=====================================================================
=====================================================================
DisplayLink Software Release: External Release Note
Software Package: Samsung UbiSync Monitor
Version: 5.1.20072.0
=====================================================================
=====================================================================
EXECUTIVE SUMMARY
This is the R5.1 Product Release. It has completed system test and is
suitable for deployment to end-users.
DisplayLink Software Release 5.1 delivers the following features:
- Faster video performance
- Faster performance with DL1x5 products
- 'Optimize for Video' GUI option
This release is not compatible with MS Windows 7 and will refuse to
install on that operating system. Please visit
http://www.displaylink.com/win7 for DisplayLink Windows 7 drivers.
Please note that the following areas of functionality have undergone
very limited testing and are not recommended:
- Use with over three DisplayLink screens
- Use on Intel/ATI switchable graphics laptops
Recommendations for use:
------------------------
If using with more than one device, make sure each device is fully
installed and working before adding the next.
Minor issues can generally be resolved by
- detaching and reattaching the DisplayLink device
- changing the display mode via the DisplayLink GUI, or
- changing the display mode via Windows Display Properties.
On Windows Vista WDDM (Aero and Basic): DisplayLink software works
closely with the graphics card and there may be interoperability issues
with some graphics cards. If this happens,
(1) try to upgrade to the latest graphics drivers
(2) try to upgrade to latest DisplayLink software
(3) report the issue via your support channel
(4) if necessary, boot into Safe Mode and use Vista's Backup and
Restore Center to recover.
Video: video is supported with most popular video players on Windows
Vista in WDDM/Aero Mode. Video is also supported in Extend mode on
Windows XP. Video support is limited in other configurations including
Windows Vista Basic Mode and mirror mode in Windows XP.
For further support and information about DisplayLink software, please
visit http://www.displaylink.com/support
=====================================================================
=====================================================================
A. Introduction
===============
This is the R5.1 Product Release. It has completed system test and is
suitable for deployment to end-users.
DisplayLink Software Release 5.1 delivers the following features:
- Faster video performance
- Faster performance with DL1x5 products
- 'Optimize for Video' GUI option
This release is not compatible with MS Windows 7 and will refuse to
install on that operating system. Please visit
http://www.displaylink.com/win7 for DisplayLink Windows 7 drivers.
Please note that the following areas of functionality have undergone
very limited testing and are not recommended:
- Use with over three DisplayLink screens
- Use on Intel/ATI switchable graphics laptops
B. Contents
===========
Executive Summary
A. Introduction
B. Contents
C. New features
D. Note on Windows Vista Modes
E. How to Install
F. How to Use
G. Supported Operating Systems
H. PC Minimum Specifications
I. Language Support
J. Supported Hardware
K. Summary of Software State and Issues - Windows Vista WDDM
K1. Windows Vista WDDM graphics card support
K2. Normal use
K3. Video players, rendering technologies and applications
K4. Installer and auto-update function
L. Summary of Software State and Issues - Vista XDDM, XP, 2K
L1. Normal use
L2. Video players, rendering technologies and applications
L3. Installer and auto-update function
M. Driver qualification information
C. New features
===============
DisplayLink Software Release 5.1 delivers the following features:
- Faster video performance
- Faster performance with DL1x5 products
- 'Optimize for Video' GUI option
Faster video performance
------------------------
R5.1 includes specific video playback performance optimisations that
greatly improve the user experience when playing video on DisplayLink
screens.
Faster performance with DL1x5 products
---------------------------------------
This software release takes full advantage of some hardware features
in the DL1x5 family of DisplayLink products that increase the
rendering performance in specific conditions.
'Optimize for Video' GUI option (Vista WDDM only)
--------------------------------------------------
This option in The DisplayLink GUI enables specific optimisations that
can improve video playback performance in certain circumstances.
D. Note on Windows Vista Modes
==============================
Normally, Windows Vista is in WDDM mode. In this mode, Vista graphics
drivers are used, and the Vista Aero Glass and Vista Basic themes are
available.
Windows Vista PCs whose graphics drivers are not Windows Vista native
will run in XDDM (XP-Compatible) mode. In this mode, the 3D Aero Glass
theme is not available. This mode will be limited to PCs that were
upgraded from XP to Vista and PCs with low-end graphics cards.
DisplayLink software supports both modes in different ways, and the
level of support and issues are different in the two cases.
E. How to Install
=================
Important note: users who have v3.x 'USB Display Adapter' software
installed in Add/Remove Programs must uninstall it before installing
this release. Devices using v3.x software will continue working after
this release is installed.
