------------------------------------------------------------------
R1.17.08.02_360noRaidAP (12/11/06')
- Note
- Modify setup program to disable Raid AP and start menu item for JMB360. The driver is R1.17.08.01 (with R1.17.08WHQL driver).
- The setup program will read the customized item "DisableRaidAPForJMB360" in the setup.ini to determine whether installing Raid AP for JMB360.
(If DisableRaidAPForJMB360=1, indicate "NOT install Raid AP". If DisableRaidAPForJMB360=0 or not exist, indicate "Install Raid AP".)
---------------------------------------------------------------------------------------------------------------------------------
R1.17.08.01 (12/06/06')
- Note
- Foxconn subsystem vendor ID 0x0C72105B, 0x0C73105B, 0x0C75105B and 0x0D11105B were added in inf.
- Issue Correction
- While rebuilding OS Raid 0+1, system will crash.
- "Sleeper" shows the message that S4 resuming time is too long.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.08.00 (11/29/06')
- Note
- Foxconn subsystem vendor ID 0x0CE7105B and 0x300319DB were added in inf.
- Issue Correction
- The security status of Seagate SATA HDD ST3120827AS is still not frozen even if BIOS sets it to frozen status.
- ASUS testing tool - WINATA got wrong HDD model.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.07.06_noIDEsetup (11/28/06')
- Note
- Only modify setup program (based on 1.17.07.03). Driver is R1.17.07.06.
- Remove the setup program for Standard IDE driver.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.06.05_360noRaidAP (11/22/06')
- Note
- It's a special revision basing on R1.17.06.05 (with R1.17.06WHQL driver) to disable Raid AP and start menu item for JMB360.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.07.06 (11/22/06')
- Note
- ABIT subsystem vendor ID 0x1082147B was added in inf.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.07.05Disable_Ncq (11/21/06')
- Note
- It's a special revision basing on R1.17.07.05 to disable NCQ for two JMB330 enclosures.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.07.05 (11/21/06')
- Note
- Only driver changed. Setup and RAID ap are the same as R1.17.07.03.
- Changing the disk reporting sequence for Vista. After changing, the scenario should be as followings.
1. Install Vista with a mirror RAID of hard disk A and B.
2. Revert A to non-RAID disk in BIOS.
3. Booting with both A and B connected.
4. Booting with B alone will succeed.
5. Booting with A alone will fail.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.07.04 (11/16/06')
- Note
- Only modify setup program (based on 1.17.07.00). Driver is not changed.
- Remove the setup program for Standard IDE driver.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.07.03 (11/16/06')
- Note
- Only modify RAID AP and setup program . Driver is not changed.
- The setup program will overwrite all installed files and start menu items with the newly installed files and items.
(Eg, If the user has installed Gigabyte package first and now install JMicron Package, the setup program will overwrite all Gigabyte files and items with newly installed JMicron package.)
- Issue Correction
- In windows, Unplug one member disk of the Raid which is created by BIOS and Raid AP will show an error message and then close itself.
- When user unplug all HDDs or unplug a member disk of Raid0 which make the Raid damaged and OS detect no HDD on JMB36X controller, Raid AP will not refresh the UI content.
(Solution: Raid AP will show a warning message and close itself. In power saving mode, the Raid AP will turn off the device hotplug sensing.)
---------------------------------------------------------------------------------------------------------------------------------
R1.17.07.02 (11/15/06')
- Note
- Only modify RAID AP for Gigabyte. Driver is not changed.
- Issue Correction
- Modify the size of message sub-window in the "About" dialog to make the Raid AP version be shown in one line.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.07.01 (11/10/06')
- Issue Correction
- Creating RAID 1 with RAID AP, plug out one HDD of the RAID in Windows and then rebuilding the RAID in BIOS.
The RAID AP still shows the RAID is not synched.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.07.00 (11/08/06')
- Note
- Modify Raid AP and installation program to show correct driver package version (Read the "DriverVer" item written in INF file).
- Customize the strings, window title and bitmaps for Gigabyte. (R1.17.06.06g)
- Issue Correction
- Only one HDD of PMP was detected.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.06.05 (11/06/06')
- Note
- Only installation program changed. Driver and RAID ap didn't change.
- Issue Correction
- Fix the issues of installing driver when OS is located at PATA disk in vista 32/64Bit.
- Fix the issues of uninstall driver in Vista 64bit and WinXP/2003Server 64Bit.
