1. 9523652.exe Driver
2. readme.txt File Contents

readme.txt Driver File Contents (9523652.exe)

Information and Instructions about this download file

=======================
File Description: Gateway(r) CardBus Controller Driver
Version: 5.00.2195.3005
Operating System: Microsoft(r) Windows(r) XP, Windows 2000
Part Number: 9523652
Date: 10/24/2001
=======================

Table of Contents
=======================
Overview
Identification
Installation
Removal
Troubleshooting
Reason for Update
=======================


Overview

This document describes the steps necessary to install and configure the Windows XP or Windows 2000 CardBus Controller driver for the Gateway notebook computers listed in the Applicable Part Numbers section below.


Identification

If you have a Gateway notebook computer listed below and are running Windows XP or Windows 2000, install these drivers.


Installation

After you have downloaded and double-clicked the file (9523652.exe), files are self-extracted and copied into the C:\Cabs\9523652 folder on the hard drive.

Windows XP

1.  From the Start menu, click Control Panel.  

2.  In Control Panel, click Performance and Maintenance, and then double-click the System icon.  

3.  In the System Properties dialog box, click the Hardware tab.  On the Hardware tab, click Device Manager.

4.  In Device Manager, under PCMCIA adapters, double-click Texas Instruments PCI-4510 CardBus Controller.  If the driver has never been installed, it is listed as PCI to CARDBUS Bridge under Other Devices.

5.  In the Texas Instruments PCI-4510 CardBus Controller Properties dialog box or in the PCI to CARDBUS Bridge Properties dialog box, click the Driver tab, and then click Update driver.

6.  In the Hardware Update Wizard dialog box, select Install from a list or Specific Location (Advanced), and then click Next

7.  In the Hardware Update Wizard dialog box, select Don't search I will choose the driver to install, and then click Next.

8.  In the next dialog box, click Have Disk.

9.  In the Install From Disk dialog box, type: C:\Cabs\9523652.  Click OK.

10. Windows detects and installs the Texas Instruments PCI-4510 CardBus Controller.

11.  In the Completing the Upgrade Device Driver Wizard dialog box, click Finish. 

12.  In the Texas Instruments PCI-4510 CardBus Controller Properties dialog box, click Close.


Windows 2000

1.  From the Start menu, point to Settings, and then click Control Panel.  

2.  In Control Panel, double-click the System icon.  

3.  In the System Properties dialog box, click the Hardware tab.  On the Hardware tab, click Device Manager.

4.  In Device Manager, under PCMCIA adapters, double-click Texas Instruments PCI-4510 CardBus Controller.  If the driver has never been installed, it is listed as PCI to CARDBUS Bridge under Other Devices.

5.  In the Texas Instruments PCI-4510 CardBus Controller Properties dialog box or in the PCI to CARDBUS Bridge Properties dialog box, click the Driver tab, and then click Update driver..

6.  In the Update Device Driver Wizard dialog box, click Next.

7.  In the Install Hardware Device Drivers dialog box, select Search for a suitable driver for my device (recommended), and then click Next.

8.  In the Locate Driver Files dialog box, verify that only Specify a Location is selected, and then click Next.

9.  In the Upgrade Device Driver Wizard dialog box, type: C:\Cabs\9523652.  Click OK.

10. Windows detects and installs the Texas Instruments PCI-4510 CardBus Controller.

11.  In the Completing the Upgrade Device Driver Wizard dialog box, click Finish. 

12.  In the Texas Instruments PCI-4510 CardBus Controller Properties dialog box, click Close.


Removal

Windows XP

1.  From the Start menu, click Control Panel.  

2.  In Control Panel, click Performance and Maintenance, and then double-click the System icon.  

3.  In the System Properties dialog box, click the Hardware tab.  On the Hardware tab, click Device Manager.

4.  In Device Manager, under PCMCIA adapters, double-click Texas Instruments PCI-4510 CardBus Controller.  

5.  In the Texas Instruments PCI-4510 CardBus Controller Properties dialog box, click the Driver tab, and then click Uninstall.

6.  In the Confirm Device Removal dialog box, click OK.


Windows 2000

1.  From the Start menu, point to settings, and then click Control Panel.  

2.  In Control Panel, double-click the System icon.  

3.  In the System Properties dialog box, click the Hardware tab.  On the Hardware tab, click Device Manager.

4.  In Device Manager, under PCMCIA adapters, double-click Texas Instruments PCI-4510 CardBus Controller.  

5.  In the Texas Instruments PCI-4510 CardBus Controller Properties dialog box, click the Driver tab, and then click Uninstall.

6.  In the Confirm Device Removal dialog box, click OK.


Troubleshooting

If you are having difficulty during or after the driver installation, follow the removal procedure, and then re-install the drivers.


Reason for Update

This is the initial driver release.


Applicable Part Numbers

Gateway M350WVN:  3501666, 3501668, 3501673, 3501675, 3501677, 3501678, 3501802, 3501803, 3501804, 3501805, 3501863