Important note: if you are installing several devices, make sure that
each is fully installed and showing an image before attaching the
next.
Important note: after uninstalling the DisplayLink software a reboot
is required before installing the same or a different version of the
software. Upgrading the software will require a reboot only when
necessary. (5329)
Software-first install
----------------------
- Unzip the release package
- Run 'setup.exe'
- Once installation is complete, attach a DisplayLink device / screen
to the PC and wait for it to come up.
Hardware-first install from release package (.zip)
--------------------------------------------------
- Unzip the release package to a convenient place,
- Connect the DisplayLink device
- Point the 'New Hardware Found' wizard at the unzipped release
package.
Hardware-first install from CD
------------------------------
- Put the CD into the PC's drive
- Connect the DisplayLink device / screen
- Point the 'New Hardware Found' wizard at the CD drive.
Uninstalling the Release
------------------------
- Go to 'Add or Remove Programs' dialog box (XP or 2K)
- Go to 'Uninstall a Program' or 'Programs and Features' dialog box
(Vista)
- Select the customer product you installed
- Choose 'Remove'.
F. How to Use
=============
DisplayLink screens can run in three modes:
- extend mode: the screen is part of the extended desktop
- mirror mode: the screen copies the contents of the primary screen
- off mode: the screen is black.
Display modes can be controlled through the DisplayLink GUI (DL-GUI)
and through the Windows Display Properties dialog box (WDP).
DisplayLink Manager GUI (System Tray Icon)
------------------------------------------
This is an icon in the systray that looks like a monitor. Click on
the icon to bring up the menu. You can control
- screen resolution
- colour quality
- rotation
- mode (extend, mirror, off, dock)
- extend position (right, left, above, below)
- turn off your notebook monitor
- auto-update configuration
- manual check for newer software
- optimize the software for video playback
Windows Display Properties (WDP)
--------------------------------
To open WDP on XP / 2K
- right-click on the desktop
- select 'Properties' from the context menu
- go to the Settings tab
To open WDP on Vista
- right-click on the desktop
- select 'Personalize' from the context menu
- click on Display Settings link
To open WDP from DL-GUI
- bring up the DL-GUI menu
- click 'Advanced...'
With WDP you can control
- screen resolution
- colour quality
- extend position
- primary screen
- refresh rate
- whether the device is enabled (= part of the extended desktop)
or not (= mirror or off mode).
G. Supported Operating Systems
==============================
This release supports the following operating systems:
- Windows 2000 SP4
- Windows XP SP2
- Windows XP SP3
- Windows Vista SP1 (32-bit and 64-bit editions)
- Windows Vista SP2 (32-bit and 64-bit editions)
H. PC Recommended Specifications
================================
DisplayLink software can be run on PCs ranging from Netbooks (e.g. Asus
EeePC), Notebooks/Laptops, and Desktops - on processors ranging from
Atom N270 based PCs, basic single Core CPUs, and of course the latest
Dual and Quad Core CPUs.
The performance of the software is dependent upon the processing power
available, and so more capable systems offer higher performance.
Recommended typical system requirements are:
Windows Vista
=============
For Windows Vista, the Windows Experience Index (WEI) is a useful
measure of hardware level. The WEI is accessible from
Computer->Properties or from Control Panel->System.
The recommended typical hardware requirements for the PC are
* WEI score of at least 3.0 in the 'Graphics; Desktop performance for
Windows Aero' category.
* Recommended: WEI score of at least 3.0 overall, as recommended by
Microsoft.
* For full-screen video playback the recommended hardware depends on
the display resolution:
* 1366x768: overall WEI score of at least 3.5.
* 1920x1080 (HD): overall WEI score of at least 4.0 and a modern
GPU (GPU introduced to the market after 2H'08 or top-of-the-line
GPU introduced in 2008).
* At least one USB 2.0 port.
* 30 megabytes (MB) of free disk space.
* Computer screen for use with the DisplayLink device, if it is not
integrated.
* Network access for software downloads, or access to a CD-ROM drive.
If the PC specification is below this, performance will be lower (or
CPU loading higher).
Windows XP/2000
===============
* For 1-2 monitors, business usage, productivity target. This may not
provide full frame rate DVD playback at full screen.
