DIAG19x.TXT Driver File Contents (LAN_all.zip)

===========================================================
   SiS PCI Giga Ethernet Adapter Diagnostic Program v2.30
===========================================================
This Diagnostic program contains the following functions:

   1. Adapter Information
   2. Diagnostic Tests

(1). Adapter Information

     1.1 Display Adapter Information, including
         Chip ID           0190 (or 0191)
         Node ID           00 XX XX XX XX XX
         Bus Mode          PCI 32-bit
         Media type        100 Full Duplex
         I/O Base Address  e000
         Interrupt Number  000b
         PHY Address       X                                          
         MII ID            XXXX XXXX
         Msater Bus        Enable

     1.2 Set Media Type -- User can select one of the following
         media type here. Once the media type is selected, the
         latter Diagnostic Tests will be run with this media type.
	 Diag will auto detect the link speed and duplex mode 
         when "Auto Config" is selected.
         Note that the operating speed of 1000Mbps cannot be forced. 
         The link with 1000Mbps only created with auto-detected, 
	 when the link partners both have 1000Mbps capability.
         
         Auto Config
         10 Mbps Half
         10 Mbps Full
         100 Mbps Half
         100 Mbps Full

                         
(2). Diagnostic Tests

     Basic Tests : Include following 3 basic tests.
                          PCI registers I/O test
                          MAC registers I/O test
                          MII registers I/O test


     Controller Loopbacks : Test MAC internal loopback mode.
	
     External Loopback : Type "Diag19x /e", then the item of external loopback will show up 	    	

    
     Send Magic Packet  : Specify Destination Address and Send a
                            magic packet to wake-up other PC.

     Send Wake-up Frame : Specify wake-up frame to wake-up other
                            PC.

     Set Wake-up Event  : Set wake-up event to SIS LAN adapter.

         (Note) After you Set wake-up event, you can turn off the power
                by press power button. Then wait for wake-up event.

     2 Station Test : To run this test, you need two station, Sender and
                      Reponder, connected with an ethernet cable. 

            Sender   : Send packet and wait for response
            Responder: Listen packet from sender and send response to sender

     =========================
     Steps To test wake-on LAN
     =========================
     0. Enable the PM Wake Up Events "MACPME" in the "Power Management Setup" of BIOS option.

     1. Test Wake-up frame

      PC1 that will be waked up                PC2 that will wake up PC1
      (This M/B should support
      Ring-in or Wake-on-LAN)
      -----------------------------            --------------------------
      a. Select "Set wake-up Event"            a. Wait until PC1 is ready
      b. Set wake-up Frame and                 b. Send wake-up frame
         byte mask
      c. Power off
      d. Wait for PC2 to wake me
         up

     2. Test Magic Packet

      PC1 that will be waked up                PC2 that will wake up PC1
      -----------------------------            -------------------------
      a. Select "Set wake-up Event"            a. Wait until PC1 is ready
      b. Set Magic Packet                      b. Send Magic Packet
      c. Power off                                (Destination Address
      d. Wait for PC2 to wake me                   must be PC1 MAC addr)
         up

     3. Test Link Change

      PC1 that will be waked up
      -----------------------------

      a. Select "Set Wake-Up Event"
      b. Select "Link Change"
      d. Power off
      e. change the condition of network-connection.
         (Link on / Link off)


     =========================
     How to Set wake-up Frame
     =========================
     SiS190/SiS191 supports 8 wake-up frames.
     Each Wake-up frame is up to 128 bytes.


     Frame 1: 00XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
              XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
              XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
              XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX

     BitMask: 1XXXXXXXXXXXXXXXXXXXXXXXXXXXXX
              XXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
              XXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
              XXXXXXXXXXXXXXXXXXXXXXXXXXXXXX

     Fill frame with any pattern you want.
     Each '1' in Byte mask means byte you want to match.

     Ex.
     Frame X: 00E00600902212345678XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
              XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
              XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
              XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX

     BitMask: 0000001111XXXXXXXXXXXXXXXXXXXX
              XXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
              XXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
              XXXXXXXXXXXXXXXXXXXXXXXXXXXXXX

     This means you want to match byte 6 to 9 -- 12 34 56 78
     Any received packet that matches byte 6 to 9 will be a wake-up
     frame.

Note: If you don't select media type ,
      the default media type is "Auto Config".
      Then all "Diagnostic Tests" will run with "Auto Config".
     
      
Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web4, load: 1.13