/** \file * * This file contains special DoxyGen information for the generation of the main page and other special * documentation pages. It is not a project source file. */ /** \mainpage Denver Gingerich's USBSnoop Magnetic Card Reader Project * * \section SSec_Compat Project Compatibility: * * The following list indicates what microcontrollers are compatible with this project. * * - AT90USB1287 * - AT90USB1286 * * \section SSec_Info USB Information: * * The following table gives a rundown of the USB utilization of this project. * * <table> * <tr> * <td><b>USB Mode:</b></td> * <td>Device</td> * </tr> * <tr> * <td><b>USB Class:</b></td> * <td>Human Interface Device (HID)</td> * </tr> * <tr> * <td><b>USB Subclass:</b></td> * <td>Keyboard</td> * </tr> * <tr> * <td><b>Relevant Standards:</b></td> * <td>USBIF HID Standard, USBIF HID Usage Tables</td> * </tr> * <tr> * <td><b>Usable Speeds:</b></td> * <td>Full Speed Mode</td> * </tr> * </table> * * \section SSec_Description Project Description: * * Firmware for a USB AVR powered USB TTL magnetic stripe reader (using a card * reader such as the Omron V3B-4K) by Denver Gingerich. This project is designed * to be used with the open source Stripe Snoop project at <a>http://stripesnoop.sourceforge.net/</a>. * * See <a>http://ossguy.com/ss_usb/</a> for the USB reader hardware project website, * including construction and support details. * * To use, connect your magnetic card reader device to the USB AVR as follows (pin and port mapping may be adjusted * from the project makefile): * * <table> * <tr> * <td><b>Signal:</b></td> * <td><b>AVR Port:</b></td> * </tr> * <tr> * <td>Track 1 Data</td> * <td>PORTC, Pin 1</td> * </tr> * <tr> * <td>Track 1 Clock</td> * <td>PORTC, Pin 2</td> * </tr> * <tr> * <td>Track 2 Data</td> * <td>PORTC, Pin 3</td> * </tr> * <tr> * <td>Track 2 Clock</td> * <td>PORTC, Pin 0</td> * </tr> * <tr> * <td>Track 3 Data</td> * <td>PORTC, Pin 5</td> * </tr> * <tr> * <td>Track 3 Clock</td> * <td>PORTC, Pin 6</td> * </tr> * <tr> * <td>Card Detect</td> * <td>PORTC, Pin 4</td> * </tr> * </table> * * This project is based on the LUFA Keyboard projectnstration application, * written by Denver Gingerich. * * This application uses a keyboard HID driver to communicate the data collected * a TTL magnetic stripe reader to the connected computer. The raw bitstream * obtained from the magnetic stripe reader is "typed" through the keyboard * driver as 0's and 1's. After every card swipe, the project will send a return key. * * \section SSec_Options Project Options * * The following defines can be found in this project, which can control the project behaviour when defined, or changed in value. * * <table> * <tr> * <td><b>Define Name:</b></td> * <td><b>Location:</b></td> * <td><b>Description:</b></td> * </tr> * <tr> * <td>MAX_BITS</td> * <td>CircularBitBuffer.h</td> * <td>Gives the maximum number of bits per track which can be buffered by the device for later transmission to a host.</td> * </tr> * <tr> * <td>MAG_T1_CLOCK</td> * <td>Makefile LUFA_OPTS</td> * <td>Mask for the magnetic card reader's CLOCK line for the reader's track 1 output.</td> * </tr> * <tr> * <td>MAG_T1_DATA</td> * <td>Makefile LUFA_OPTS</td> * <td>Mask for the magnetic card reader's DATA line for the reader's track 1 output.</td> * </tr> * <tr> * <td>MAG_T2_CLOCK</td> * <td>Makefile LUFA_OPTS</td> * <td>Mask for the magnetic card reader's CLOCK line for the reader's track 2 output.</td> * </tr> * <tr> * <td>MAG_T2_DATA</td> * <td>Makefile LUFA_OPTS</td> * <td>Mask for the magnetic card reader's DATA line for the reader's track 2 output.</td> * </tr> * <tr> * <td>MAG_T3_CLOCK</td> * <td>Makefile LUFA_OPTS</td> * <td>Mask for the magnetic card reader's CLOCK line for the reader's track 3 output.</td> * </tr> * <tr> * <td>MAG_T3_DATA</td> * <td>Makefile LUFA_OPTS</td> * <td>Mask for the magnetic card reader's DATA line for the reader's track 3 output.</td> * </tr> * <tr> * <td>MAG_CARDPRESENT</td> * <td>Makefile LUFA_OPTS</td> * <td>Mask for the magnetic card reader's card detection output.</td> * </tr> * <tr> * <td>MAG_PIN</td> * <td>Makefile LUFA_OPTS</td> * <td>PIN register that the magnetic card reader device is attached to.</td> * </tr> * <tr> * <td>MAG_PORT</td> * <td>Makefile LUFA_OPTS</td> * <td>PORT register that the magnetic card reader device is attached to.</td> * </tr> * <tr> * <td>MAG_DDR</td> * <td>Makefile LUFA_OPTS</td> * <td>DDR register that the magnetic card reader device is attached to.</td> * </tr> * </table> */Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.