- 1.2GHz Single Core CPU (Celeron or Atom N270 for example)
- 512MB memory
* For 3 monitors where 1 could run DVD video while also targeting
productivity and business apps. Will support only 1 video of DVD
resolution at full screen:
- 1.8GHz CPU
- 1GB memory
* For 6 screens where 1 screen can run full screen DVD video:
- 1.6GHz Core Duo
- 1GB memory
I. Language Support
===================
DisplayLink software is localised in the following languages:
- English
- French
- German
- Dutch
- Italian
- Spanish
- Portuguese
- Polish
- Hungarian
- Russian
- Traditional Chinese
- Simplified Chinese
- Japanese
- Korean
J. Supported Hardware
=====================
- DL115 / DL125 / DL165 / DL195 devices are supported.
- DL120 / DL160 devices are supported.
- Earlier devices are supported for backwards compatibility.
This package supports up to 6 devices.
K. Summary of Software State and Issues - Windows Vista WDDM
============================================================
K1. Windows Vista WDDM graphics card support
--------------------------------------------
Because of restrictions in Vista WDDM support for graphics cards, the
DisplayLink software works closely with the graphics drivers for
the PC's graphics card. This software supports interworking with single
graphics cards from Intel, ATI, Nvidia and Via, including NVidia SLI
in SLI mode.
DisplayLink cannot exclude severe problems in the case of graphics cards
or driver versions that have not been interoperability tested with
DisplayLink software. Should such problems arise,
- First, upgrade to the latest graphics drivers for your PC. Latest
drivers can be found on the PC manufacturer's or graphics card
manufacturer's website.
- Second, upgrade to the latest DisplayLink software available for
your device. Use 'Check now...' from the DisplayLink GUI to find and
download latest software.
- If this does not help, please inform your DisplayLink device
manufacturer's support line. Please give these details:
+ PC make, CPU and memory
+ graphics card make, model and driver version.
Known Issues - General
DisplayLink screens are not supported on systems with two graphics
cards used simultaneously (supporting separate screens, or in ATI
Crossfire configuration). Two graphics cards in Nvidia SLI
configuration are supported. (1704, 4441)
DisplayLink software may cause blue screens on software configurations
where WDDM drivers from different manufacturers have been installed on
the same system, even if just one graphics card is present. (4323)
On Vista WDDM, TMM does not appear when DisplayLink screens are
attached. It works normally when no DisplayLink screens are
attached. (2569)
On some systems with switchable graphics architectures a maximum of 3
DisplayLink screens is supported when in High Performance GPU mode.
(4459)
On a switchable graphics machine with DisplayLink software installed do
not change the bios settings to ATI only or Intel only.
If you need to change those BIOS settings please first uninstall the DL
software, then reinstall it once the new settings have been applied.
(4339, 4506)
On Vista WDDM, very occasionally, if the DisplayLink screen is primary
with the main screen off, then the DisplayLink screen flashes
continuously when resuming from hibernation. To cure the problem,
detach and re-attach the DisplayLink screen. To prevent the problem,
set the PC to require a password when coming out of hibernation. (2835)
On Vista WDDM, very occasionally, if the DisplayLink screen is primary
with the main screen off, then both the main and DisplayLink screens
may show corruption when resuming from hibernation. To cure the problem,
enable and disable the main screen. (3219)
On Vista WDDM aero, DisplayLink software can cause some PCs to become
more susceptible to TDRs (Timeout Detection and Recovery). More info
at http://www.microsoft.com/whdc/device/display/wddm_timeout.mspx.
Suggested workarounds are (1) upgrade to the latest drivers for the
native graphics card; (2) increase TDR timeouts as described in the
linked article. (3217)
Corruption can sometimes be seen around the mouse pointer on rotated
DisplayLink screens. (5564)
Known Issues - Intel GMA Integrated Graphics
Some older versions of Intel GMA drivers will cause corruption on
the DisplayLink screen. The solution is to upgrade them to version
7.14.10.1111 or later. This is with Vista WDDM. (2164)
Users of Vista WDDM with Intel graphics should exercise caution if
using two or more DisplayLink screens at a time. Very occasionally,
mode changes or detach/reattach of two DisplayLink devices at once
has been observed to cause a complete machine lock-up. (2264)
On Vista WDDM systems with Intel 945GM graphics and with graphics
driver versions around 7.14.10.1461 and 7.14.10.1504, playing a video
on a DisplayLink attached screen can cause the whole system to run
very slow. A reboot is needed to resolve this. To avoid the problem,
do not play video on such DisplayLink screens, or downgrade the
graphics drivers. (3076)
On Vista WDDM, some computers with Intel graphics reset DisplayLink
screens from extend to mirror when coming out of sleep. A workaround
is to disable the Intel persistence application, by removing
HKLM\Software\Microsoft\Windows\CurrentVersion\Run\Persistence
(The normal value would be C:\windows\system32\igfxpers.exe). (2546)
DisplayLink software is currently compatible with Intel/ATI switchable
graphics architectures (with limited testing). Nvidia switchable
graphics platforms are not supported yet. (3068)
Vista WDDM Aero is not currently supported on Intel GMA 500 graphics
chipsets: DisplayLink software may cause blue screens on such systems.
