iwpriv_usage.txt Driver File Contents (ENLWI-N_ENPWI-N_Linux_Driver_2.zip)

iwpriv
=================
This is detailed explanation of each parameters for iwpriv.
Before reading this document, make sure you already read README.

-------------------------------------------------------------------------------------------------------
USAGE:
	iwpriv ra0 set [parameters]=[val]
	
NOTE:
	Execute one iwpriv/set command simultaneously.
	
where		
[parameters]        	[val] 
						{range}
-----------------   	-------------------------------------------------
CountryRegion       	{0~7}
						::Set country region                                   	
						0: 1 ~ 11 ch
						1: 1 ~ 13 ch
						2: 10, 11 ch
						3: 10 ~ 13 ch
						4: 14 ch
						5: 1 ~ 14 ch
						6: 3 ~ 9 ch
						7: 5 ~ 13 Channel
											
CountryRegionForABand	{0~10}
						::Set country region for A band  										                                       
       						0: 36, 40, 44, 48, 52, 56, 60, 64, 149, 153, 157, 161, 165 ch
						1: 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140 ch
						2: 36, 40, 44, 48, 52, 56, 60, 64 ch
						3: 52, 56, 60, 64, 149, 153, 157, 161 ch
						4: 149, 153, 157, 161, 165 ch
						5: 149, 153, 157, 161 ch
						6: 36, 40, 44, 48 ch
						7: 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165 ch
						8: 52, 56, 60, 64 ch
						9: 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140 ch
                                                           
SSID                	{0~z, 1~32 ascii characters} 			
                    	::Set AP SSID
                    	
WirelessMode        	{0~10}
						::Set Wireless Mode								 
                    	0: legacy 11b/g mixed 
						1: legacy 11B only 
						2: legacy 11A only
						3: legacy 11a/b/g mixed
						4: legacy 11G only
						5: 11ABGN mixed
						6: 11N only
						7: 11GN mixed
						8: 11AN mixed
						9: 11BGN mixed
	   				   10: 11AGN mixed	
                    	
Channel             	depends on CountryRegion or CountryRegionForABand
                        ::Set Channel
                    	
BGProtection        	{0~2}
						::Set 11B/11G Protection                                   	
                   		0:Auto, 
                   		1:Always on, 
                   		2:Always off
                    	
TxPreamble          	{0~2}
						::Set TxPreamble
                    	0:Preamble Long, 
                    	1:Preamble Short, 
                    	2:Auto
                    	
RTSThreshold        	{1~2347}                               	                                                           
                    	::Set RTS Threshold
                    	                                       
FragThreshold       	{256~2346}
						::Set Fragment Threshold                             	
                    	
TxBurst             	{0,1}
						::Set TxBurst Enable or Disable                                  	
                  		0:Disable, 
                  		1:Enable

NetworkType	    		{Infra,Adhoc}
    					::Set Network type
    					 									                                                                                                                                                        	                                                          
AuthMode            	{OPEN,SHARED,WEPAUTO,WPAPSK,WPA2PSK,WPANONE}
                        ::Set Authentication Mode 	

EncrypType          	{NONE,WEP,TKIP,AES}          			
						::Set Encryption Type
						 
DefaultKeyID        	{1~4}                              		
						::Set Default Key ID
						
						
Key1                 	{5 ascii characters or 10 hex number or 
                     	13 ascii characters or 26 hex numbers}
                     	::Set Key1 String                                                                                                                        

Key2                 	{5 ascii characters or 10 hex number or 
                     	13 ascii characters or 26 hex numbers}                                                                                                                        
                      	::Set Key2 String
                      	           	
Key3                 	{5 ascii characters or 10 hex number or 
                     	13 ascii characters or 26 hex numbers}                                                                                                                        
						::Set Key3 String
						 
Key4                 	{5 ascii characters or 10 hex number or 
                     	13 ascii characters or 26 hex numbers}                                                                                                                        
                        ::Set Key4 String
                                                        
WPAPSK              	{8~63 ascii or 64 hex characters} 		 
						::WPA Pre-Shared Key
                    																		
WmmCapable				{0,1}
						::Set WMM Capable
						0:Disable WMM, 
						1:Enable WMM

PSMode					{CAM, MAX_PSP, FAST_PSP}
						::Set Power Saving Mode

HtBw					{0,1}
						::Set BandWidth
						0: 20Hz
						1: 40Hz

HtMcs					{0 ~ 15, 33}
						::Set MCS
						33: Auto Rate

HtGi					{0,1}
						::Set Guard Interval(GI)
						0: long GI
						1: short GI

HtOpMode				{0,1}
						::Set HT Operation Mode
						0: HT mixed format
						1: HT greenfield format

HtExtcha				{0,1}
						::Set Extended Channel Switch Announcement
						0: Below
						1: Above

HtMpduDensity			{0 ~ 7}
						::Set The Minimum Time Between MPDUs within an AMPDU

HtBaWinSize				{1 ~ 64}
						::Set BA WinSize

HtRdg					{0,1}
						::Set RDG Capable
						0: Disabled
						1: Enabled

HtAmsdu					{0,1}
						::Set AMSDU Capable
						0: Disabled
						1: Enabled

HtAutoBa				{0,1}
						::Set Auto BA Capable
						0: Disabled
						1: Enabled

HtProtect				{0,1}
						::Set HT Protect Capable
						0: Disabled
						1: Enabled