- Setup program installed driver for JMB368.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.06.04express (11/02/06')
- Note
- Driver : jmb36x.sys is not changed. Only jgogo.sys changed.
- Issue Correction
- Express card with HDD connected still exists in device manager if removing it in S3.
- Fix the issues of installing IDE driver when install multi-function mode under win2000/winXP/win2003 Server 32Bit.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.06.04 (11/02/06')
- Note
- Adding JMB369 device ID in jmide.inf.
- MSI subsystem vendor ID 0x72381462 was added in inf.
- Driver is not changed.
- Issue Correction
- Fix the issues of installing IDE driver when install multi-function mode under win2000/winXP/win2003 Server 32Bit
---------------------------------------------------------------------------------------------------------------------------------
R1.17.06.03 (10/30/06')
- Note:
- Provide IDE setup program that is embeded in our current JMB36X setup program.
(When setup program detect single IDE controller, it will show a wizard dialog for user to select IDE driver or JMicron SCSI driver. In other cases (NOT single IDE controller), the wizard dialog will not appear. In silent install mode, the default is to install JMicron driver for single IDE controller.)
- After installing JMicron SCSI WHQL driver under single mode, users change to Multi-function mode. A program will automatically be launched to detect if multi-IDE mode is installed with JMicron SCSI driver. If yes, it will call another program to install standard IDE driver.
- Issue Correction
- SATA detection failed sometimes.
- Solve the problem of showing the unsigned driver dialog when install JMicron WHQL driver under multi-function mode 0101/0104 and 0101/0106 in windows Vista 32/64 bit OS. Also modify uninstallation program.
(Use another method to install JMicron driver on all JM controllers and update IDE driver for IDE controller again.)
- (Raid AP bug) The driver version shown in About dialog is empty in WinXP/2003 Server 64 bit OS.
- (Raid AP bug) Show the controller logo bitmap in select controller dialog.
- (Raid AP bug) Show the warning message when user manually execute Raid AP under single IDE mode or multi-0101/0106 AHCI mode.
- When installing standard IDE driver, don't remove the files under " windows\JM" because those files might be used in uninstalling JMicron SCSI driver that is previously installed.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.06.02 (10/25/06')
- Issue Correction
- JM20336 enclosure failed to be detected.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.06.01 (10/20/06')
- Note
- Only installation AP changed. Driver & RAID AP are the same as R1.17.05.01.
- W/R the issue that single IDE change to multi-function and update MS standard IDE driver on JMicron 0101 function.
- Add a dialog box for user to select to replace MS MS standard IDE driver with our JMicron driver when detecting single IDE.
(Silent mode will not show this dialog, always install JMicron driver)
---------------------------------------------------------------------------------------------------------------------------------
R1.17.06.00 (10/19/06')
- Note
- Only installation AP changed. Driver & RAID AP are the same as R1.17.05.01.
- Update installation and show a dialog box for user to decide if installing JMicron driver or not when detecting single IDE controller.
- Run an application to detect multi-function when system restarting and update the IDE function with MS standard IDE driver if neccessary.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.05a (10/18/06')
- Note
- Update installation and show a dialog box for user to decide if installing JMicron driver or not when detecting single IDE controller.
- Run an application to detect multi-function when system restarting and update the IDE function with MS standard IDE driver if neccessary.
- Based on R1.17.05 driver
---------------------------------------------------------------------------------------------------------------------------------
R1.17.03aWHQL (10/18/06')
- Note
- Update installation and show a dialog box for user to decide if installing JMicron driver or not when detecting single IDE controller.
- Run an application to detect multi-function when system restarting and update the IDE function with MS standard IDE driver if neccessary.
- Based on R1.17.03WHQL driver
---------------------------------------------------------------------------------------------------------------------------------
R1.17.05.01 (10/16/06')
- Issue Correction
- It needs more than 2 minutes to resume from hibernation on some platforms.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.05.00 (10/12/06')
- Issue Correction
- A RAID including 2 IDE HDDs failed in formating.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.04.00 (10/10/06')
- Note
- MSI subsystem vendor ID 0x72351462 was added in inf.
- Issue Correction
- Failed to burn DVD-RW format. (DVD+RW and CD-R are OK.)
---------------------------------------------------------------------------------------------------------------------------------
R1.17.03.02 (10/05/06')
- Issue Correction
- When installing OS in RAID 1, the system hangs after reading floppy.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.03.01 (10/04/06')
- Issue Correction
- IDE ODD disappears.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.03.00 (10/02/06')
- Note
- ASUS subsystem vendor ID 0x824F1043 was added in inf.
