OEMSETNT.INF Driver File Contents (dmf560tx.exe)

;***********************************************************************
;
;       Network card and driver SETUP INF file.
;
;       OEMSETNET.INF
;
;***********************************************************************


[Identification]
    OptionType = NetAdapter


[PlatformsSupported]
    ISA
    EISA
    "Jazz-Internal Bus"
;;+ Andge
    PCMCIA
;;-


[Options]
    LMNDIS

;***********************************************************************
; CONSTANTS FOR USING DIALOGS
;***********************************************************************

[FileConstants]


GenericInfVersion   = "v1.0"
GenericAdapterName  = "D-Link DMF-560TXD DirectPort PC Card"
GenericDriverName   = "D-Link DMF-560TXD DirectPort PC Card Driver"
GenericFunctionName = "D-Link DMF-560TXD DirectPort PC Card"
GenericSysName      = "LMNDIS3.SYS"
GenericName         = "LMNDIS"



;
;  File names, etc.
;
UtilityInf      = "UTILITY.INF"
ParamInf        = "NCPARAM.INF"
subroutineinf   = "SUBROUTN.INF"
SoftwareType    = "driver"
Exit_Code       = 0

NetEventDLL     = "%SystemRoot%\System32\netevent.dll"
IoLogMsgDLL     = "%SystemRoot%\System32\IoLogMsg.dll"

Manufacturer    = "Microsoft"
ProductMajorVersion     = "3"
ProductMinorVersion     = "1"
ProductVersion  = $(ProductMajorVersion)"."$(ProductMinorVersion)

ProductSoftwareName     = "LMNDIS"
ProductSoftwareImagePath = "\SystemRoot\System32\drivers\"$(GenericSysName)
NetRuleSoftwareType     = "LMNDISSys ndisDriver LMNDISDriver"

NetRuleSoftwareUse      = $(SoftwareType)
NetRuleSoftwareBindForm = """LMNDISSys"" yes no container"

NetRuleSoftwareClass    = {"LMNDISDriver basic"}
NetRuleSoftwareBindable = {"LMNDISDriver LMNDISAdapter non exclusive 100"}

ProductHardwareName        = "LMNDIS"
NetRuleHardwareType        = "LMNDIS LMNDISAdapter"
NetRuleHardwareBindForm    = " yes yes container"
NetRuleHardwareClass       = {"LMNDISAdapter basic"}



ProductKeyName  = $(!NTN_SoftwareBase)"\"$(Manufacturer)"\"$(ProductSoftwareName)"\CurrentVersion"
ParamKeyName    = $(!NTN_ServiceBase)"\"$(ProductHardwareName)"\Parameters"
;;+ 1-12-1996 Andge
PCCardDataBase = $(!NTN_ServiceBase)"\Pcmcia\DataBase"
NICDataBase = $(PCCardDataBase)"\D-Link\DMF-560TXD DirectPort PC Card"
;;-
;+ For CardWizard 1-16-98
CardwizDataBase = $(!NTN_ServiceBase)"\resman\MacDataBase"
CWZNICDataBase = $(CardwizDataBase)"\D-Link\DMF-560TXD DirectPort PC Card"
;- For CardWizard 1-16-98


[GeneralConstants]
from      = ""
to        = ""

ExitCodeOk     = 0
ExitCodeCancel = 1
ExitCodeFatal  = 2

KeyNull         = ""
MAXIMUM_ALLOWED   = 33554432
RegistryErrorIndex = NO_ERROR
KeyProduct      = ""
KeyParameters   = ""
;;+ 1-12-1996 Andge
KeyPCCard       = ""
KeyDataBase     = ""
;;-
NT400VersionConstant = "(4.0)"

TRUE            = 1
FALSE           = 0
NoTitle         = 0

ExitState   = "Active"
OldVersionExisted = $(FALSE)

DriverPath      = $(!STF_NTPATH)\drivers

[date]
    ; Now is a list which contains { Sec from 1-1-1970, Year, Month, Day, Hour,
    ; Minute, Second }
    Now = {} ? $(!LIBHANDLE) GetSystemDate



[Identify]
    ;
    ;
    read-syms Identification


    set Status     = STATUS_SUCCESSFUL
    set Identifier = $(OptionType)
    set Media      = #("Source Media Descriptions", 1, 1)

    set STF_DISPLAYDEBUGOUTPUT  =   1   ; +++ 10/24/95 tammie

    Return $(Status) $(Identifier) $(Media) $(STF_DISPLAYDEBUGOUTPUT)


[ReturnOptions]
    ;
    ;
    set Status        = STATUS_FAILED
    set OptionList     = {}
    set OptionTextList = {}

    ;
    ; Check if the language requested is supported
    ;
    set LanguageList = ^(LanguagesSupported, 1)
    Ifcontains(i) $($0) in $(LanguageList)
        ;
        ; Check if the platforms requested is supported
        ;
        ifstr(i) $($1) == ""
                        goto returnoptions
        endif

        set PlatformList = ^(PlatformsSupported, 1)
        Ifcontains(i) $($1) in $(PlatformList)
                        goto returnoptions
        else
                        set Status = STATUS_NOTSUPPORTED
                        goto finish_ReturnOptions
        endif
    else
                set Status = STATUS_NOLANGUAGE
                goto finish_ReturnOptions
    endif

