-------------------------------------------------------------------------------- - Readme for Dtu2xx Linux device driver -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- - Table of Contents -------------------------------------------------------------------------------- 1. Version History 2. Introduction 3. Installation Instructions 4. Usage Instructions 5. Contact Information -------------------------------------------------------------------------------- - 1. Version History -------------------------------------------------------------------------------- Date: Version: Remarks: 2010.06.22 3.2.0.35 - Support for DTU-215 2010.03.22 3.1.1.32 - Fixes compile issues on kernels v2.6.28 & v2.6.31 2009.01.27 3.1.0.30 - Support for 64-bit kernels - Includes firmware version 9 for DTU-205/225/245 2008.06.30 3.0.1.28 - Fixed fault in Dtu2xxRxIoCtlBulkRead (failed to copy data to user buffer) 2008.05.21 3.0.0.27 - First release of version 3 driver. NOTE: Version 3 is a completely rewritten driver and is not backwards compatible with PRE V4 DTAPI versions - Includes firmware version 8 for DTU-205/225/245 -------------------------------------------------------------------------------- - 2. Introduction -------------------------------------------------------------------------------- The Dtu2xx driver is a char driver for DekTec's DTU-2XX series of USB devices. Currently the driver provides support for the following devices: - DTU-205 (FantASI USB-2 ASI/SDI Output Adapter) - DTU-225 (FantASI USB-2 ASI/SDI Input Adapter) - DTU-234 (USB-2 8-VSB/QAM-B Receiver) - DTU-235 (USB-2 DVB-T Receiver) - DTU-245 (FantASI USB-2 ASI/SDI Input + Output Adapter) -------------------------------------------------------------------------------- - 3. Installation Instructions -------------------------------------------------------------------------------- Compile and install the driver by running 'make install' Then install the module and the udev-rules by running: ("sh ./InstallDtu2xx") -------------------------------------------------------------------------------- - 4. Usage Instructions -------------------------------------------------------------------------------- The Dtu2xx driver has the following system requirements: - Kernel version 2.6.8 or higher - Linux hotplug should be installed This driver was tested on Suse Linux 10.3 For easy usage of the driver, DekTec provides the DTAPI wrapper library. The DTAPI hides the complexities of using the driver in a few easy-to-use classes. The DTAPI is included in the Linux SDK. -------------------------------------------------------------------------------- - 5. Contact Information -------------------------------------------------------------------------------- Please find our contact information below: DekTec Digital Video B.V. Van Riebeeckweg 43A 1212 EH Hilversum The Netherlands Tel: +31 (0)35 64 69 210 Fax: +31 (0)35 68 31 015 email: support@dektec.com / info@dektec.com website: www.dektec.com -------------------------------------------------------------------------------- - 6. Pre-version 3 History -------------------------------------------------------------------------------- 2007.09.18 2.2.2.21 Includes firmware version 7 for DTU-205/225/245. This firmware version fixes the following issues: - Sometimes the receive channel fails to lock-on to input signal after issuing a channel reset (225/245) - 32nd bit of clock-reference-counter was stuck to zero (225/245) - Not all bytes in TX-FIFO were reported in the FIFO load (205/245) 2007.05.16 2.2.1.20 Bugfix in VpdRead() and VpdWrite() 2007.03.09 2.2.0.19 Support for DTU-234 and prepared for DTU-235 2007.02.16 2.1.0.18 - Includes final release of firmware version 5 for the DTU-205/225/245 2007.01.24 2.0.3.17 - Fixed system crash/lock-up when trying to transmit via a DTU-245 - Add support for hardware rev. 5 of DTU-205/225/245 2007.01.15 2.0.2.16 Fix kernel oops on usb disconnect (for kernel>=2.6.18) 2006.09.25 2.0.1.15 - Fixed crash in Dtu2xxDevDelete - Clean-up of code and reduced number of files used 2006.08.14 2.0.0.7 Added support for DTU-245, changed to new interface 2005.03.30 1.1.0.6 Fixed bug related to usage count 2004.12.01 1.0.0.4 Initial versionDownload Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.