- Issue Correction
- CCTest (Gigabyte test tool) hangs with JMicron RAID on 4-core CPU platform.
- A space character intervenes in the HDD model name.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.02.01 (09/26/06')
- Issue Correction
- SCSI compliance test of DTM failed.
- Fail to install driver on Vista x64 platform.
- The file version in the version page of driver file properties is not correct.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.02.00 (09/24/06')
- Issue Correction
- SCSI compliance test of DTM failed.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.00.04 (09/17/06')
- Issue Correction
- JM20336 enclosure HDD power is on/off several times when enclosure power button is turned on.
- ATAPI device (CDROM/DVDROM) doesn't show in "Safely Remove Hardware" list.
- JBOD with PATA member failed to resume from S3.
- PATA performace drops drastically after resuming from S3.
- Note
- Add Foxconn subsystem vendor ID 0x0D08105B.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.00.03 (09/14/06')
- Issue Correction
- S3 failed with Hitachi IC35L180AVV207-1 185.2GB PATA HDD.
- Creating RAID from existing disk and RAID rebuilding using Seagate SATA HDD as source are easy to fail when block size is 128 KB.
- Creating RAID from existing disk and RAID rebuilding are easy to fail at start.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.00.02 (09/06/06')
- Issue Correction
- Driver shows not signed by WHQL.
- Full format failed with PATA RAID.
---------------------------------------------------------------------------------------------------------------------------------
R1.16.02WHQL (09/06/06')
- Note
- Only setup AP changed. Driver is the same as R1.16.01.
- Issue Correction
- Driver shows not signed by WHQL.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.00.01 (09/01/06')
- Issue Correction
- The "open/close disc" button of WinDVD doesn't work.
- New UI
- New Feature:
1. Show "driver version" and "Raid AP version" in About dialog
2. Popup a dialog for user to decide whether doing resynching or not when detecting the raid which need resynching.
- Bugs fixed:
1.Remove RAID Wizard, select item error. (RAID0 and JBOD cause crash)
2.The Raid AP will not shown on the top most already.
3. Enter key in all dialogs isn't correct. (will not close the dialog)
4. Downgrade Driver and AP. AP UI is still new.
5.Remove RAID item of toolbar, when select one of raid, Disk Members post will miss one HDD.
6.When HDD name is long, it can't show full HDD information in Disk Members in RAID information.
7.Conflict warning message box isn't shown properly.
8.."Create new RAID" and "Create RAID from Exsiting HDD" messagebox, ¦b"RAID name"¨º¤@Äæ¡A§Æ±æ¯àÅý´å¼Ðª½±µ¦b¸ÓÄæ§@¥Î, ¦Ó¤£»Ýn¦A¥Î·Æ¹«ÂI¨ú.
9. Combo box in wizard dialog will not be colored with blue at early state.
---------------------------------------------------------------------------------------------------------------------------------
R1.15.02aWHQL (08/30/06')
- Note
- It's a special revision for ASUS notebook.
- Not install RAID AP for JMB360.
- Only AP changed. Driver is the same as R1.15.01.
---------------------------------------------------------------------------------------------------------------------------------
R1.15.02WHQL (08/30/06')
- Note
- Only setup AP changed. Driver is the same as R1.15.01.
- Issue Correction
- Driver shows not signed by WHQL.
---------------------------------------------------------------------------------------------------------------------------------
R1.17.00.00 (08/25/06')
- Note
- New UI of RAID AP.
- Driver is the same as R1.16.01.
---------------------------------------------------------------------------------------------------------------------------------
R1.16.01 (08/23/06')
- Issue Correction
- Formatting RAID failed in some cases.
- Note
- Adding ECS subsystem/vendor ID E0291631/E02A1631.
---------------------------------------------------------------------------------------------------------------------------------
R1.16.00 (08/18/06')
- Note
- Adding silent install.
- Set RAID 0 default block size as 64K.
- Reduce the CPU utilization and improve the performance.
---------------------------------------------------------------------------------------------------------------------------------
R1.12.08 (08/10/06')
- Note
- Porting from R1.14.01 to w/r the issue : when switching to multi-function, IDE will load JMB36x driver instead of
default IDE driver.
- Adding silent install.
- Only AP changed. Driver is the same as R1.12.07.
