ACU.ini Driver File Contents (atheros_wpa_client.exe)

//.............................................................................
//
//  Copyright © 2001 Atheros Communications, Inc.,  All Rights Reserved.
//
//  The entries in this file describe a profile.  Entries are in Name/Value pairs separated by white spece
//  comments are allowed as long as you use the following syntax:
//                     Name   Value    //comment
//
//  The variable names are not case sensitive.  If multiple entries for the same variable are present, then the
//  last valid one parsed is used.
//  
//  To modify a default settings for a new profile, uncomment the variables you wish to change
//  and set the second field to the desired value.
//
//.............................................................................
//
//
//  ProfileName                         New                     //Sets the profile name		
//  NetworkName                         Name1                   //Sets the first network name
//  NetworkName2                        Name2                   //Sets the second network name
//  NetworkName3                        Name3                   //Sets the third network name
//  NetworkType                         1                       //Ad Hoc = 0, Infrastructure = 1
//  PowerManagement                     0                       //Off = 0, Max = 1, Normal = 2			
//
//	Security modes are as follows:
//	   LEAPEnabled and ExternallyManagedSecurity are mutually exclusive
//	   LEAPEnabled or ExternallyManagedSecurity overrides SecurityEnabled
//	   If LEAPEnabled and ExternallyManagedSecurity is 0 but SecurityEnabled is 1, then Pre-Shared Keys
//	   If all 0, then security is disabled
//
//  SecurityEnabled                     1                        //1 = Enabled, 0 = Disabled (no security)	
//  ExternallyManagedSecurity           0                        //1 = Externally Managed, 0 = Not Externally Managed
//  LEAPEnabled                         0                        //1 = Leap Enabled, 0 = Leap Not Enabled
//
//	Encryption Keys	
//
//  HexKeyEntry                         1                        //1 = Key entry is in Hex, 0 = Key entry in ASCII		
//  DefaultKey                          0                        //which key (0 - 4) is the default
//  Key1                                0                        //Key Value
//  Key2                                0                        //Key Value
//  Key3                                0                        //Key Value
//  Key4                                0                        //Key Value
//  UniqueKey                           0                        //Key Value
//  UserName                            0                        //UserName for LEAP
//  Password                            0                        //Password for LEAP
//  Key1Length                          40                       //Key Length
//  Key2Length                          40                       //Key Length
//  Key3Length                          40                       //Key Length
//  Key4Length                          40                       //Key Length
//  UniqueKeyLength                     40                       //Key Length
//  PasswordLength                      40                       //Key Length
//
//	Advanced	
//
//  ScanType                            0                       //Passive = 0, Auto = 1
//  Preamble                            0                       //1 = allow short & long; 0 long only
//  TransmitPower                       0                       //Full = 0, Half = 1, Quarter = 2, Eighth = 3, Min = 4
//
//
//	Network and Ad Hoc bands - value will be anded against valid bands for device
//	5 GHz 54 Mbps = 1, 5 GHz 108 Mbps = 2, 2.4 GHz 11 Mbps = 4, 2.4 GHz 54 Mbps = 8			
//
//  NetworkBand                          15
//  AdHocBand                            15
//  
//  Channel                              0                       //Ad Hoc channel for b or g (0 = auto; 1-11)
Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web3, load: 1.49