release.txt Driver File Contents (V08809.zip)

; AST VBIOS Release Notes
;===============================================================================
v.0.50.00: ycchen@10122005
1. The first release for A0
---------------------------------------------------------------------------------       
v.0.51.00: ycchen@10252005
1. [Bug] Fixed ReadHat9 Install Shell Display Abnormal Issue
2. [New] Modify for DRAM init status check in UMA mode
3. [New] Support Customizded DRAM timing in binary level
4. [New] Support Virtual EDID
5. [Bug] Install RHEL hanged before enter into X-Window on Operon
6. [Bug] Modify for CRTC Timing for standrad mode & low resolution mode
7. [New] Add Support VESA Mode: 1280x1204, 1600x1200, 320x240, 400x300 and 512x384
---------------------------------------------------------------------------------       
v.0.52.00: ycchen@11042005
1. [New] Change Device to 0x1A03
---------------------------------------------------------------------------------       
v.0.60.00: ycchen@12202005, first release for A1    
001.[New] Modify for A1 support
002.[New] Integrate LFB/UMA VBIOS into one (ASTVBIOS.ROM)
---------------------------------------------------------------------------------       
v.0.61.00: ycchen@011106   
001.[Bug] fixed VRS/VRE incorrect issue, ycchen@122805
002.[New] 32k VBIOS as default
003.[New] Modify for product description
004.[New] Support 16/32 DRAM in one VBIOS
005.[Bug] Can't Set VESA Mode: 1280x1024x32bpp, ycchen@010606
006.[Bug] 640x480x72Hz Border issue
007.[Bug] Modify for low-reslution timing, ycchen@011005
008.[Bug] fixed AMIDIAG\VESA memory test failed issue, ycchen@011206
009.[Bug] Modify for CRTC timing for STD. mods, ycchen@011206
---------------------------------------------------------------------------------       
v.0.62.00: ycchen@020606            
001. [Patch] QCI LCD Monitor display dummy under the bottom of the screen
---------------------------------------------------------------------------------       
v.0.63.00: ycchen@020906         
001. [Bug] Run PCDR/Video memory test cause KVM crash
---------------------------------------------------------------------------------       
v.0.80.00: ycchen@031306        
001.[BUG] Fixed PCDR/AMIDIAG/BCMDIAG RAMDAC Test too long issue, ycchen@030606                
002.[PATCH] Fixed ARC1220 RAID controller display message abnormal issue, ycchen@031006
---------------------------------------------------------------------------------       
v.0.81.00: ycchen@042406                       
001.[New] Set MCLK166 as default, ycchen@042406
v.0.81.01: ycchen@051106                       
001.[Bug] Fixed save/restore PLL setting incorrect by ycchen@051106
---------------------------------------------------------------------------------       
v.0.82.00: ycchen@061406
001. Bump Version Only
v.0.82.00b: ycchen@092906
001.[New] Initial VGA only if Class Code is VGA Device, ycchen@091506
002.[New] Add the support for VGA initial SOC RTC
003.[New] Add scratch for scan line infor, ycchen@092906
---------------------------------------------------------------------------------       
v.0.83.00: ycchen@120406
001.[New] Support AST2100 FPGA EVB Board
v.0.83.01: ycchen@011207
001.[New] Modify for AST2100 New IP (0606)
002.[Bug] Fix BCMDiag video memory test failed, ycchen@011206
v.0.83.02: ycchen@020607
001.[Bug] Fix CMDQ & MMIO CMD reorder issue
v.0.83.03: ycchen@021607
001.[Bug] Fix AST2100 VGA & Video Threshold Issue, ycchen@02160
v.0.83.04: ycchen@051507
001.[Bug] Fixed bug check 0xf7 in vista64
---------------------------------------------------------------------------------       
v.0.84.00: ycchen@060507        
01.[New] Support AST2100 A0, ycchen@053107
02.[New] Support 1920x1200x60Hz for AST2100, ycchen@060407
v.0.84.01: ycchen@060807        
01.[New] Remove Chrontel Setting for real chip
02.[New] Use 512Mb x32 setting as default DRAM type
v.0.84.02: ycchen@061507        
01.[Bug] Fixed 1920x1200x60Hz can't display
02.[New] Modify DRAM timing by H/W request
v.0.84.03: ycchen@062107
01.[New] Modify DRAM timing to 266MHz
v.0.84.04: ycchen@070907
01.[New] Modify DRAM timing for H/W request
v.0.84.05: ycchen@072607
01.[New] Disable ReadCache for AST2100 by H/W request
02.[New] Set VGA DRAM Trapping to DRAM Controller, ycchen@072607
---------------------------------------------------------------------------------       
v.0.85.00: ycchen@103107
01.[New] Modify 1920x1200x60Hz to reduced blank mode, ycchen@081307
02.[New] Support ECC
03.[Bug] Fixed PCCheck VGA Palette Test Failed Issue, ycchen@103107
04.[Bug] Fixed Scanline info incorrect in scratch, ycchen@103107
05.[Patch] Patch WDT can't detect mode change properly, ycchen@103107
06.[New] Set Scratch after DRAM Initial
07.[New] Enable Read Cache for AST2100 A1
v.0.85.01: ycchen@112707
01.[New] Modify DRAM timing by H/W request (11/08/07)
02.[Bug] Fixed display abnormal while new PLL modes change to standard modes, ycchen@112807
03.[New] Remove 1920x1200 for AST1100
04.[New] Modify Display banner for AST1100/2050/2100
05.[Bug] Change 1920x1200x60Hz's polarity to NP
v.0.85.02: ycchen@121207
01.[Bug] Fixed DCT/SVGA/INT10 failed issue
02.[New] Modify DDR 512x16 200MHz parameters by H/W  request
v.0.85.03: ycchen@010308
01.[New] Modify for DDR 512x16 200MHz settings
---------------------------------------------------------------------------------       
v.0.86.00: ycchen@012808
01.[New] Modify DRAM settings by H/W (01108)
v.0.86.04: ycchen@032108
01.[Bug] Fixed the background color of edit is incorrect after run cls, ycchen@032108
v.0.86.09: ycchen@051208
01.[New] Add DDR2 1Gx16 200MHz support
v.0.87.00: ycchen@072908
01.[PATCH] Patch for AST2100/1100 A2 X-Window Compatible Issue, ycchen@072908
---------------------------------------------------------------------------------       
v.0.88.00: ycchen@082808
01.[BUG] Fixed VGA2 Mirror Display on board solution can't work properly in Windows, ycchen@082708
v.0.88.01: ycchen@090208
01.[New] Add AST1100/2050/2100 A2 Chip Identity, ycchen@090108
02.[New] Modify AST1100/2050/2100 DDR2 DRAM Timing by Jason's Request
v.0.88.02: ycchen@090908
01.[New] Bump Version for AST1160
v.0.88.03: ycchen@100208
01.[Bug] Fix DELL RBU cause display blank issue, ycchen@100208
02.[New] Modify for the request of recovery BIOS by QCI
03.[Bug] Modify AST2100 DRAM timing for unstable issue (restore to v.0.88.01)
v.0.88.04: ycchen@101408
01.[New] Add AST2100 DVO Support, ycchen@100808
02.[Bug] Fixed code error in SetWriteBank & SetReadBank, ycchen@101408
03.[New] Modify DRAM Reg. Settings by H/W  Request, ycchen@102808


 
  
Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web3, load: 2.37