Please switch to Basic mode before using DisplayLink devices with Intel
GMA 500 hardware. (5192)
Known Issues - ATI graphics
The ATI Catalyst Control Center is a tool provided by ATI to control
ATI graphics cards. In the presence of DisplayLink attached screens,
some parts of the tool, such as its adjustments submenu, do not work.
This is on all OSes. (1596)
Some versions of the ATI Catalyst Control Center crash in the
presence of DisplayLink software. This has been observed with versions
since ATI driver version 8.360. This can cause problems when a
screen is attached to the PC. To work around the problem, uninstall the
ATI Catalyst Control Center.
On Vista WDDM with ATI graphics, the ATI External Event Utility can
interfere with remembered settings for DisplayLink screens. To avoid
this, disable the ATI External Event Utility as follows: Navigate to
Control Panel -> System and Maintenance -> Administrative Tools ->
Services: Ati External Event Utility and change the startup type to
Disabled. (2674)
Known Issues - Nvidia graphics
On Vista WDDM, Nvidia driver versions earlier than 7.15.10.7500 or
7.15.11.7500 exhibit slowness on DisplayLink screens on some PCs. To
fix this, please upgrade to more recent Nvidia graphics drivers. (2282)
With Vista, a maximum of four DisplayLink screens are supported on
machines with Nvidia graphics. In certain rare cases, exceeding this
has been seen to cause repeated serious crashes. (1781)
On Vista WDDM, older versions of Nvidia drivers with versions prior to
7.15.11.146 can behave badly in the presence of DisplayLink software.
For instance they can cause blue screens when applications are
maximised on DisplayLink screens. Also, if DisplayLink devices are
attached or detached during restart, it may be necessary to press the
reset button on the PC to restore normal functioning. (2119)
On Vista WDDM, Nvidia 5 series graphics cards with driver version
7.15.10.9685 cause rundll32 crash messages in the presence of
DisplayLink software. If you have such a card, please update to a
more recent graphics driver version. (3077)
On some Nvidia SLi systems, it is not possible to enable or disable
SLi mode while a DisplayLink screen is attached. (3147)
Triple SLi systems are not supported. (3146)
DisplayLink software is currently compatible with Intel/ATI switchable
graphics architectures (with limited testing). Nvidia switchable
graphics platforms are not supported yet. (3068)
K2. Normal use
--------------
System behaviour with DisplayLink attached screens has been well
tested. Testing covers plug/unplug, mode changes, playing video,
hibernate, sleep/standby, multiple users, different user rights,
attached screen as primary screen, attached screen as only screen,
and other aspects.
There are many minor issues. General recommendations if something
goes wrong:
- detach then reattach the DisplayLink device's USB cable
- change display settings using DL-GUI
- change display settings using WDP.
Known Issues - Hibernate / sleep / monitor power save / screensavers
On Vista, very occasionally, DisplayLink devices fail to resume from
hibernation or sleep. This is due to issues in the Vista USB subsystem.
Hotfix http://support.microsoft.com/kb/941600 should help. This is
believed to be fixed in Vista Service Pack 1. (2126)
On Vista WDDM, DisplayLink attached screens can be slow when resuming
from hibernation or sleep. This is a Vista problem and is believed to
be improved in Vista Service Pack 1. (2165)
On all OSes, the desktop background is occasionally missing after
restart or after resume from sleep or hibernation. The screens are
still usable, and the background can be set again to the desired
picture. (2154, 2072)
On all OSes, detaching or attaching DisplayLink attached screens while
a screensaver is running may cause strange effects. Sometimes it is
necessary to detach and reattach the DisplayLink attached screen after
exiting the screensaver. (1984)
3D screensavers do not run well on DisplayLink devices and can cause
flicker and/or decreased graphics performance. This is on all OSes.