---------------------------------------------------------------------------------------------------------------------------------
R1.15.01 (08/10/06')
- Issue Correction
- The burst performance of HdTach of 3G HDD exceeds 2.5G.
---------------------------------------------------------------------------------------------------------------------------------
R1.15.00 (08/09/06')
- Issue Correction
- The resuming time of S1/S3 is too long. (Penalty is IDE device can't be plugged in/out in sleeping mode.)
- The HdTach burst performance of SATA 1.5G HDD is not reasonable after hot plug.
- Note
- Porting from R1.12.07 : To w/r ASUS DVD ROM issue (DVD ROM disappears in the process of copying data).
- Driver passes HDD capability(1.5G/3G) instead of channel speed to AP. So AP shows the HDD capability, not the channel speed.
---------------------------------------------------------------------------------------------------------------------------------
R1.12.07 (08/04/06')
- Note
- To w/r ASUS DVD ROM issue (DVD ROM disappears in the process of copying data).
---------------------------------------------------------------------------------------------------------------------------------
R1.14.01 (07/31/06')
- Issue Correction
- The PMP HDD will be lost after resuming from S3.
- HDTach burst performance is over SATA & PCIE limitation.
- Windows Vista failed to install on JMB36x HDD with JMB36x driver.
- When switching to multi-function, IDE will load JMB36x driver instead of default IDE driver.
- Note
- Removing JMB362 chip ID since it's the same as JMB363.
- Renaming inf files for "Windows Update" issue.
- Adding ASUS subsystem/vendor ID 82021043.
---------------------------------------------------------------------------------------------------------------------------------
R1.12.06 (07/30/06')
- Note
- Porting from R1.13.06 to w/r the issue that IDE HDD will be lost when resuming from S3 in 64-bit OS.
---------------------------------------------------------------------------------------------------------------------------------
R1.14.00c (07/25/06')
- Note
- W/r express card hot-plug issue of chip rev.2. (like R1.08.00c)
- Only setup program changed and adding a w/r AP, driver and RAID AP are the same as R1.14.00.
---------------------------------------------------------------------------------------------------------------------------------
R1.14.00 (07/24/06')
- Request
- Adding one special case for JMB360 to support PMP RAID.
- Set RAID structure subversion to 1 when set RAID sync.
- Adding JMB362 chip ID in miniport driver.
- Adding ASUS subsystem/vendor ID 824C1043.
---------------------------------------------------------------------------------------------------------------------------------
R1.13.07 (07/20/06')
- Request
- To w/r h/w issue that sometimes SATA connection failed after S3/hot plug/power off.
---------------------------------------------------------------------------------------------------------------------------------
R1.13.06 (07/18/06')
- Issue Correction
- IDE HDD will be lost when resuming from S3 in 64-bit OS.
---------------------------------------------------------------------------------------------------------------------------------
R1.12.05 (07/14/06')
- Issue Correction
- Porting from R1.13.03 the new way to w/r the issue that the system failed to resume from S3 when OS is in IDE HDD.
---------------------------------------------------------------------------------------------------------------------------------
R1.13.05 (07/12/06')
- Note
- Only AP changed. Driver is the same as R1.13.04.
- Issue Correction
- When resuming from sleeping mode, RAID AP will show error message.
---------------------------------------------------------------------------------------------------------------------------------
R1.13.04 (07/11/06')
- Request
- AP show disk capacity to 4 decimal digits.
- Issue Correction
- When creating SATA/IDE/PMP mixed RAID 1/0+1, the RAID will always be set as degraded(not synchronized) by BIOS.
(That's because BIOS doesn't recognize PMP disk 1-4 so it will always mark the RAID as member-lost.)
- AP show error message in AHCI mode.
---------------------------------------------------------------------------------------------------------------------------------
R1.13.03 (07/07/06')
- Note
- New way to w/r the issue that the system failed to resume from S3 when OS is in IDE HDD.
(This is a side effect since R1.11.00 - Issue Correction - If changing the HDD channel when system is sleeping,
the HDD fails to be detected when system wakes up.)
- Enable RAID AP for JMB360.
- Change "JMicron RAID" string into "JMB36x RAID" to avoid the patent issue.
---------------------------------------------------------------------------------------------------------------------------------
R1.12.04 (07/05/06')
- Issue Correction
- W/r the issue that the system failed to resume from S3 when OS is in IDE HDD (Win2000 in WD HDD).
