1. latest_eg.zip Driver
2. setip.txt File Contents

setip.txt Driver File Contents (latest_eg.zip)

Copyright March 2002 by ICP DAS CO., LTD. All right reserved.

Trademark:
  Products, names and trade names appeared belongs to their respective owner. 

This document describe the way to set the IP address, address mask,  
and gateway address of the I-7188EG controller.


******************************************************************
I-7188EG USES TCP/IP PORT NO. 502 TO TALK TO THE HMI 
AND ISAGRAF WORKBENCH.
******************************************************************


1. Create a file folder named "7188EG" in your hard drive. 
   For example, "c:\7188EG".

2. Copy \Napdos\ISaGRAF\7188EG\Driver\7188xw.exe, 7188xw.ini
   from the CD_ROM into your "7188EG" folder.

3. Run "\7188EG\7188x.exe" in your hard drive. A "7188xw" screen 
   will appear. 

4. Link from COM1 or COM2 of your PC to COM1 of the I-7188EG 
   controller by a RS232 cable. 

5. Power off the I-7188EG controller, connect pin "INIT*" to 
   "GND", and then power it up.

6. If the connection is Ok, messages will appear on the 7188xw screen.

      ICP_DAS MiniOS7 for I-7188E Ver. 2.00 build 001,May 16 2003 13:32:53
      SRAM:512K, FLASH MEMORY:512K
      [CPU=Am188ES]
      Serial number= 5A 5A 5A 5A 5A 5A 5A 5A

      i-7188E>

7. Type "ip" to see the current IP address of the I-7188EG .

      i-7188E> ip
      IP=192.168.255.1
      i7188e>

8. Type "setip xxx.xxx.xxx.xxx" to set to a new IP address.

      i-7188E> setip 192.168.1.200
      Set IP=192.168.1.200
      [ReadBack]IP=192.168.1.200
      i-7188E>

9. Type "mask" to see the current address mask of the I-7188EG .

      i-7188E> mask
      MASK=255.255.0.0
      i-7188E>

10.Type "setmask xxx.xxx.xxx.xxx" to set to a new address mask.

      i-7188E> setmask 255.255.255.0
      Set MASK=255.255.255.0
      [ReadBack]MASK=255.255.255.0
      i-7188E>

11.Type "gateway" to see the current gateway address.

      i-7188E> gateway
      Gateway=192.168.0.1
      i-7188E>

12.Type "setgateway xxx.xxx.xxx.xxx" to set to a new gateway address.

      i-7188E> setgateway 192.168.1.1
      Set GATEWAY=192.168.1.1
      [ReadBack]Gateway=192.168.1.1
      i-7188E>
13.Type "mac" to see the current Ethernet address.

      i-7188E> mac
      Ethernet Address=00:80:32:00:33:5e
      i-7188E>

14.Type "mac xx:xx:xx:xx:xx:xx" to set to a new Ethernet  address.

      i-7188E> mac 80:80:80:80:80:80
      Set Ethernet Address=80:80:80:80:80:80
      [ReadBack]Ethernet Address=80:80:80:80:80:80
      i-7188E>

15.Press ALT_X to exit "7188xw" and close the DOS SHELL, or 
   COM1/COM2 of the PC will be occupied. 

16. Remove the connection between "INIT*" - "GND", reset the 
    I-7188EG controller.