(1150, 1177, 4426)
If devices are detached from the PC before going into standby, then
reattached during standby, very occasionally they may not resume when
the PC comes out of standby. If this happens, detach and reattach the
devices to make them work again. (1492)
Known Issues - Other
In PowerPoint, the "Display slide show on:" menu has a bug which means
that it does not work when there are gaps in the numbering of enabled
displays (as shown in WDP). Users of PowerPoint 2007 can get round this
by using "Show presentation on:" in the ribbon, rather than the "Set
up slide show" box. (2337)
CRT monitors may show speckles at very high resolutions. This is
because the DisplayLink device cannot always support the high pixel
clock required with high CRT refresh rates. (2155)
After a reboot, the numbers used in Windows Display Properties to
identify the attached screens may change. This is normal. (596)
When using a display in mirror mode, changing the rotation setting can
cause the display to go into extend mode. Setting the display back to
mirror mode will show the correct rotation. (2261)
Occasionally, on rotating a DisplayLink screen the monitor may freeze,
change resolution or go black. This is most likely if several screens
are attached. To recover, detach and reattach the DisplayLink screen.
(4061)
The log on screen may be offset or incorrectly sized, when DisplayLink
screens are attached. (4144)
After installing the DisplayLink software on a tablet PC, the pen
calibration software may not work correctly. Rebooting solves the
issue. (4448)
On some configurations with many DisplayLink screens, the screens may
take tens of seconds to display an image after connection, and to move
windows after disconnection. (4852)
Occasionally, Windows will recognise that a DisplayLink screens has
been disconnected after a long delay. (4852)
Occasionally, moving a video window onto an extended, rotated DL screen
results in corruption. To avoid this, don’t move the video window
around or change display settings while watching the video. (4697)
On ATI graphics, function key enabled display layout utilities may not
work correctly when the DisplayLink software is installed. (4964)
On some configurations, using more than 3 DisplayLink screens might
cause some DisplayLink screens to show corrupt or missing graphics.
Detaching and reattaching the screens should cure the problem.
(4747, 4835, 5159)
On a very small number of systems, a DisplayLink device might not work
correctly after having been quickly disconnected and reconnected.
A reboot is necessary to recover. To avoid the issue, wait a few
more seconds before reconnecting the device. (5471)
In certain circumstances, after unplugging a DisplayLink display there
can be a very long delay before the display is detached from the
Windows desktop. Rebooting greatly reduces the frequency of this issue
on the affected configurations (5137)
K3. Video players, rendering technologies and applications
----------------------------------------------------------
Video is supported on Windows Vista in WDDM (Aero) mode. Video playing
and rendering using hardware overlays is not supported. The following
players are tested by DisplayLink:
- Windows Media Player 11
(www.microsoft.com/windows/windowsmedia/default.mspx)
- WinDVD 8 (www.intervideo.com)
- PowerDVD 7 (www.cyberlink.com)
- RealPlayer 11 (www.real.com).
This table shows what rendering interfaces are supported:
Interface Supported on Vista WDDM Aero?
DxVA Yes, if supported by the GPU
D3D Yes, but not if the DisplayLink screen is primary
DirectDraw Yes
OpenGL Yes, but not full screen, windowed only
GDI+ Yes, but not full screen, windowed only
On Vista WDDM Basic, video is not supported. It may work in some
cases but exhibits poor performance. It may stop working after an
update from Windows Update that affects the graphics subsystem. (2028)
On all platforms, depending on the player, there may be problems if
the video window is moved between screens while video is running. It
may be necessary to close and restart the video player.
With Vista WDDM, on some lower-spec PCs, videos on DisplayLink attached
screens pause frequently for several seconds at a time. This is because
there is insufficient system performance to display video smoothly.