    ;
    ; form a list of all the options and another of the text representing
    ;

returnoptions = +
    set OptionList     = ^(Options, 1)
    set OptionTextList = ^(OptionsText$($0), 1)
    set Status         = STATUS_SUCCESSFUL

finish_ReturnOptions = +
    Return $(Status) $(OptionList) $(OptionTextList)

[InstallOption]
    ;
    ; Set default values for
    ;
    set Status   = STATUS_FAILED
    ;
    ; extract parameters
    ;
    set Option   = $($1)
    set SrcDir   = $($2)
    set AddCopy  = $($3)
    set DoCopy   = $($4)
    set DoConfig = $($5)

    ;
    ; Check if the language requested is supported
    ;
    set LanguageList = ^(LanguagesSupported, 1)
    Ifcontains(i) $($0) NOT-IN $(LanguageList)
        Return STATUS_NOLANGUAGE
    endif

    set-subst LF = "\n"

    read-syms GeneralConstants
    read-syms FileConstants

    read-syms DialogConstants$(!STF_LANGUAGE)
    ifstr(i) $(!NTN_Origination) == "NCPA"
        set Continue = $(OK)
    endif
    read-syms FileConstants$(!STF_LANGUAGE)

    detect date

    set-title  $(FunctionTitle)

    set to   = Begin
    set from = Begin
;
;  Assume all is well.
;
    set CommonStatus = STATUS_SUCCESSFUL

    EndWait

;
;   Set up the operation-mode-based variables and gaily welcome
;   the user.  If the "install mode" variable is improperly set,
;   assume this is a new installation.
;

Begin = +
;;;;; detement OS
    set CurrentVersionValue = ""
    OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows Nt\CurrentVersion" $(!REG_KEY_READ) KeyNt

    Ifstr(i) $(KeyNt) != ""
        GetRegValue $(KeyNt) "CurrentVersion" CurrentVersionValue
        CloseRegKey $(KeyNt)
    Endif

    ifstr(i) (*($(CurrentVersionValue),4)) == $(NT400VersionConstant)
        set NT_VER = NT4
        OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Enum\Root\LEGACY_PCMCIA\0000" $(!REG_KEY_READ) KeyPCMCIA
        Ifstr(i) $(KeyPCMCIA) != ""
           GetRegValue $(KeyPCMCIA) "StatusFlags" PCMCIAFlag
           CloseRegKey $(KeyPCMCIA)
           set PCMCIAStatusFlag = *($(PCMCIAFlag), 4)
        Endif
    else
        set NT_VER = NT3
    endif
;;;;
    Set ActivateDetection = FALSE

    Ifstr(i) $(!NTN_InstallMode) == deinstall
        set StartLabel = removeadapter
    else-Ifstr(i) $(!NTN_InstallMode) == Update
        set StartLabel = UpgradeSoftware
    else-Ifstr(i) $(!NTN_InstallMode) == bind
        set StartLabel = bindingadapter
    else-Ifstr(i) $(!NTN_InstallMode) == configure
;        set ActivateDetection = TRUE
        set StartLabel = configureadapter
        ;
        ;   You cannot config the software component
        ;
        Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase)
            Debug-Output "Cannot configure the driver software."
            Shell $(UtilityInf),RegistryErrorString,CANNOT_CONFIGURE_SOFTWARE
            ifint $($ShellCode) != $(!SHELL_CODE_OK)
                Debug-Output "ShellCode error: cannot get an error string."
                goto ShellCodeError
            endif
            set Error = $($R0)
            set from = end
            set to = end
            goto nonfatalinfo
        endif
    else
;        set ActivateDetection = TRUE
        set StartLabel = installadapter
        set OEM_ABANDON_OPTIONS = {}
        set OEM_ABANDON_SOFTWARE = FALSE
        set OEM_ABANDON_ON = TRUE
    endif


    ;  set the default values

    ; IRQ Level = 11
    set IRQValue = *($(IRQList), 7)

    ; IOBase Address = 0x320
    set IOBaseAddrValue = *($(IOBaseAddrList), 2)

;Kenny
    ;* IoBase Address for Modem *
    set ModemIOBaseAddressValue = *($(ModemIOBaseAddressList), 3)       ; IOBase Address = 0x2F8


    ; Memory Address = 0xd0000
    set MemAddrValue = *($(MemAddrList), 1)

    ; Connection Type = Auto_Sense
    set ConnectionValue = *($(ConnectionList), 1)

    ; COM Port = 3
    set ComPortValue = *($(ComPortList), 2)

    ; COM IRQ = 5
    set ComIrqValue = *($(ComIrqList), 4)

    ;DirectEnable ;zachary
    set DirectEnableValue           = "OFF"                             ; Direct Enable = off
    set PcmciaValue                 = "ON"             ; Pcmcia Enabler = 1

    Set from = $(fatal)
    Set to = $(fatal)
    Goto $(StartLabel)

;-----------------------------------------------
; Installation Section
;-----------------------------------------------

installadapter = +
;
;   First, check whether the same version of the software exists
;
    OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct

    Ifstr $(KeyProduct) != $(KeyNull)
        ;
        ; Same version already existed in the local machine
        ; Popup the dialog and ask the user whether he wants to continue
        ;
        CloseRegKey $(KeyProduct)

        ifstr(i) !(NTN_RegBase) == $(ProductKeyName)
           ;
           ; Cannot Install the same software again
           ;
           Shell $(UtilityInf), VerExistedDlg, $(ProductSoftwareTitle),+
               $(ProductVersion)
           ifint $($ShellCode) != $(!SHELL_CODE_OK)
               Debug-Output "ShellCode error: cannot get an error string."
               goto ShellCodeError
           endif

           goto end
        else
           ;
           ; Add a new adapter card?
           ;
           Shell $(UtilityInf), CardExistedDlg

           ifint $($ShellCode) != $(!SHELL_CODE_OK)
               Debug-Output "ShellCode error: cannot get an error string."
               goto ShellCodeError
           endif

           ifstr(i) $($R1) != "OK"
               goto end
           endif
           set OldVersionExisted = $(TRUE)
        endif
    endif

;
;  dll load addition
;
    Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) YES

    Ifint $($ShellCode) != $(!SHELL_CODE_OK)
        Goto ShellCodeError
    Else-Ifstr(i) $($R0) == STATUS_FAILED
        Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL"
        ifint $($ShellCode) != $(!SHELL_CODE_OK)
            goto ShellCodeError
        endif
        set Error = $($R0)
        Goto fatal
    Else-Ifstr(i) $($R0) == STATUS_USERCANCEL
        Goto successful
    Endif

;   Set SrcDir = $($R1)WINNT\
    Set SrcDir = $($R1)

    install "Install-Dll"

    goto adaptersetup

;-----------------------------------------------
; Configuration Section
;-----------------------------------------------
;
;   Get the current values of all the parameters
;
configureadapter = +
    Ifstr $(KeyProduct) == $(KeyNull)
        OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) $(MAXIMUM_ALLOWED) KeyProduct
        Ifstr $(KeyProduct) == $(KeyNull)
            set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE
            Debug-Output "Cannot find component product key"
            goto fatalregistry
        Endif
    Endif

    ;
    ; Get the other parameters;  they're attached to the service parameters key
    ;
    Debug-Output "INF: Shelling to FindService"
    Shell $(UtilityInf) FindService, $(KeyProduct)
    Ifint $($ShellCode) != $(!SHELL_CODE_OK)
        Debug-Output "INF: FindService shell failure"
        Goto ShellCodeError
    Endif
    Ifstr(i) $($R0) != NO_ERROR
        Debug-Output "INF: FindService Shell error: "$($R0)
        Goto fatalregistry
    endif

    Set KeyParameters = $($R2)

    ;
    ;  We don't need the services key, so close it.
    ;
    CloseRegKey $($R1)

    Ifstr $(KeyParameters) == $(KeyNull)
        set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE
        Debug-Output "Cannot find component service"
        goto fatalregistry
    endif

    set OldVersionExisted = $(TRUE)

    set ValueName = ""
    set ValueData = ""
    set ValueStr  = ""
    set ValueList = {}


    ;
    ; Get the old values
    ;
    EnumRegValue $(KeyParameters) ValueList

    Debug-Output $(InfName)" KeyParameters is "$(KeyParameters)

    ifstr(i) $(NT_VER) == NT4
     ifint $(PCMCIAStatusFlag) == 8
          ForListDo $(ValueList)
              set ValueItem = $($)
              set ValueName = *($(ValueItem),1)
              set ValueData = *($(ValueItem),4)

              ifstr(i) $(ValueName) == "IoBaseAddress_1"
                  set IOBaseAddrIndex = $(ValueData)
              else-ifstr(i) $(ValueName) == "IOBaseAddress"
                      set ModemIOBaseAddressIndex = $(ValueData)
              else-ifstr(i) $(ValueName) == "InterruptNumber"
                  set IRQValueIndex = $(ValueData)
              else-ifstr(i) $(ValueName) == "PCCARDAttributeMemoryAddress"
                  set MemAddrIndex = $(ValueData)
              else-ifstr(i) $(ValueName) == "ComPort"
                  set ComPortValueIndex = $(ValueData)
              else-ifstr(i) $(ValueName) == "ConnectionType"
                  set ConnectionIndex = $(ValueData)
              else-ifstr(i) $(ValueName) == "DirectEnable"  ;zachary
                  set DirectEnableValue = $(ValueData)
              endif
          EndForListDo
     else
       ForListDo $(ValueList)
            set ValueItem = $($)
            set ValueName = *($(ValueItem),1)
            set ValueData = *($(ValueItem),4)
            ifstr(i) $(ValueName) == "IoBaseAddress_1"
                set IOBaseAddrIndex = $(ValueData)
            else-ifstr(i) $(ValueName) == "IOBaseAddress"
                set ModemIOBaseAddressIndex = $(ValueData)
            else-ifstr(i) $(ValueName) == "InterruptNumber"
                set IRQValueIndex = $(ValueData)
            else-ifstr(i) $(ValueName) == "PCCARDAttributeMemoryAddress"
                set MemAddrIndex = $(ValueData)
            else-ifstr(i) $(ValueName) == "ComPort"
                set ComPortValueIndex = $(ValueData)
            else-ifstr(i) $(ValueName) == "ConnectionType"
                set ConnectionIndex = $(ValueData)
            else-ifstr(i) $(ValueName) == "DirectEnable"      ;zachary
                set DirectEnableValue = $(ValueData)
            else-ifstr(i) $(ValueName) == "ComIRQ"
                set ComIrqValueIndex = $(ValueData)
            endif
       EndForListDo
     endif
    else            ; for NT 3.51
       ForListDo $(ValueList)
            set ValueItem = $($)
            set ValueName = *($(ValueItem),1)
            set ValueData = *($(ValueItem),4)
            ifstr(i) $(ValueName) == "IoBaseAddress_1"
                set IOBaseAddrIndex = $(ValueData)
            else-ifstr(i) $(ValueName) == "IOBaseAddress"
                set ModemIOBaseAddressIndex = $(ValueData)
            else-ifstr(i) $(ValueName) == "InterruptNumber"
                set IRQValueIndex = $(ValueData)
            else-ifstr(i) $(ValueName) == "PCCARDAttributeMemoryAddress"
                set MemAddrIndex = $(ValueData)
            else-ifstr(i) $(ValueName) == "ComPort"
                set ComPortValueIndex = $(ValueData)
            else-ifstr(i) $(ValueName) == "ConnectionType"
                set ConnectionIndex = $(ValueData)
            else-ifstr(i) $(ValueName) == "DirectEnable"      ;zachary
                set DirectEnableValue = $(ValueData)
            else-ifstr(i) $(ValueName) == "ComIRQ"
                set ComIrqValueIndex = $(ValueData)
            endif
       EndForListDo
    endif