---------------------------------------------------------------------------------------------------------------------------------
R1.13.02 (07/04/06')
- Request
- Show warning message when hot plug happens.
- Issue Correction
- Hot plug makes system crash when OS is accessing the disk.
---------------------------------------------------------------------------------------------------------------------------------
R1.13.01 (06/30/06')
- Note
- Porting following items from R1.11.02.
- [ASUS] In multi-AHCI mode and OS is in JMB36x PATA HDD, uninstalling driver makes the system unbootable.
- Porting following items from R1.12.03.
- Eanbling RAID function in single AHCI mode for JMB36x add-on card.
- W/r the issue that the system failed to resume from S3 when OS is in IDE HDD.
- To be able to mix PATA, SATA & PMP HDDs to build a RAID.
- Issue Correction
- Hibernation failed.
- Hot plug makes system crash in some cases.
- AP can run in single IDE mode.
- The "add or remove programs" window of WinXP-64 can't be closed after removing JMRAID AP.
---------------------------------------------------------------------------------------------------------------------------------
R1.12.03 (06/26/06')
- Request
- Eanbling RAID function in single AHCI mode for JMB36x add-on card.
- Issue Correction
- W/r the issue that the system failed to resume from S3 when OS is in IDE HDD.
---------------------------------------------------------------------------------------------------------------------------------
R1.11.02 (06/23/06')
- Note
- Basing on R1.11.01.
- Only setup changed.
- Issue Correction
- [ASUS] In multi-AHCI mode and OS is in JMB36x PATA HDD, uninstalling driver makes the system unbootable.
---------------------------------------------------------------------------------------------------------------------------------
R1.13.00 (06/23/06')
- Note
- Supporting Port-Multiplier RAID. When PMP is connected, AP shows PMP HDDs only.
- RAID driver architecture changed.
- To show warning message if user wants to close RAID AP when RAID rebuilding is processing.
- Request
- [ASROCK] Minimizing RAID AP to system tray when clicking the close button.
- [GBT] Providing a dll for GBT to develop their UI.
---------------------------------------------------------------------------------------------------------------------------------
R1.12.02 (06/22/06')
- Request
- Driver doesn't change class code for JMB360.
---------------------------------------------------------------------------------------------------------------------------------
R1.12.01 (06/16/06')
- Request
- [ASROCK] Adding subsystem vendor ID 23631849.
---------------------------------------------------------------------------------------------------------------------------------
R1.12.00 (06/15/06')
- Request
- Adding SCSIOP_IDE_PASS_THROUGH operation code for JMB33x AP.
- Issue Correction
- [GBT] Failed to recognize the RAID created by BIOS with Maxtor HDD DiamondMax 10 (Model:6L080M0).
(This type of HDD supports LBA28 & NCQ, but NCQ only supports LBA48. So don't use NCQ command with this type of HDD.)
- Failed to access Sunplus enclosure.
---------------------------------------------------------------------------------------------------------------------------------
R1.11.01 (06/13/06')
- Issue Correction
- If changing the HDD channel when system is sleeping, the HDD fails to be detected when system wakes up.
(when OS is installed in JMB36x HDD)
---------------------------------------------------------------------------------------------------------------------------------
R1.11.00 (06/12/06')
- Issue Correction
- If changing the HDD channel when system is sleeping, the HDD fails to be detected when system wakes up.
- Failed to detect NEC SATA DVD+/-RW NEC ND-3650A.
---------------------------------------------------------------------------------------------------------------------------------
R1.10.05 (06/07/06')
- Issue Correction
- In multi-function mode, Win2000 3 in 1 CD failed to install when ODD is connected to JMB36x PATA slot.
---------------------------------------------------------------------------------------------------------------------------------
R1.10.04 (06/07/06')
- Note
- Basing on R1.10.03a but not to install driver for mulit-function IDE.
- Issue Correction
- Win2000 3 in 1 CD failed to install.
---------------------------------------------------------------------------------------------------------------------------------
R1.09.04a WHQL (06/05/06')
- Note
- Basing on R1.09.04 WHQL.
- Only setup changed.
- Fix bug: remove "JMicron Technology Corp" menu item from the Start Program Menu for JMB360.
---------------------------------------------------------------------------------------------------------------------------------
R1.10.03a (06/03/06')
- Note
- It's for ASUS P5B-Delux only.
- Be able to install JMB36X driver for any mode (single/multi) and any device (IDE/AHCI/RAID).
