Server Driver for NetWare 3.12
Introduction:
-------------
This document describes the procedure to install the NetWare V3.12
server driver for D-Link DFE-690TXD CardBus PC Card.
Location of Driver: \NWSERVER\312\DLKRCB.LAN
Getting Start:
--------------
1. For the PC that installing EMM386.EXE in the CONFIG.SYS.
Please make sure the memory range D000-D7FF is excluded.
Ex:
DEVICE=C:\DOS\EMM386.EXE NOEMS X=D000-D7FF
2. Copy <PATH>\ENABLER\*.* files from released disk into your
hard disk.
Ex:
copy E:\ENABLER\*.* C:\ENABLER
3. Add a line
@CALL C:\ENABLER\CBEN.BAT
on the first line of AUTOEXEC.BAT file.
Installation Procedure:
-----------------------
Before you start with the installation process, make sure that
the Novell NetWare v3.12 server is properly installed.
Similarly, your adapter should also be properly installed in your server.
1. Make a sub-directory NLMS.OLD under <SRVPATH> directory which
includes SERVER.EXE.
Ex. <SRVPATH> = SRV312.
>MD \SRV312\NLMS.OLD
2. Save NBI.NLM, MSM.NLM and ETHERTSM.NLM to NLMS.OLD
sub-directory.
3. Insert driver disk into CD-ROM drive.
4. Copy all provided NLM and LAN files into your dos directory
which includes SERVER.EXE, and rename NBI31X.NLM and MSM31X.NLM :
Ex. >COPY E:\NWSERVER\312\NBI31X.NLM C:\SRV312\NBI.NLM
>COPY E:\NWSERVER\312\MSM31X.NLM C:\SRV312\MSM.NLM
>COPY E:\NWSERVER\312\ETHERTSM.NLM C:\SRV312
>COPY E:\NWSERVER\312\DLKRCB.LAN C:\SRV312
5. Start the NetWare Server.
> CD \SRV312
> SERVER
6. From the Novell Server side, execute "LOAD INSTALL". Type:
LOAD INSTALL
Select <System Options>
Select <Edit AUTOEXEC.NCF File>
7. Add the following commands into the server's AUTOEXEC.NCF file.
Search Add C:\SRV312
LOAD NBI.NLM
LOAD MSM.NLM
LOAD ETHERTSM.NLM
LOAD DLKRCB SLOT=1 FRAME=Ethernet_802.3 NAME=DLKRCB_1_E83
BIND IPX DLKRCB_1_E83 NET=1111
LOAD DLKRCB SLOT=1 FRAME=Ethernet_802.2 NAME=DLKRCB_1_E82
BIND IPX DLKRCB_1_E82 NET=1113
LOAD DLKRCB SLOT=1 FRAME=Ethernet_SNAP NAME=DLKRCB_1_ESP
BIND IPX DLKRCB_1_ESP NET=1115
LOAD DLKRCB SLOT=1 FRAME=Ethernet_II NAME=DLKRCB_1_EII
BIND IPX DLKRCB_1_EII NET=1117
Note: The SLOT parameter should be set as the number of the PCI slot
on which DFE-690TXD resides.
8. Restart the server again.
NOTES:
------
1. Installing Multiple LAN Adapters:
The keyword "SLOT" is provided for multiple LAN adapters in a
single server by the driver DLKRCB.LAN. So, add "SLOT" in LOAD
commands. For example:
LOAD DLKRCB SLOT=1 FRAME=Ethernet_802.2 NAME=LAN_A
BIND IPX TO LAN_A NET=111
LOAD DLKRCB SLOT=2 FRAME=Ethernet_802.2 NAME=LAN_B
BIND IPX TO LAN_B NET=222
2. Use keyword AUTO, 100FULL, 100HALF, 10FULL, 10HALF to specify the
media type of the DFE-690TXD.
For example:
; Specify AUTO-DETECT
LOAD DLKRCB AUTO FRAME=Ethernet_802.2 NAME=LAN_A
BIND IPX TO LAN_A NET=111
; Specify 100Mbps, Half-duplex
LOAD DLKRCB 100HALF FRAME=Ethernet_802.2 NAME=LAN_A
BIND IPX TO LAN_A NET=111
The default media type is auto-detect(i.e. none of these keywords
is specified).
3. Installing One LAN adapter with Multiple Frame Types:
When binding multiple frame types to one adapter, enter a LOAD
and BIND statement for each frame type. Each LOAD statement will
use a different network number on the bind statement.
It is required to supply a name on each load line in order to avoid
being prompted for which board to bind IPX to. If you do not
have the name option in the AUTOEXEC.NCF, it will not execute
completely without user intervention.
Example:
LOAD DLKRCB FRAME=ETHERNET_802.3 NAME=DLKRCB_1_E83
BIND IPX TO DLKRCB_1_E83 NET=11111
LOAD DLKRCB FRAME=ETHERNET_802.2 NAME=DLKRCB_1_E82
BIND IPX TO DLKRCB_1_E82 NET=33333
LOAD DLKRCB FRAME=ETHERNET_SNAP NAME=DLKRCB_1_ESP
BIND IPX TO DLKRCB_1_ESP NET=55555
LOAD DLKRCB FRAME=ETHERNET_II NAME=DLKRCB_1_EII
BIND IPX TO DLKRCB_1_EII NET=77777
If problems occur during the binding process, your screen will prompt
you with error messages. Please refer to your NetWare 386 manual for
details on these messages.
-- End --
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.