README.TXT Driver File Contents (lm560t.zip)

PCMCIA Ethernet/Fax/Modem                                         May 1996

                          Manual Update Supplement

                             !!!!!!Note!!!!!!!

  For a quick start simply run INSTALL.EXE on the root of this Driver disk.

                             !!!!!!!!!!!!!!!!!

This document contains information that supplements the "User's Manual"
and accompanying software. The User's Manual can be found in the root of the
driver disk as MANUAL.TXT.

  Contents
  ÄÄÄÄÄÄÄÄ
        Introduction
        PCMCIA Driver Installation
        Getting Started
        EMM386 Usage with LanModem
        Driver Directory Structure
        Support Options
        Copyrights, Trademarks, and Disclaimers

  Introduction
  ÄÄÄÄÄÄÄÄÄÄÄÄ
        Thank you for purchasing the PCMCIA Ethernet/Fax/Modem PC Card.
        This diskette has network driver support for the PCMCIA
        Ethernet/Fax/Modem PC Card. There is a format change for this driver
        disk. All README's have been reformatted, an easy setup program,
        and consistency on all documentation provided.

        We hope our new readme's and installation will minimize the users
        effort to make our products work. Should you have further
        recommendations please contact the support manager.

  Install PC Card Software Manually
  ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
        The installation software has been carefully designed to detect
        a combination of hardware and software installed on the PC. Proper
        detection will allow the PC's PC Card drivers to enable the
        LanModem. If the installation software fails to complete,
        the enabler will need to be manually copied from the driver disk
        to the PC. The follow the next few steps for instructions

        If Windows for Workgroup 3.11, Windows NT, or Windows 95 are used,
         follow the instructions for installing PC Cards in the
         PC's manual.

        Determine if any third party generic enablers installed on the PC.
         These are identified by a search through the CONFIG.SYS file for
         the following lines:

             Vendor           Device Loaded in CONFIG.SYS
             ---------------  -------------------------------
             Awards Software  DEVICE=C:\CARDWARE\PCENABLE.EXE
             System Soft      DEVICE=C:\CARDSOFT\CARDID.EXE
             Phoenix          DEVICE=C:\PCMPLUS\PCMSCD.EXE

         If one of these exist in your CONFIG.SYS, it can be used to enable
         the PCMCIA Ethernet/Fax/Modem PC Card.  Follow the PCMCIA driver
         installation instructions in the PC's manual.

        If the PC Card drivers do not support multi-function cards, please
         use the included enabler.

            Disable all current PC Card drivers by editing the CONFIG.SYS
             and AUTOEXEC.BAT. If it is necessary to keep these drivers
             for other adapters skip to next section.
            Insert Driver Disk in drive A:.
            Type C: at the command prompt.
            Type MD LMCARD to make a new directory.
            Type COPY A:\ENABLER\*.* C:\LMCARD to copy the enabler to
             your directory.
            Modify the PATH= statement in your AUTOEXEC.BAT to include
             path C:\LMCARD.

             Change From  PATH=<Original Path>
                    To    PATH=<Original Path>;C:\LMCARD

        Use the CARDEN.EXE to enable LanModem when the PC is loading
         Card Services.

  Getting Started
  ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
        For Novell, Lan Manager, and Packet Driver, first insert the
         PCMCIA Ethernet/Fax/Modem PC Card into one of the free PCMCIA
         card slots, remove all other PC Cards from your machine.

        Then insert the "LanModem Drivers Disk" into drive A, and type
         A:\INSTALL at the command prompt.  The installation program
         will copy files to the destination directory and modify your
         related files(CONFIG.SYS, AUTOEXEC.BAT, and NET.CFG).

        For Windows for Workgroup, Windows NT & Windows 95, use the
         "Network Setup" utility provided by windows system to install
         the LanModem. On this disk you will find sub-directories for each of
         the Microsoft products. Each directory has a README.TXT that will
         help install that particular Microsoft product.

        After installation, simply reboot the machine to enable the LanModem.


  EMM386 Usage with LanModem
  ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
        Under PCMCIA all I/O cards (including Ethernet and Modem) must
        be initialized as memory cards and then switched into I/O mode
        operation by an enabler software.

        Therefore, the enabler software (such as CARDEN.EXE) must see the
        PC Card memory when it is executed.  DOS extended memory managers
        such as EMM386 and QEMM take control of the PC memory space which
        effects PC Card initialization.

        There are two solutions available:

            1) Run enabler (CARDEN or existing PC Card drivers + CARDEN)
               before EMM386 or QEMM is loaded.

            2) Exclude at least 4K of memory from EMM386's or QEMM's use.
               An exclusion of X=D000-D3FF will work well.There may also
               be additional exclusions for your PCMCIA drivers, don't
               modify these.

  Driver Directory Structure
  ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
        The network drivers on this disk is organized in the following
        structure. Each directory contains a README.TXT file which
        provides you with detailed installation instructions for drivers
        in that directory:

  LanModem Diskette Release 05/01/96
  ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
        CARDEN.EXE    Direct PCMCIA Card Enabler for DOS, supports
                      LanModem and Intel compatible, Compaq and Databook
                      controllers.
        LMODI.COM     LanModem DOS/ODI Driver working with direct enabler(LAN
                      & MODEM run concurrently). Supports Intel compatible,
                      Compaq and Databook controllers.
        LMNDIS.DOS    LanModem DOS real mode NDIS Driver
        LMPD.COM      LanModem DOS real mode Packet Driver
        LMNDIS.386    LanModem Enhance Mode NDIS Driver for Win for Workgroups
        LMNDIS.SYS    LanModem Enhance Mode NDIS Driver for Windows 95.
        LMNDIS.SYS    LanModem Enhance Mode NDIS Driver for Windows NT.

  Support Options
  ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
        We are consistently improving and upgrading our drivers. you are
        welcomed at any time to browse through our BBS, and download any
        drivers, utilities and help files.

        If you still cannot get the LanModem working properly, our
        technical experts are always ready to help.  Please be at your
        computer, have your LanModem, Drivers Disk, and the following
        information available:

        * Version number of CARDEN.EXE and any drivers you are running
        * The extact text of any error message displayed on your screen
        * The type of computer
        * The type of network

  Copyrights, Trademarks, and Disclaimers
  ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
    All references to MS, Windows, Win95, Windows 95, Windows NT, WinNT
    are rights reserved by Microsoft Corporation

    All references to Nvl., ODI, Netware, NW, IPX, IPXODI, and LSL are
    rights reserved by Novell Corporation

    Further rights reserved to their respective corporations
Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web5, load: 0.81