- Driver, inf and txtsetup.oem are changed. Setup & RAID AP are not changed this time and will be released when necessary.
So if a exclamation mark on IDE device was found after running setup, please update JMicron driver for IDE device.
- SATA & IDE HDD can be used as RAID seperately.
---------------------------------------------------------------------------------------------------------------------------------
R1.10.02 / R1.10.02g (06/02/06')
- Request
- GBT
- Show "GBB36X Controller" instead of "GBB36X RAID Controller".
- Adding default subsystem vendor ID.
- Issue Correction
- System crashed after installing driver for JMB361/363 express card on IBM notebook.
- System crashed when installing driver if PATA ODD was connected.
- The broken RAID shows synchronized even if the rebuilding process was interrupted.
---------------------------------------------------------------------------------------------------------------------------------
R1.08.01c (05/29/06')
- Basing on R1.08.00c.
- Correcting the issue that system crashed after installing driver for JMB361/363 express card on IBM notebook.
---------------------------------------------------------------------------------------------------------------------------------
R1.10.01 / R1.10.01g (05/29/06')
- Issue Correction
- System crashed after installing driver for JMB360 add-on card.
---------------------------------------------------------------------------------------------------------------------------------
R1.10.00 / R1.10.00g (05/24/06')
- Request
- Adding single/multi function rules.
- Issue Correction
- GBT
- If OS is installed in the 2nd JMB36X HDD, hibernation will go into blue screen.
---------------------------------------------------------------------------------------------------------------------------------
R1.09.05 / R1.09.05g (05/22/06')
- Issue Correction
- Only modified inf files & txtsetup.oem.
---------------------------------------------------------------------------------------------------------------------------------
R1.09.04 / R1.09.04g (05/19/06')
- Issue Correction
- "HCT : Driver Verifier Test" failed.
---------------------------------------------------------------------------------------------------------------------------------
R1.09.03 / R1.09.03g (05/17/06')
- Changing JMB36X into GBB363 in oemsetup.txt, inf file and setup program.
---------------------------------------------------------------------------------------------------------------------------------
R1.09.02g (05/16/06')
- Merging jraid.inf and jahci.inf and using different oemsetup.txt for single/multi function.
---------------------------------------------------------------------------------------------------------------------------------
R1.09.01 / R1.09.01g (05/12/06')
- Note
- Only modified the setup program for Chinese version of OS. Driver & RAID AP didn't change.
---------------------------------------------------------------------------------------------------------------------------------
R1.09.00g (05/12/06')
- Request
- GBT
- AP uses GBT logo.
- Note
- Driver is the same as R1.09.00
---------------------------------------------------------------------------------------------------------------------------------
R1.09.00 (05/12/06')
- Request
- GBT
- Support multi-function.
- Others
- Driver doesn't change class code.
- Bug Fixed
- ASUS
- Rebuilding RAID 1 from channel 1 to channel 0 failed.
- Some error messages appear when removing driver on Windows server 2003 R2.
- GBT
- The system shuts down slowly when PMP HDD connected.
- Others
- Installing JMB360 twice in different PCIE slots crashes the system.
(Enable/disable driver makes driver fail to install.)
---------------------------------------------------------------------------------------------------------------------------------
R1.08.00c (04/27/06')
- w/r express card hot-plug issue of chip rev.2.
- Only setup program changed and adding a w/r AP, driver and RAID AP are the same as R1.08.00.
---------------------------------------------------------------------------------------------------------------------------------
R1.08.00 (04/27/06')
- Request
- ASUS
- Disable PATA RAID by system BIOS.
- GBT
- Adding GBT subsystem vendor ID B0001458/B0011458/B0021458/B0031458.
---------------------------------------------------------------------------------------------------------------------------------
R1.07.01 (04/20/06')
- Request
- ASUS
- Show 1.5G/3G infomation on the RAID AP.
---------------------------------------------------------------------------------------------------------------------------------
R1.07.00 (04/19/06')
- ASUS Issues
- OS installed in ICH8 disk failed to boot after removing JMB36x software.
- More than one PMP disk displays in subwindow of AP.
- Adding ASUS subsystem vendor ID 13481043.
- Other Issues
- SATA CDROM LTN-48S1S failed to be detected.
---------------------------------------------------------------------------------------------------------------------------------
R1.06.02 (04/06/06')
- Note
- Driver is the same as R1.06.01. Only AP changed.
- ASUS Issues
- The RAID still shows not synched after resynching.
