1. fpmmc_w2k_rc2_eng.exe Driver
2. Readme.txt File Contents

Readme.txt Driver File Contents (fpmmc_w2k_rc2_eng.exe)

README.TXT
FlashPath for MultiMediaCard, by SmartDisk Corporation

NOTES FOR:

* "FLASHPATH FOR MULTIMEDIACARD" FOR SUPPORT OF:
   IBM PC/AT COMPATIBLE PCs (SINGLE INTEL x86, PENTIUM 
   133 MHZ CPU OR HIGHER, OR FULLY COMPATIBLE CPU) RUNNING 
   - MICROSOFT WINDOWS 2000.


  * All documentation and programs Copyright 1999-2000, SmartDisk
    Corporation.

  * FlashPath is a registered trademark of SmartDisk Corporation.

  * MultiMediaCard is a registered trademark of Infineon.

  * Windows 2000 is a registered trademark of Microsoft Corporation.

  * All other brand and product names are registered trademarks
    of their respective owners.

      *******************************************************
     *                  TABLE OF CONTENTS                    * 
     *                                                       *
     * 1. SOFTWARE REVISION HISTORY                          *
     * 2. GETTING READY                                      *
     * 3. IMPORTANT NOTES (CAUTION)                          *
     * 4. NOTES                                              *
     *                                                       *
      *******************************************************
	
	               
1. ===[SOFTWARE REVISION HISTORY]===

   
   Rev.     	Date and Comments
   ---------    -----------------------------------------------------
   1.50.19	July 31, 2000
   RC2
           	Release Candidate 2 version of "FlashPath for MultiMediaCard",
		for Windows 2000.

	        You must uninstall any prior version of "FlashPath
		for MultiMediaCard", BEFORE installing this version.

		Supports IBM PC/AT compatible PCs (with a single Intel 
		x86, Pentium 133 MHz or higher, or fully compatible CPU)
		running:

		* Windows 2000
		  English, Japanese, French, Spanish, and German.


		PLEASE ALSO NOTE THAT WHEN YOU INSTALL "FLASHPATH FOR 
		MULTIMEDIACARD" ON THE ABOVE LANGUAGE VERSIONS OF THE 
		OPERATINGS SYSTEMS, THAT THE "FLASHPATH FOR MULTIMEDIACARD" 
		- 'USER INTERFACE' AND ALL MESSAGES ARE IN THE ENGLISH LANGUAGE.


2. ===[GETTING READY]===
   Please read the following information before installing
   FlashPath for MultiMediaCard.

   A. INSTALLATION

      You must uninstall any prior version of "FlashPath
      MultiMediaCard", BEFORE installing this version.

      This version does not install a "FlashPath MultiMediaCard
      Format" program, or help files.


   B. SYSTEM REQUIREMENTS

       1. HARDWARE:

          Requires:

	  a.  An IBM PC/AT compatible PC with a single Intel 
	      x86 (Pentium 133 MHz or higher) or fully compatible CPU.
		1. Does NOT work on multiple CPU systems.
  		2. Does NOT work on RISC based systems
		   (Alpha AXP, MIPS R4x00, or PowerPCs).

	   b. At least a single 3.5 inch floppy disk drive:
                3.5 inch, 1.44MB floppy disk drive, or a
                3.5 inch Japanese 3-mode floppy disk drive.
             
	      DOES NOT SUPPORT:
		- LS-120 SuperDrives (120MB / 1.44MB).
		- External floppy drives (USB, serial, 
		  parallel or other external interface).


       2. OPERATING SYSTEMS:

            a. Microsoft Windows 2000

		NOTE:
		In order to install or uninstall FlashPath software
		on Windows 2000, you must be a user with 
		"Administrator Privileges".


            b. DOES NOT INSTALL ON:
		1. Microsoft Millennium
		2. Microsoft Windows 98
		3. Microsoft Windows 95
		4. Microsoft Windows NT 4.0
		5. Windows NT 3.51
		6. Windows 3.x or MS-DOS.



3. ===[IMPORTANT NOTES (CAUTION)]===

      Incompatible Floppy Disk Drives (FDDs) with which FlashPath 
      cannot be used.

      The FlashPath cannot be used with a FDD which is connected 
      via a different interface from ordinary FDDs. 

      Unsupported FDDs include the following:

      1. An external FDD connected via a PC card (PCMCIA), or 
         USB/ serial/ parallel ports.

      2. A high recording capacity FDD such as a Imation SuperDisk
         (LS-120) 120MB/ 1.44MB floppy disk drive (they connect to 
         the PC through an IDE cable or parallel (printer) port, 
         rather than the standard floppy drive port).

      3. If you access the FlashPath when the "FlashPath Status
         Monitor" program is not activated (i.e. while its icon
         is not shown on the task bar) and then activate the
         program later, the display will not immediately reflect
         the current internal status of the FlashPath.

         This is because the "FlashPath Status Monitor" program
         starts operating the moment it detects the first access
         made after the FlashPath has been inserted in the FDD.
         Therefore, in order to make sure that the "FlashPath
         Status Monitor" reflects the internal status of the
         FlashPath, eject the FlashPath from the FDD, and then
         insert it again.
         

4. ===[NOTES]===

   A. The copyright of this README.TXT file, the manual and the 
      software is owned by SmartDisk Corporation.

   B. This software and manual may not be reproduced in whole or 
      in part. Duplication of the software for any purpose other
      than backup is prohibited.

   C. Analysis, reverse engineering, disassembly, coupling with 
      another application, incorporation or printing of the main 
      application, DLLs and other files in this software is
      prohibited.

   D. SmartDisk Corporation assumes no liability for any loss or 
      damages relating to the operation of this software or to 
      information provided in the manual, or this README.TXT
      file.

   E. To accommodate technical improvements, the contents of the 
      software and manual may be subject to change without prior
      notice.

   F. SmartDisk Corporation has taken every reasonable effort to
      ensure that its products meet the highest standards of
      quality and reliability.  Please do not hesitate to contact
      us if you find any problems, mistakes or disk defects.