    Debug-Output $(InfName)" IRQ_Level is "$(IRQValue)
    Debug-Output $(InfName)" I/o base is "$(IOBaseAddrValue)
    Debug-Output $(InfName)" Mem base is "$(MemAddrValue)
    Debug-Output $(InfName)" Com Port Number is "$(ComPortValue)

    set IRQValue = *($(IRQList), ~($(IRQValues),$(IRQValueIndex)))

    ifstr(i) $(IRQValue) == ""
        set IRQValue = *($(IRQList), 3)
Debug-Output $(InfName)" IRQ_Level is "$(IRQValue)
    endif

    set IOBaseAddrValue = *($(IOBaseAddrList), ~($(IOBaseAddrValues),$(IOBaseAddrIndex)))

    ifstr(i) $(IOBaseAddrValue) == ""
        set IOBaseAddrValue = *($(IOBaseAddrList), 1)
    endif


    set MemAddrValue = *($(MemAddrList), ~($(MemAddrValues),$(MemAddrIndex)))

    ifstr(i) $(MemAddrValue) == ""
        set MemAddrValue = *($(MemAddrList), 1)
    endif

; Zachary
    ifstr(i) $(DirectEnableValue) == ""
                set DirectEnableValue = 0
                set PcmciaValue = 1
    endif

    ifint $(DirectEnableValue) == 1
           set DirectEnableValue = "ON"
           set PcmciaValue = "OFF"
    else
           set DirectEnableValue = "OFF"
           set PcmciaValue = "ON"
    endif

        set CheckItemsIn = {$(DirectEnableValue)}  ;zachary

    set ConnectionValue = *($(ConnectionList), ~($(ConnectionValues),$(ConnectionIndex)))
    ifstr(i) $(ConnectionValue) == ""
        set ConnectionValue = *($(ConnectionList), 1)
    endif


    set ComPortValue = *($(ComPortList), ~($(ComPortValues),$(ComPortValueIndex)))
    ifstr(i) $(ComPortValue) == ""
        set ComPortValue = *($(ComPortList), 1)
    endif

;Kenny
    set ModemIOBaseAddressValue = *($(ModemIOBaseAddressList), ~($(ModemIOBaseAddressValues),$(ModemIOBaseAddressIndex)))
    ifstr(i) $(ModemIOBaseAddressValue) == ""
        set ModemIOBaseAddressValue = *($(ModemIOBaseAddressList), $(ComPortValue))
    endif


    set ComIrqValue = *($(ComIrqList), ~($(ComIrqValues),$(ComIrqValueIndex)))
    ifstr(i) $(ComIrqValue) == ""
        set ComIrqValue = *($(ComIrqList), 2)
    endif


    ;  Save the settings as they were read from the Registry.

;    Shell $(ParamInf) Param_SaveValues
;    Set CurrParamSettings = $($R0)
;
;   Put up the adapter configuration dialog if necessary.
;
;   Note that $(CurrParamSettings) has the old known parameter values.
;
adaptersetup = +


;    Shell "" DebugConfiguration "before displaying dialog"

    Set from = adapteroptions


adapteroptions = +
     ;zachary
        set CheckItemsIn = {$(DirectEnableValue)}


    ifint $(PCMCIAStatusFlag) == 8
        LoadLibrary "Disk 1" $(Dialog$(NT_VER)DllName) hLib
    else
        LoadLibrary "Disk 1" $(DialogNT3DllName) hLib
    endif

    read-syms FileDependentDlg$(!STF_LANGUAGE)

    Debug-Output $(InfName)" I/o base is "$(IOBaseAddrValue)



    ui start "InputDlg"  $(hLib)

    set ExitButton      = $(ButtonPressed)