(1798)
Known Issues - General
Don't change the logged-on user or the display mode, position or
arrangement of attached screens while a video is running. This usually
confuses the video player and it may stop playing and/or show
corruption on screen. (1982, 4435, 5260)
On Vista WDDM, video players sometimes use hardware overlays to display
video. DisplayLink software does not support hardware overlays and
these videos do not display on DisplayLink screens. Examples: PowerDVD
7 uses overlays when playing DVDs and so cannot display DVDs on
DisplayLink screens. vlc can be configured to use overlays and will not
work on DisplayLink screens if so configured. (1807)
On Vista WDDM, some graphics-intensive applications use the GDI or
OpenGL interfaces. On DisplayLink attached screens, such applications
can display in a window but not full screen. Examples of such
applications are Starcraft, Quake 3. Also, video players such as
Windows Media Player, WinDVD fail to play in full screen mode on
DisplayLink screens on some PCs. (1655, 2134)
On Vista WDDM, applications such as games that use Direct3D will not
display on a DisplayLink attached screen that is set to primary. (1815)
Some players, including Windows Media Player, do not play DVD content
well on DisplayLink attached screens which are set as primary. (2084)
Full screen video might flicker on extending rotated DisplayLink
screens. The remedy is to avoid rotating the DisplayLink screen, or to
play video in a window. (4695)
On Vista in Basic mode, video will not play on DisplayLink screens after
installation until the PC is rebooted. In Aero mode no reboot is needed
before video will play. (4432)
Known issues with specific players and applications
On Vista WDDM, if Windows Media Player is moved to the DisplayLink
screen and is then made full-screen, the screen blanks. To get out of
this situation, either double click on the blank screen and the player
window is restored to non-full screen mode, or right click on the blank
screen to invoke the player context menu and select exit full screen.
(2032)
Skype video is believed to be unreliable with Vista. It may cause
crashes.
On Vista WDDM, if WinDVD is asked to play High-Definition content on a
DisplayLink screen, the content will not display and the player may
crash. This is because the player uses hardware overlays, which are not
supported by DisplayLink software. (1986)
On Vista WDDM, if PowerDVD 7 is playing video on a DisplayLink attached
screen, and if the screen is rotated, then PowerDVD 7 crashes. The
workaround is to apply rotation to the screen before launching PowerDVD
7. (2013)
On Vista 64-bit WDDM, dragging a WinDVD 9 playing video window between
screens may cause the video or the user interface to freeze.
To recover, detach and reattach the DisplayLink screen(s). (5258)
K4. Installer and Auto-update function
--------------------------------------
The installer and auto-update function work on all supported operating
systems, both hardware-first and software-first.
Known issues
Do not attach two new DisplayLink devices at once as software for one
of them may fail to install. Instead, fully install one device and see
it working before attaching a second device. (2022)
On Vista WDDM, the machine may drop to basic mode when a new
DisplayLink screen is connected. This is because of Vista's normal
performance calculation when new screens are attached. Aero mode can be
restored through Control Panel -> Windows Colour and Appearance -> Open
classic appearance properties for more colour options -> Windows Aero.
(2069)
If you attach a new DisplayLink device, allow software to start
installing, then cancel the install part way through, hardware-first
install may no longer work. To complete the install, it may be
necessary to run setup.exe directly. (1573)
Virus checkers set to very high security may prevent the installer
from running. They should be set to lower security during installation
and restored to high security once installation is complete. (935)
When installing, make sure that only a single user is logged into the
PC. That user needs administrator privileges. (1112)
On PCs where vbscript.dll is not registered with the DLLServer, the
DisplayLink installer cannot run. (1824)
AutoUpdate dialogs and menus are not yet localised in Hungarian,
Portuguese and Traditional Chinese. Other languages are complete.
When a previous usb display adapter driver for a DisplayLink device
is manually updated via device manager to this version a 'windows
encountered a problem installing the device' error may be shown during
the installation. This error can be safely ignored as the software
installation does not depend on it. (4663)
L. Summary of Software State and Issues - Vista XDDM, XP, 2K
============================================================
L1. Normal use
--------------
XDDM mode on Vista 64-bit is not supported. Please upgrade your
graphics card driver to the latest native Vista version available.
System behaviour with up to six DisplayLink attached screens has
been well tested. Testing covers plug/unplug, mode changes, playing
video, hibernate, sleep/standby, multiple users, different user rights,
attached screen as primary screen, attached screen as only screen,
and other aspects.
There are many annoyances and intermittent issues. General
recommendations when something goes wrong:
- try detaching then reattaching the DisplayLink device's USB cable
- try changing its display settings using the DisplayLink GUI or the
Windows Display Properties dialog box.
Known issues - hibernate / sleep / monitor power save / screensavers
On all OSes, the desktop background is occasionally missing after
restart or after resume from sleep or hibernation. The screens are
still usable, and the background can be set again to the desired
picture. (2154, 2072)
On all OSes, detaching or attaching DisplayLink attached screens while
a screensaver is running may cause strange effects. Sometimes it is
necessary to detach and reattach the DisplayLink attached screen after
exiting the screensaver. (1984)
3D screensavers do not run well on DisplayLink devices and can cause
flicker and/or decreased graphics performance. This is on all OSes.