FixedTxMode				{CCK, OFDM}
						:: Set Fixed Tx Mode for fixed rate setting
						Mode = CCK
						MCS = 0		=> 1Mbps
							= 1		=> 2Mbps
							= 2		=> 5.5 Mbps
							= 3		=> 11 Mbps
						Mode = OFDM
						MCS = 0		=> 6Mbps
						 	= 1		=> 9Mbps
							= 2		=> 12Mbps
							= 3		=> 18Mbps
							= 4		=> 24Mbps
							= 5		=> 36Mbps
							= 6		=> 48Mbps
							= 7		=> 54Mbps

Examples
===================================================================
-------------------------------------------------------------------------------------------------------
a> Config STA to link with AP which is OPEN/NONE(Authentication/Encryption)
	1. iwpriv ra0 set NetworkType=Infra
	2. iwpriv ra0 set AuthMode=OPEN
	3. iwpriv ra0 set EncrypType=NONE
	4. iwpriv ra0 set SSID="AP's SSID"
	
b> Config STA to link with AP which is SHARED/WEP(Authentication/Encryption)
	1. iwpriv ra0 set NetworkType=Infra
	2. iwpriv ra0 set AuthMode=SHARED
	3. iwpriv ra0 set EncrypType=WEP
	4. iwpriv ra0 set DefaultKeyID=1
	5. iwpriv ra0 set Key1="AP's wep key"
	6. iwpriv ra0 set SSID="AP's SSID"
	
c> Config STA to link with AP which is WPAPSK/TKIP(Authentication/Encryption)
	1. iwpriv ra0 set NetworkType=Infra
	2. iwpriv ra0 set AuthMode=WPAPSK
	3. iwpriv ra0 set EncrypType=TKIP
	4. iwpriv ra0 set SSID="AP's SSID"
	5. iwpriv ra0 set WPAPSK="AP's wpa-preshared key"
	6. iwpriv ra0 set SSID="AP's SSID"
	
d> Config STA to link with AP which is WPAPSK/AES(Authentication/Encryption)
	1. iwpriv ra0 set NetworkType=Infra
	2. iwpriv ra0 set AuthMode=WPAPSK
	3. iwpriv ra0 set EncrypType=AES
	4. iwpriv ra0 set SSID="AP's SSID"
	5. iwpriv ra0 set WPAPSK="AP's wpa-preshared key"
	6. iwpriv ra0 set SSID="AP's SSID"

e> Config STA to link with AP which is WPA2PSK/TKIP(Authentication/Encryption)
	1. iwpriv ra0 set NetworkType=Infra
	2. iwpriv ra0 set AuthMode=WPA2PSK
	3. iwpriv ra0 set EncrypType=TKIP
	4. iwpriv ra0 set SSID="AP's SSID"
	5. iwpriv ra0 set WPAPSK=12345678
	6. iwpriv ra0 set SSID="AP's SSID"
	
f> Config STA to create/link as adhoc mode, which is OPEN/NONE(Authentication/Encryption)
	1. iwpriv ra0 set NetworkType=Adhoc
	2. iwpriv ra0 set AuthMode=OPEN
	3. iwpriv ra0 set EncrypType=NONE
	4. iwpriv ra0 set SSID="Adhoc's SSID"

g>  Config STA to create/link as adhoc mode, which is WPANONE/TKIP(Authentication/Encryption)
    1. iwpriv ra0 set NetworkType=Adhoc
	2. iwpriv ra0 set AuthMode=WPANONE
	3. iwpriv ra0 set EncrypType=TKIP
	4. iwpriv ra0 set SSID="AP's SSID"
	5. iwpriv ra0 set WPAPSK=12345678
	6. iwpriv ra0 set SSID="AP's SSID"
  
h> Get site survey 
	usage: iwpriv ra0 get_site_survey
		
i> Get Statistics 
	usage: iwpriv ra0 stat						; read statistic counter
		   iwpriv ra0 set ResetCounter=0		; reset statistic counter

j> Link with an AP which is the largest strength   ; set ANY SSID (ssidLen=0)
   usage: iwconfig ra0 essid ""                 
   or
   usage: iwpriv ra0 set SSID=""
===================================================================

iwlist
=================
This is detailed explanation of each parameters for iwlist.

-------------------------------------------------------------------------------------------------------
iwlist ra0 scanning		; list the results after scanning(manual rescan)



=======================================================================================================

iwconfig
=================
The following are our support in standard configuration - iwconfig

-------------------------------------------------------------------------------------------------------
iwconfig ra0 essid {NN|on|off}			; set essid
iwconfig ra0 mode {managed|ad-hoc|...}  ; set wireless mode
>> rt2860sta driver support monitor mode with linux kernel > 2.4.20.
iwconfig ra0 freq N.NNNN[k|M|G]]		; set frequency
iwconfig ra0 channel N					; set channel
iwconfig ra0 ap {N|off|auto}			; set AP address
iwconfig ra0 nick N						; set nickname
iwconfig ra0 rate {N|auto|fixed}     	; set rate
iwconfig ra0 rts {N|auto|fixed|off}		; set RTS threshold
iwconfig ra0 frag {N|auto|fixed|off}	; set Fragment threshold
iwconfig ra0 enc {NNNN-NNNN|off}		; set encryption type
iwconfig ra0 power {period N|timeout N}	; set power management modes

*** Wireless extension usage please refer to man page of 'iwconfig', 'iwlist' and 'iwpriv'. ***
Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web3, load: 0.68