---------------------------------------------------------------------------------------------------------------------------------
R1.06.01 (04/03/06')
- Other Issues
- "HCT driver verifier test" failed in 64-bit OS.
- "HDTech burst read" is low in first-time test after booting up.
---------------------------------------------------------------------------------------------------------------------------------
R1.06.00 (03/30/06')
- Gigabyte Issues
- IDE performance is bad with HDTach average write test (only single master drive has the issue).
- Other Issues
- Not to install RAID AP in JMB360.
---------------------------------------------------------------------------------------------------------------------------------
R1.05.06 (03/24/06')
- MSI Issues
- To be able to remove AP even if there is no JMB36x controller.
- When booting up, there should be no AP icon in system tray if there is no JMB36x controller.
- Foxconn Issues
- FUJITSU MHT2080BH 80G HDD access failed.
- Seagate ST830011AS HDD has NCQ issue, so disable NCQ when the HDD connected.
- Other Issues
- HD Tach burst performance swings.
- The installing process stalls for a while sometimes.
- In rebuilding RAID, the text on the left side of the progress bar disappears sometimes.
---------------------------------------------------------------------------------------------------------------------------------
R1.05.05 (03/15/06')
- Fix bug : partition size is wrong after removing RAID.
- Fix bug : partition can't be accessed after removing RAID 0/0+1.
- New Feature : If there is no JMB36x card attached, AP doesn't show any warning message when booting but only show
when user executes it.
- W/r the long trace issue.
---------------------------------------------------------------------------------------------------------------------------------
R1.05.03 (03/09/06')
- Only added ASUS subsystem ID.
---------------------------------------------------------------------------------------------------------------------------------
R1.05.02 (03/08/06')
- Creating RAID from existing disk for RAID 0/0+1/JBOD.
- RAID rebuilding for RAID 0+1.
- Increase the rebuild buffer to 128K to greatly shorten the rebuild time.
- Fix the bug that failing to rebuild if the RAID slot index of the source disk is not 0.
- To fix the S3 issue of Foxconn.
- To fix the issue that syscache test failed.
- To solve special sequence issue on RAID 1 plug.
- To disable rebuilding option when there is only one disk.
- To fix the bug - After hot plugging, RAID becomes normal without resynching.
---------------------------------------------------------------------------------------------------------------------------------
R1.05.01 (03/02/06')
- Fix the issue of failing to sleep in S3 on Foxconn platform.
---------------------------------------------------------------------------------------------------------------------------------
R1.05.00 (03/01/06')
- Improve the burst read performance of HD Tach.
- It's for SATA HDD, not for IDE.
- It's for single HDD/RAID0/RAID1/JBOD, not for RAID0+1 (since need IDE in RAID0+1)
- W/r the h/w long trace issue.
- Removing the pseudo device, thus there is no 2nd installation needed.
---------------------------------------------------------------------------------------------------------------------------------
R1.04.05 (02/20/06')
- Only modify txtsetup.oem.
---------------------------------------------------------------------------------------------------------------------------------
R1.04.04 (02/15/06')
- Clear HDD when creating RAID.
- Show error message when reomving RAID.
---------------------------------------------------------------------------------------------------------------------------------
R1.04.00 (02/06/06')
- Solve ASUS issue : to be able to create RAID with the booting system HDD.
- Solve ASUS issue : change the default "Yes" to "No" of the pop-up warning dialogue box of removing RAID.
- Solve ASUS issue : except the progress bar, also show message of the executing action (rebuilding/resynching).
- Solve ASUS issue : show message that the data will be reserved when creating RAID from existing HDD.
- Solve ASUS issue : show message that the data will be cleared when creating RAID.
- Solve ASUS issue : change the string "eSATA" to "SATA".
- SOlve ASUS issue : change the word "recover" to "rebuild".
---------------------------------------------------------------------------------------------------------------------------------
R1.03.00c1 (01/25/06')
- W/R JMB360 chip revision A issue (PCI 0x4C-0x4F = 0)
---------------------------------------------------------------------------------------------------------------------------------
R1.03.02 (01/23/06')
- Only AP fixed some bugs. Driver is the same as R1.03.00 & R1.03.01.
---------------------------------------------------------------------------------------------------------------------------------
R1.03.01 (01/19/06')
- Basing on R1.03.00.
- Add RAID1 auto-resynching, RAID 1 recovery, creating RAID 1 from existing HDDs.