    Debug-Output " ButtonPressed "$(ButtonPressed)


    FreeLibrary $(hLib)

    ifstr(i) $(DLGEVENT) == "CONTINUE"
                set IOBaseAddrIndex = $(Combo1Out)
                set IRQValueIndex = $(Combo2Out)
                set MemAddrIndex = $(Combo3Out)
                set ComPortValueIndex = $(Combo4Out)
                set ComIrqValueIndex = $(Combo6Out)
 ;old                 set SlotValueIndex = $(Combo6Out)
                set ConnectionIndex = $(Combo5Out)
;Kenny
                set ModemIOBaseAddressIndex = $(ComPortValueIndex)

                set DirectEnableValue  =  *($(CheckItemsOut), 1)  ;zachary


                set ExitButton      = $(ButtonPressed)

                ui pop 1

    else-ifstr(i) $(DLGEVENT) == "EXIT"
                set CommonStatus = STATUS_USERCANCEL
                Debug-Output "Action: exit. Bye."
                ui pop 1
                goto end
    else
                ;
                ; Unknow command
                ;
                ui pop 1


                Debug-Output "Action: unknown. Bye."
                goto end
    endif


    Debug-Output " Combo list out "$(ComboListItemsOut)


;
;   If installing, go create the necessary keys;
;   if configuring, they're already open.
;
skipoptions =+

    ifint $(OldVersionExisted) == $(TRUE)
        ifstr(i) $(!NTN_InstallMode) == configure
            goto writeparameters
        endif
    endif
    StartWait
    ;
    ; Add Software Component
    ;
    ifint $(OldVersionExisted) == $(FALSE)

        ifstr(i) $(!NTN_InstallMode) == "install"
           Ifstr(i) $(DoCopy) == "YES"

              Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) YES

              Ifint $($ShellCode) != $(!SHELL_CODE_OK)
                  Goto ShellCodeError
              Else-Ifstr(i) $($R0) == STATUS_FAILED
                  Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL"
                  ifint $($ShellCode) != $(!SHELL_CODE_OK)
                      goto ShellCodeError
                  endif
                  set Error = $($R0)
                  Goto fatal
              Else-Ifstr(i) $($R0) == STATUS_USERCANCEL
                  Goto successful
              Endif

;             Set SrcDir = $($R1)WINNT\
              Set SrcDir = $($R1)

           Endif

           install "Install-Option"

           ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS
              Shell $(UtilityInf) RegistryErrorString "UNABLE_COPY_FILE"
              ifint $($ShellCode) != $(!SHELL_CODE_OK)
                  goto ShellCodeError
              endif
              set Error = $($R0)
              goto fatal
           endif
        endif



        Shell $(UtilityInf), AddSoftwareComponent, $(Manufacturer), +
            $(ProductSoftwareName), +
            $(ProductSoftwareName), +
            $(ProductSoftwareTitle), $(STF_CONTEXTINFNAME), +
            $(ProductSoftwareImagePath), "kernel", "NDIS", {}, "",+
            $(NetEventDLL)

        Set OEM_ABANDON_SOFTWARE = TRUE

        ifint $($ShellCode) != $(!SHELL_CODE_OK)
            Debug-Output "ShellCode error"
            goto ShellCodeError
        endif
        ;
        ;   At this point:
        ;     $R1 contains the product version key handle;
        ;     $R2 contains the NetRules subkey handle;
        ;     $R3 contains the new Services key handle; and
        ;     $R4 contains the Parameters key
        ;     $R5 contains the Linkage Key
        ;
        set RegistryErrorIndex = $($R0)
        set KeyProduct      = $($R1)
        Set SoftNetRulesKey = $($R2)
        CloseRegKey $($R3)
        CloseRegKey $($R4)
        CloseRegKey $($R5)

        Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
            EndWait
            Debug-Output "Registry error: add software components"
            CloseRegKey $(KeyProduct)
            CloseRegKey $(SoftNetRulesKey)
            goto fatalregistry
        endif

        set NewValueList = {{SoftwareType,$(NoTitle),$(!REG_VT_SZ),$(SoftwareType)},+
                           {MajorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMajorVersion)},+
                           {MinorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMinorVersion)},+
                           {Title,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareTitle)},+
                           {Description,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareDescription)},+
                           {ServiceName,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareName)},+
                           {InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}}

        Shell  $(UtilityInf), AddValueList, $(KeyProduct), $(NewValueList)
        ifint $($ShellCode) != $(!SHELL_CODE_OK)
            Debug-Output "ShellCode error."
            goto ShellCodeError
        endif

        set RegistryErrorIndex = $($R0)

        Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
            EndWait
            Debug-Output "Registry error: add value list."
            CloseRegKey $(KeyProduct)
            CloseRegKey $(SoftNetRulesKey)
            goto fatalregistry
        endif

        set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareType)},+
                            {use,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareUse)}, +
                            {bindform,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareBindForm)}, +
                            {class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareClass)}, +
                            {bindable,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareBindable)}, +
                            {InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}}

        Shell  $(UtilityInf), AddValueList, $(SoftNetRulesKey), $(NewValueList)
        ifint $($ShellCode) != $(!SHELL_CODE_OK)
            Debug-Output "ShellCode error."
            goto ShellCodeError
        endif

        set RegistryErrorIndex = $($R0)