(1150, 1177, 4426)
3D screensavers are not displayed on DisplayLink screens that are
rotated in portrait mode. (5076)
When the machine is set to ask for a password after standby / sleep /
hibernate / screensaver etc, sometimes the login screen displays on
all attached screens and sometimes it displays on a single screen only.
If devices are detached from the PC before going into standby, then
reattached during standby, very occasionally they may not resume when
the PC comes out of standby. If this happens, detach and reattach the
devices to make them work again. (1492)
Very occasionally, DisplayLink screens may fail to resume from
hibernation or standby. They come on after detach / reattach.
(4681, 4660)
Windows Foundation Presentation based applications may show corruption
or flashing on DisplayLink screens when opened. See
http://en.wikipedia.org/wiki/Windows_Presentation_Foundation for
details of WPF based applications. (4825, 4931)
There is an incompatibility on Windows XP between DisplayLink drivers
and older drivers for ASIX USB to Ethernet devices, which are included
in some USB docking stations. If you have problems in
connecting/disconnecting DisplayLink devices please make sure you have
installed version 3.4.3.29 or later of the ASIX drivers for your USB to
Ethernet devices. (5433)
On Windows XP and with multiple DisplayLink devices connected,
occasionally a DisplayLink screen might show corrupted or blank
contents after disconnecting and reconnecting. To recover, change
the resolution of the affected screen. (4880)
On a very small number of systems, a DisplayLink device might not work
correctly after having been quickly disconnected and reconnected.
A reboot is necessary to recover. To avoid the issue, wait a few
more seconds before reconnecting the device. (5471)
Known issues - Windows 2000
Installation of DisplayLink driver on Windows 2000 SP4 requires patch
SP4 Rollup 1. This is available from www.microsoft.com. See Microsoft
Knowledge Base article KB891861.
It is important to check in Windows 2000 that full USB2 is available,
otherwise performance will be impaired. To do this, look in Device
Manager under Universal Serial Bus Controllers for an item called
"USB 2.0 Root Hub". If it is not there then performance will be USB1.
(1188)
On Windows 2000, when many devices are attached to the PC and the PC
is hibernated then woken up, not all the devices come back to life
immediately. It is occasionally necessary to detach and reattach the
USB connection to a device to coax it back to life. (1293, 1302)
On a Windows 2000 system where only a DisplayLink screen is enabled,
locking the screen and then disconnecting it could cause all the other
screens to remain unusable. Reconnecting the DisplayLink screen solves
the issue. (4501)
Foreign language support on Windows 2000 has not been fully tested.
Layout information (enabled/extending/primary) for the main screen is
sometimes lost after reboot. The layout can be restored using the
Windows Display Properties dialog box. (4636)
Known issues - other
When fast user switching to an user account without administrative
privileges and then logging off, the DisplayLink screens may go black.
(4446)
In PowerPoint, the "Display slide show on:" menu has a bug which means
that it does not work when there are gaps in the numbering of enabled
displays (as shown in WDP). Users of PowerPoint 2007 can get round this
by using "Show presentation on:" in the ribbon, rather than the "Set
up slide show" box. (2337)
CRT monitors may show speckles at very high resolutions. This is
because the DisplayLink device cannot always support the high pixel
clock required with high CRT refresh rates. (2155)
The ATI Catalyst Control Center is a tool provided on machines with ATI
graphics cards for managing extra screens. Some versions of this tool
crash in the presence of DisplayLink software. This has been observed
with versions since ATI driver version 8.360. The workaround is to
uninstall the ATI Catalyst Control Center. (2054)
After a reboot, the numbers used in Windows Device Properties to
identify the attached screens may change. This is normal. (596)
On Windows XP, very occasionally, a 'The system cannot write to the
specified device' warning may be displayed after changing the display
mode several times (e.g. Extend/Dock mode) from the DisplayLink GUI.
If this happens, detach and reattach the devices to restore normal
operation. (4991)
L2. Video players, rendering technologies and applications
----------------------------------------------------------
On Vista XDDM, video support is very limited. With extended screens,
video or DVD playback are not supported in general. Exceptions:
PowerDVD7 and Quicktime are able to display video on a DisplayLink
attached display, so long as that display is the primary display. Video
is not supported in clone mode. It works, but exhibits poor
performance. (1495)
On XP, video support is limited to players that support hardware
overlays. In extend mode, the following media players work:
- Windows Media Player 11
(www.microsoft.com/windows/windowsmedia/default.mspx)
- WinDVD 8 (www.intervideo.com)
- PowerDVD 7 (www.cyberlink.com)
- RealPlayer 11 (www.real.com)
There is limited support for other video players, and for video in
mirror mode.