---------------------------------------------------------------------------------------------------------------------------------
R1.03.00c (01/19/06')
- W/R JMB360 chip revision A issue
---------------------------------------------------------------------------------------------------------------------------------
R1.03.00 (01/18/06')
- Foxconn
- Can remove only the eSATA HDD
- Others
- Add JMB360 supporting in the driver
- Add upper filter driver
- Hot plug issue of single CDROM
- IDE performance - burst 118.3 MB/s, average 48.7 MB/s
---------------------------------------------------------------------------------------------------------------------------------
R1.02.00 (01/04/06')
- Solved the IDE performance down issue. The performance is about 86.8 MB/s measured with HD Tach after the bug fixed.
- Disable "create RAID" function when there is only one HDD connected. Disable RAID 0+1 option when the connected HDDs is less than 4.
- Solved ASUS K8V-XE issues
10. In AP, drop RAID 0+1 option only for ASUS K8V-XE
14. HDD can not be identified on specific SATA Port of Port Multiplier (PM) that is 1-to-5 port
---------------------------------------------------------------------------------------------------------------------------------
R1.01.00 (12/22/05')
- Solved the hot-plug issue.
---------------------------------------------------------------------------------------------------------------------------------
R1.00.00 (12/06/05')
- RAID rebuild : finished, about 100G bytes per hour.
- Reduce the global data area (device extension) size.
---------------------------------------------------------------------------------------------------------------------------------
R0.94.01 (11/28/05')
- Disable MSI cap.
---------------------------------------------------------------------------------------------------------------------------------
R0.94.00 (11/28/05')
- Fix the S4 issue.
- Port multiplier verified.
---------------------------------------------------------------------------------------------------------------------------------
R0.92.02 (11/22/05')
- This revision should be able to pass HCT in both 32-bit and 64-bit OS.
- Suspend & hibernation are OK.
- Set the PMP limit to 8.
- Fix the bug - long time to wait for loading driver while pre-install OS with JBOD mode.
- Fix the bug - failed to recognize RAID correctly as non-RAID HDDs inserting among RAID-HDDs.
---------------------------------------------------------------------------------------------------------------------------------
R0.92.01 (11/17/05')
- Fix bug - failed to recognize RAID created by BIOS.
---------------------------------------------------------------------------------------------------------------------------------
R0.92.00 (11/16/05')
- Known bug (not fixed) - fail to resume from hibernation.
- Not supported - RAID rebuilding.
---------------------------------------------------------------------------------------------------------------------------------
R0.91.01 (11/03/05')
- Fix bug - WinXP can't install on some platforms with some RAID configurations.
- JMRaidTool
- Support multi-adapter
- Fix bug - hot plug fails sometimes.
- Fix bug - Don't let user select block size in mirror & JBOD configurations.
- Clear partition table when deleting RAID to prevent old partition info from displaying in OS disk manager.
- Automatically show current disk or RAID info after deleting RAID so user doesn't need to push the get-info button.
---------------------------------------------------------------------------------------------------------------------------------
R0.91.00 (10/31/05')
- Support RAID 0, 1, 0+1, JBOD.
- Support WinXP/Win2003/Win2000.
- Support WinXP x64/Win2003 x64 (can only install by inf, not by setup.exe).
- Support ATAPI device.
- Support port multiplier.
- Support hot plug.
- Support boot & install OS on RAID.
---------------------------------------------------------------------------------------------------------------------------------
R0.90.02e (10/27/05')
- Basing on r0.90.01e.
- Fix bug - RAID configuration tool doesn't work in r0.90.01e.
- Some CDROM can't be found.
---------------------------------------------------------------------------------------------------------------------------------
R0.90.01e (10/27/05')
- This revision doesn't support port multiplier, but can install WinXP on RAID.
---------------------------------------------------------------------------------------------------------------------------------
R0.90.01 (10/26/05')
- Support WinXP x64/Win2003 x64 (can only install by inf, not by setup.exe).
- JMRaidTool.exe calls static MFC library instead of dynamic library and
is compressed into package instead of locating in a seperate directory.
- Fix bug - code optimization causes some side effects.
---------------------------------------------------------------------------------------------------------------------------------
R0.90.00 (10/24/05')
- Support WinXP/Win2003/Win2000.
- Support RAID 0, 1, 0+1, JBOD.
- Support hot plug.
- Support boot & install OS on RAID.
- Support ATAPI device.
- Support port multiplier.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.