Copyright March 2002 by ICP DAS CO., LTD. All right reserved. The ISaGRAF embedded driver is firmware burned into the flash memory of the I-7188XG/I-7188EG. It can be easily upgraded by the user. Our newly released driver can also be obtained from the following website. ftp.icpdas.com/pub/cd/8000cd/napdos/isagraf/7188eg/driver/ Warning: The copyright of the firmware and ISaGRAF embedded driver belongs to ICP DAS CO., LTD. Only the I-7188XG/I-7188EG and I-8xx7 controller have registered a legal ISaGRAF Target license. To burn an ISaGRAF embedded driver into others is absolutely illegal and may be punished by law. Trademark: Products, names and trade names appeared belongs to their respective owner. Make sure of your current driver version before you upgrade it. Note: *******Only the legal I-7188EG/XG can get a legal license****** The 7188EG/XG has embedded ¡§license checking¡¨ since their driver version of 2.01. The 7188EG/XG delivered from ICP DAS after the date of Dec.01,2004 is burned with a legal license. That means they are already licensed. If your 7188EG/XG is embedded with old version (driver version 1.xx) & wish to update it to version of 2.01 or later. Please contact service@icpdas.com to get a legal license. Please writedown the 8-bytes serial No. & product serial No of your I-7188EG/XG as below, for example. 8-byte Serial No : 01 98 E1 A7 08 00 00 30 Product serial No. : I7188EG003KA003 (listed on the shell of your 7188EG/XG) ************** We use driver version 304 as an example ******************** 1. Create a file folder named "7188EG" in your hard drive. For example, "c:\7188EG". 2. Copy \Napdos\ISaGRAF\7188EG\Driver\3.13\"7188xw.exe", "7188xw.ini" , "7188xw.f4" , "isa7188e.exe" , "autoexec.bat" & "e-060915.IMG" from the CD_ROM into your "7188EG" folder. 3. Run "\7188EG\7188xw.exe" in your hard drive. A "7188xw" screen will appear. 4. Link COM1 or COM2 of your PC to COM1 of the I-7188EG controller through a RS232 cable. 5. Power off the I-7188EG controller, connect pin "INIT" to "GND" and then power it up. 6. If the connection is Ok, messages will appear on the 7188xw screen. ICP_DAS MiniOS7 for I-7188E Ver. 2.00 build 001,Jun 08 2006 13:32:53 SRAM:512K, FLASH MEMORY:512K [CPU=Am188ES] Serial number= 5A 5A 5A 5A 5A 5A 5A 5A i-7188E> 7. Type ver to see the current OS date and version i-7188E> ver ICP_DAS MiniOS7 for I-7188E Ver. 2.00 build 001,Jun 08 2006 13:32:53 SRAM:512K, FLASH MEMORY:512K [CPU=Am188ES] Serial number= 5A 5A 5A 5A 5A 5A 5A 5A 8. Type "isa7188e *p=", the driver version No. and copyright message will be displayed. i-7188E> isa7188e *p= Driver: I-7188EG : isa7188e.exe - V3.13, Oct.29,2010 MiniOS7: Must use e-060915.img Licence is OK NED-ID : 1 COM1 is Modbus RTU slave port,19200,8,N,1 (or COM1 is free) Use 'isa7188e *f=1' to free COM1, 'isa *f=0' to set COM1 as Modbus RTU Use 'isa7188e *s=1 to 255' to set NET-ID to 1 to 255 Use 'isa7188e *d=' to delete ISaGRAF program Use 'isa7188e *b=0 to 9' to set baudrate of COM1 as 1200,2400... Use 'isa7188e *x=PB' to set COM2/COM3 as Modbus RTU slave port P means port number, P: 2 or 3. B means baudrate, B:0 ~ 9 ex : isa7188e *x=24, set COM2 as Modbus RTU slave and baudrate is 19200 'isa7188e *x=f' to free COM2/COM3 port Baudrate are as follows : 1=2400,2=4800,3=9600,4=19200(default),5=38400,6=57600,7=115200,8=300,9=600,0=1200 (C)Copyright:ICP DAS CO. , LTD. Taiwan Id:84517297 9. Type "isa7188e *b=n", Setting COM1 Baudrate ,n = 0~9, n=4(default) i-7188E> isa7188e *b=4 Set Com1 Baudrate to 19200 The setting for com1 baudrate are as follows : 1=2400,2=4800,3=9600,4=19200(default), 5=38400,6=57600,7=115200,8=300,9=600,0=1200 To burn an ISaGRAF embedded driver, follow the following steps. 10. Power off the I-7188EG controller, connect pin "INIT*" to "GND" and then power it up. 11. Press "F4" to auto dowload "autoexec.bat","isa7188e.exe","e-060915.img" and reboot system. Wait about 60 SEC. to update ISaGRFA system. ***DO NOT REMOVE THE POWER IN THESE 60 SEC.*** 12. Type "dir" to make sure "autoexec.bat" and "isa7188e.exe" are well burned. i-7188E> dir 0)autoexec.bat 09/16/2005 21:42:13 19[00013]8002:0000-8003:0003 1)isa7188e.exe 10/29/2010 10:46:28 174633[2AA29]8005:0003-AAA7:000C Total File number is 2 Free space=284004 bytes 13. Press ALT_X to exit "7188xw". 14. Remove the connection between "INIT*" - "GND", reset the I-7188EG.Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.