This table shows what rendering interfaces are supported:
Interface Supported on XP extend?
DxVA No
D3D No
DirectDraw Yes
OpenGL No
GDI+ No
On all platforms, depending on the player, there may be problems if
the video window is moved between screens while video is running. It
may be necessary to close and restart the video player.
Known issues - general
Don't change the logged user or the display mode, position or
arrangement of attached screens while a video is running. This usually
confuses the video player and the video may stop playing. (1982)
Some players, including Windows Media Player, do not play well on
DisplayLink attached screens which are set as primary. (2084)
DVD movies will not play back if they are dragged to an extended
DisplayLink screen while running. They play OK if the player
starts up on the extended screen. (no bug number)
On Windows 2000, video playing is not supported. (2708)
Known issues with specific players and applications
Windows Media Player sometimes fails to play DVDs on extended screens
on Windows XP. The workaround is to switch off VMR in WMP. (3884)
RealPlayer does not play DVDs on extended or mirrored screens on
Windows XP. This is the case whether the extra screens are
DisplayLink screens or directly attached. (2802)
Skype video is believed to be unreliable with Vista. It may cause
crashes (no bug number).
Skype video does not work on DisplayLink screens with Windows XP. This
is because Skype video uses VMR9, which is supported by DisplayLink
software on Vista WDDM, but not on Vista XDDM or on XP. Trying to use
Skype video on XP may cause black screens or freeze the DisplayLink
attached screen. (1651)
Blu-ray playback is not supported on DisplayLink screens. Players may
crash or behave erratically when trying to play Bluray content on a
DisplayLink screen. (3785, 5257)
When using a display in mirror mode, changing the rotation setting can
cause the display to go into extend mode. Setting the display back to
mirror mode will show the correct rotation. (2261)
Occasionally, on rotating a DisplayLink screen the monitor may freeze,
change resolution or go black. This is most likely if several screens
are attached. To recover, detach and reattach the DisplayLink screen.
(4061)
On Windows XP, DVD playback might not work correctly immediately after
having installed the DisplayLink software. Rebooting will solve the
issue. (5466)
L3. Installer and Auto-update function
--------------------------------------
The installer and auto-update function work on all supported operating
systems, both hardware-first and software-first. USB drivers have been
signed.
Known issues
On Windows 2000, DisplayLink software fails to install on PCs where
Service Pack 4 was installed before installing a MUI pack. This is a
Windows issue - see Microsoft Knowledge Base article 263212. To work
round this problem, go to Control panel, Regional Options, select the
General tab and change the Menus and Dialog combo box to English. You
will need to log off, and log back on. Install DisplayLink software,
and then set the language settings back to their original settings.
(1010)
Do not attach two new DisplayLink devices at once as software for one
of them may fail to install. Instead, fully install one device and see
it working before attaching a second device. (2022)
If you attach a new DisplayLink device, allow software to start
installing, then cancel the install part way through, hardware-first
install may no longer work. To complete the install, it may be
necessary to run setup.exe directly. (1573)
Virus checkers set to very high security may prevent the installer
from running. They should be set to lower security during installation
and restored to high security once installation is complete. (935)
When installing, make sure that only a single user is logged into the
PC. That user needs administrator privileges. (1112)
On PCs where vbscript.dll is not registered with the DLLServer, the
DisplayLink installer cannot run. (1824)
AutoUpdate dialogs and menus are not yet localised in Hungarian,
Portuguese and Traditional Chinese. Other languages are complete.
(Vista XDDM) Occasionally, after install and reboot, the DisplayLink
devices are not operational. In this case, reboot again and they
become operational. (969)
On Windows XP, very occasionally, the DisplayLink devices might not
work after installing the DisplayLink drivers using the 'Update driver'
function in Device Manager or using Windows Update. Rebooting solves
the issue. (5369)
M. Driver qualification information
-----------------------------------
The following DisplayLink driver components included in this release
have been qualified and signed by Microsoft's Windows Quality Labs
(WHQL) with the specified submission identification number:
ID 1327230 - usb-v5.0.18191.0
ID 1319651 - mirror-v5.0.16859
ID 1319878 - extend-v5.0.16961
ID 1321659 - filter-5.0.17276.0
ID 1338874 - dlkmd-v5.1.19941.0
ID 1327227 - dlkmdldr-v5.0.18123.0
ID 1327231 - composite-v5.0.18212.0
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.