        CloseRegKey $(KeyProduct)
        CloseRegKey $(SoftNetRulesKey)

        Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
            EndWait
            Debug-Output "Resgitry error: add value list."
            goto fatalregistry
        endif
    endif
;
;   Create the HARDWARE\Netcard region and its corresponding service
;
    Shell $(UtilityInf), AddHardwareComponent, $(ProductHardwareName),$(STF_CONTEXTINFNAME),$(ProductKeyName)

    ifint $($R4) != -1
        Set OEM_ABANDON_OPTIONS = >($(OEM_ABANDON_OPTIONS), $(!NTN_SoftwareBase)"\Microsoft\Windows NT\CurrentVersion\NetworkCards\"$($R4))
    endif

    ifint $($ShellCode) != $(!SHELL_CODE_OK)
        Debug-Output "Cannot add hardware component"
        goto ShellCodeError
    endif

    set RegistryErrorIndex = $($R0)

    Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
        EndWait
        Debug-Output "Registry error: add hardware component"
        CloseRegKey $($R1)
        CloseRegKey $($R2)
        CloseRegKey $($R3)
        goto fatalregistry
    endif

    set KeyParameters = $($R3)
    set KeyAdapterRules = $($R2)
    set AdapterNumber = $($R4)

    set NewValueList = {{Manufacturer,$(NoTitle),$(!REG_VT_SZ),$(Manufacturer)},+
                       {Title,$(NoTitle),$(!REG_VT_SZ),"["$($R4)"] "$(ProductHardware$(Option)Title)},+
                       {Description,$(NoTitle),$(!REG_VT_SZ),$(ProductHardware$(Option)Description)},+
                       {ProductName,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareName)},+
                       {ServiceName,$(NoTitle),$(!REG_VT_SZ),$($R5)},+
                       {InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}}

    Shell  $(UtilityInf), AddValueList, $($R1), $(NewValueList)
    ifint $($ShellCode) != $(!SHELL_CODE_OK)
        Debug-Output "ShellCode error"
        goto ShellCodeError
    endif

    CloseRegKey $($R1)

    set TempProdName = """"$(ProductHardwareName)$(AdapterNumber)""""
    set TempBindForm = $(TempProdName)$(NetRuleHardwareBindForm)

    set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleHardwareType)},+
                        {bindform,$(NoTitle),$(!REG_VT_SZ),$(TempBindForm)}, +
                        {class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleHardwareClass)}, +
                        {InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}}

    Shell  $(UtilityInf), AddValueList, $(KeyAdapterRules), $(NewValueList)
    ifint $($ShellCode) != $(!SHELL_CODE_OK)
        Debug-Output "ShellCode error."
        goto ShellCodeError
    endif

    set RegistryErrorIndex = $($R0)

    Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
        EndWait
        Debug-Output "Resgitry error: add value list."
        CloseRegKey $(KeyParameters)
        CloseRegKey $(KeyAdapterRules)
        goto fatalregistry
    endif

    CloseRegKey $(KeyAdapterRules)

    goto writeparameters
;
;   REQUIRED:   $(KeyParameters) contains service Parameters key handle
;
writeparameters = +
    Shell $(UtilityInf), GetBusTypeNum
    set BusTypeNum = $($R1)
; Testing the BusNum. We are coding it to 0
    set BusNumValue = 0 ;
; End of BusNum
    ifint $($ShellCode) != $(!SHELL_CODE_OK)
        Debug-Output "ShellCode error."
        goto ShellCodeError
    endif


    set IRQValue = *($(IRQValues), ~($(IRQList),$(IRQValueIndex)))

    set IOBaseAddrValue = *($(IOBaseAddrValues), ~($(IOBaseAddrList),$(IOBaseAddrIndex)))

;zachary
    ifstr(i) $(DirectEnableValue) == "ON"
      set DirectEnableValue =  "1"
      set PcmciaValue = "0"
    else
      set DirectEnableValue =  "0"
      set PcmciaValue = "1"
    endif

;Kenny
    set ModemIOBaseAddressValue  = *($(ModemIOBaseAddressValues),  ~($(ModemIOBaseAddressList), $(ModemIOBaseAddressIndex)))

    set MemAddrValue = *($(MemAddrValues), ~($(MemAddrList),$(MemAddrIndex)))

;old     set SlotValue = *($(SlotValues), ~($(SlotList),$(SlotValueIndex)))

    set ComPortValue = *($(ComPortValues), ~($(ComPortList),$(ComPortValueIndex)))

    set ComIrqValue = *($(ComIrqValues), ~($(ComIrqList),$(ComIrqValueIndex)))

    set ConnectionValue = *($(ConnectionValues), ~($(ConnectionList),$(ConnectionIndex)))

