-------------------------------------------------------------------------------- - Readme for Dta1xxNw Linux device driver -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- - Table of Contents -------------------------------------------------------------------------------- 1. Version History 2. Introduction 3. Installation Instructions 4. Usage Instructions 5. Contact Information -------------------------------------------------------------------------------- - 1. Version History -------------------------------------------------------------------------------- Date: Version: Remarks: 2010.06.26 1.2.1.8 - Fixes memory allignment issue on 64-bit kernels 2009.11.04 1.2.0.7 - Fixes compile issues due to missing link to Dta1xx symbols 2009.01.27 1.1.0.6 - Fixes compile issues on kernel v2.6.26 and later - Support for 64-bit kernels 2008.05.21 1.0.1.3 - Solves compilation error on kernel 2.6.24 - Fixed issue with kernel version 2.6.23: permanent address function support is removed in kernel v2.6.23 2007.12.13 1.0.0.2 - Fixed compile error when compiling for SMP kernel < 2.6.1 - Fixed kernel panic for SMP kernel < 2.6.4 - Fixed checking return value after creating new thread - Fixed enabling multicast IP packet receive. 2007.11.12 0.0.1.1 - Initial version (compiled and tested on version 2.6.19 of the Linux kernel) -------------------------------------------------------------------------------- - 2. Introduction -------------------------------------------------------------------------------- The Dta1xxNw driver is a network driver for DekTec's DTA-1XX series of PCI cards. Currently the driver provides support for the following cards: - DTA-160 (GigE TS-over-IP + 3 ASI Ports for PCI Bus) - DTA-2160 (GigE TS-over-IP + 3 ASI Ports for PCI Express Bus) -------------------------------------------------------------------------------- - 3. Installation Instructions -------------------------------------------------------------------------------- To install this driver, perform the following steps: - Compile the driver (type "make" in the directory containing the makefile); - Install the driver (type "make install" in the directory containing the makefile). NOTE: MAKE SURE THE 'KERNEL_DIR' DEFINE IN THE MAKEFILE SPECIFIES THE CORRECT PATH TO THE KERNEL SOURCES. IF THE SPECIFIED PATH DOES NOT INCLUDE THE KERNEL SOURCES, BUT ONLY THE 'USER' SOURCES THE COMPILER MIGHT GENERATE THE FOLLOWING MESSAGE: "#warning Using kernel headers in userspace" -------------------------------------------------------------------------------- - 4. Usage Instructions -------------------------------------------------------------------------------- To be able to use this network driver, the Dta1xx driver must be installed and loaded. See the README file of the Dta1xx driver for intalling the Dta1xx driver. If the Dta1xx driver is loaded, the network driver can be started using the Dta1xxNwInit script. "sh ./Dta1xxNwInit start" Load the network driver. "sh ./Dta1xxNwInit stop" Unload the network driver. When the Dta1xxNw driver is loaded, and a DTA-160/2160 card is found a new network devices is created. The device name for the network card is dynamically generated and starts with "eth0" for the first network card. The second will be "eth1", etc. The network driver uses the Linux network stack, so the normal linux network functions can be used for enabling and configuring the network driver. After the driver is loaded you can enable the network interface manually by using the standard linux utilities like ipconfig or ip. E.g. for enabling eth0 with a static IP-address of 192.168.10.10 execute the following command: "ipconfig eth0 192.168.10.10 up". For using a dynamic IP-address use a program such as dhclient. E.g. "dhclient eth0" -------------------------------------------------------------------------------- - 5. Contact Information -------------------------------------------------------------------------------- Please find our contact information below: DekTec Digital Video B.V. Van Riebeeckweg 43A 1212 EH Hilversum The Netherlands Tel: +31 (0)35 64 69 210 Fax: +31 (0)35 68 31 015 email: support@dektec.com / info@dektec.com website: www.dektec.comDownload Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.