    ifstr(i) $(NT_VER) == NT4
      ifint $(PCMCIAStatusFlag) == 8
        set NewValueList = {{IoBaseAddress,  $(NoTitle),$(!REG_VT_DWORD),$(ModemIOBaseAddressValue)},+
                        {IoBaseAddress_1,$(NoTitle),$(!REG_VT_DWORD),$(IOBaseAddrValue)},+
                        {IoLength,  $(NoTitle),$(!REG_VT_DWORD),8},+
                        {IoLength_1,$(NoTitle),$(!REG_VT_DWORD),32},+
                        {BusType,$(NoTitle),$(!REG_VT_DWORD),1},+
                        {BusNumber,  $(NoTitle),$(!REG_VT_DWORD),$(BusNumValue)},+
                        {MediaType,$(NoTitle),$(!REG_VT_DWORD),1},+
                        {DirectEnable,  $(NoTitle),$(!REG_VT_DWORD),$(DirectEnableValue)},+
                        {Pcmcia,$(NoTitle),$(!REG_VT_DWORD),$(PcmciaValue)},+
                        {NetworkAddress,$(NoTitle),$(!REG_VT_SZ),$(NetworkAddress)},+
                        {ModemFunction, $(NoTitle),$(!REG_VT_DWORD),1},+
                        {InterruptNumber,  $(NoTitle),$(!REG_VT_DWORD),$(IRQValue)},+
                        {PCCARDAttributeMemoryAddress,  $(NoTitle),$(!REG_VT_DWORD),$(MemAddrValue)},+
                        {PCCARDAttributeMemoryOffset,  $(NoTitle),$(!REG_VT_DWORD),61440},+
                        {PCCARDAttributeMemorySize,  $(NoTitle),$(!REG_VT_DWORD),4096},+
                        {ConnectionType,  $(NoTitle),$(!REG_VT_DWORD),$(ConnectionValue)},+
                        {ComPort,  $(NoTitle),$(!REG_VT_DWORD),$(ComPortValue)}}
;;                      {ComIRQ,  $(NoTitle),$(!REG_VT_DWORD),$(ComIrqValue)}}
      else
        set NewValueList = {{IoBaseAddress,  $(NoTitle),$(!REG_VT_DWORD),$(ModemIOBaseAddressValue)},+
                        {IoBaseAddress_1,$(NoTitle),$(!REG_VT_DWORD),$(IOBaseAddrValue)},+
                        {IoLength,  $(NoTitle),$(!REG_VT_DWORD),8},+
                        {IoLength_1,$(NoTitle),$(!REG_VT_DWORD),32},+
                        {BusType,$(NoTitle),$(!REG_VT_DWORD),1},+
                        {BusNumber,  $(NoTitle),$(!REG_VT_DWORD),$(BusNumValue)},+
                        {MediaType,$(NoTitle),$(!REG_VT_DWORD),1},+
                        {DirectEnable,  $(NoTitle),$(!REG_VT_DWORD),$(DirectEnableValue)},+
                        {Pcmcia,$(NoTitle),$(!REG_VT_DWORD),0},+
                        {NetworkAddress,$(NoTitle),$(!REG_VT_SZ),$(NetworkAddress)},+
                        {InterruptNumber,  $(NoTitle),$(!REG_VT_DWORD),$(IRQValue)},+
                        {PCCARDAttributeMemoryAddress,  $(NoTitle),$(!REG_VT_DWORD),$(MemAddrValue)},+
                        {PCCARDAttributeMemoryOffset,  $(NoTitle),$(!REG_VT_DWORD),61440},+
                        {PCCARDAttributeMemorySize,  $(NoTitle),$(!REG_VT_DWORD),4096},+
                        {ConnectionType,  $(NoTitle),$(!REG_VT_DWORD),$(ConnectionValue)},+
                        {ComPort,  $(NoTitle),$(!REG_VT_DWORD),$(ComPortValue)},+
                        {ComIRQ,  $(NoTitle),$(!REG_VT_DWORD),$(ComIrqValue)}}



      endif
    else   ; for NT351
    set NewValueList = {{IoBaseAddress,  $(NoTitle),$(!REG_VT_DWORD),$(ModemIOBaseAddressValue)},+
                        {IoBaseAddress_1,$(NoTitle),$(!REG_VT_DWORD),$(IOBaseAddrValue)},+
                        {IoLength,  $(NoTitle),$(!REG_VT_DWORD),8},+
                        {IoLength_1,$(NoTitle),$(!REG_VT_DWORD),32},+
                        {BusType,$(NoTitle),$(!REG_VT_DWORD),1},+
                        {BusNumber,  $(NoTitle),$(!REG_VT_DWORD),$(BusNumValue)},+
                        {MediaType,$(NoTitle),$(!REG_VT_DWORD),1},+
                        {DirectEnable,  $(NoTitle),$(!REG_VT_DWORD),$(DirectEnableValue)},+
                        {Pcmcia,$(NoTitle),$(!REG_VT_DWORD),$(PcmciaValue)},+
                        {NetworkAddress,$(NoTitle),$(!REG_VT_SZ),$(NetworkAddress)},+
                        {InterruptNumber,  $(NoTitle),$(!REG_VT_DWORD),$(IRQValue)},+
                        {PCCARDAttributeMemoryAddress,  $(NoTitle),$(!REG_VT_DWORD),$(MemAddrValue)},+
                        {PCCARDAttributeMemoryOffset,  $(NoTitle),$(!REG_VT_DWORD),61440},+
                        {PCCARDAttributeMemorySize,  $(NoTitle),$(!REG_VT_DWORD),4096},+
                        {ConnectionType,  $(NoTitle),$(!REG_VT_DWORD),$(ConnectionValue)},+
                        {ComPort,  $(NoTitle),$(!REG_VT_DWORD),$(ComPortValue)},+
                        {ComIRQ,  $(NoTitle),$(!REG_VT_DWORD),$(ComIrqValue)}}
    endif


    Shell  $(UtilityInf), AddValueList, $(KeyParameters), $(NewValueList)

    CloseRegKey $(KeyParameters)

    ifint $($ShellCode) != $(!SHELL_CODE_OK)
        Debug-Output "ShellCode error."
        goto ShellCodeError
    endif

    set RegistryErrorIndex = $($R0)

    Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
        Debug-Output "Registry error: Add value list"
        goto fatalregistry
    endif

;+ For CardWizard 1-16-98
    OpenRegKey $(!REG_H_LOCAL) "" $(CardwizDataBase) $(MAXIMUM_ALLOWED) KeyCardwiz
    ifstr $(KeyCardwiz) == $(KeyNull)
        Debug-Output "D65: Registry Open Fail -- CardwizDataBase"
        goto CardWizEnd
    endif
    Debug-Output "D65: Open CardwizDataBase Registry Successful"

    OpenRegKey $(!REG_H_LOCAL) "" $(CWZNICDataBase) $(MAXIMUM_ALLOWED) KeyDataBase2
    ifstr $(KeyDataBase2) == $(KeyNull)
        CreateRegKey $(KeyCardwiz) {"D-Link\DMF-560TXD DirectPort PC Card",$(NoTitle),GenericClass} "" $(MAXIMUM_ALLOWED) "" KeyDataBase2

        ifstr $(KeyDataBase2) == $(KeyNull)
            goto CardWizEnd
        endif
    endif

    Debug-Output "D65: Cardwiz Set Keyword value -- Driver"
    SetRegValue $(KeyDataBase2) {"MacDriverHandle",$(NoTitle),$(!REG_VT_DWORD),0}
    SetRegValue $(KeyDataBase2) {"MacDriverName",$(NoTitle),$(!REG_VT_SZ),"LMNDIS3"}
    SetRegValue $(KeyDataBase2) {"MacDriverState",$(NoTitle),$(!REG_VT_DWORD),1}
    SetRegValue $(KeyDataBase2) {"MacDriverVersion",$(NoTitle),$(!REG_VT_DWORD),0x300}
    SetRegValue $(KeyDataBase2) {"MacSwapCapability",$(NoTitle),$(!REG_VT_DWORD),2}

    CloseRegKey $(KeyDataBase2)
    CloseRegKey $(KeyCardwiz)

CardWizEnd = +
;- For CardWizard 1-16-98
;;;;; andge

    OpenRegKey $(!REG_H_LOCAL) "" $(PCCardDataBase) $(MAXIMUM_ALLOWED) KeyPCCard
    ifstr $(KeyPCCard) == $(KeyNull)
        Debug-Output "D65: Registry Open Fail -- PCCardDataBase"
;Kenny        goto fatalregistry
        goto NT350
    endif
    Debug-Output "D65: Open PCCardDataBase Registry Successful"

    OpenRegKey $(!REG_H_LOCAL) "" $(NICDataBase) $(MAXIMUM_ALLOWED) KeyDataBase
    ifstr $(KeyDataBase) == $(KeyNull)
        CreateRegKey $(KeyPCCard) {"D-Link\DMF-560TXD DirectPort PC Card",$(NoTitle),GenericClass} "" $(MAXIMUM_ALLOWED) "" KeyDataBase
        ifstr $(KeyDataBase) == $(KeyNull)
            CloseRegKey $(KeyPCCard)
            goto fatalregistry
        endif
    endif

    Debug-Output "D65: Set Keyword value -- Driver"
    SetRegValue $(KeyDataBase) {"AttributeMemorySize",$(NoTitle),$(!REG_VT_DWORD),65536}
    SetRegValue $(KeyDataBase) {"Driver",$(NoTitle),$(!REG_VT_SZ),"LMNDIS"}
    SetRegValue $(KeyDataBase) {DeviceType,$(NoTitle),$(!REG_VT_SZ),"NET"}

    CloseRegKey $(KeyDataBase)
    CloseRegKey $(KeyPCCard)

;;tang begin

    ifstr(i) $(NT_VER) == NT4
     ifint $(PCMCIAStatusFlag) != 8
       OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Serial\Parameters\SerialCombo" $(MAXIMUM_ALLOWED) NewSerialHandle
       Ifstr $(NewSerialHandle) == $(KeyNull)
               OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Serial\Parameters" $(MAXIMUM_ALLOWED) SerialKey
               CreateRegKey $(SerialKey) {"SerialCombo",0,GenericClass} "" $(MAXIMUM_ALLOWED) "" NewSerialHandle
               CloseRegKey $(SerialKey)
       endif
       set NewValueList     = {{DosDevices,       $(NoTitle),$(!REG_VT_SZ),      "COM"$(ComPortValue)},+       ; "COMx"
                              {ForceFifoEnable,  $(NoTitle),$(!REG_VT_DWORD),   0},+
                              {Interrupt,        $(NoTitle),$(!REG_VT_DWORD),   $(ComIrqValue)},+
                              {PortAddress,      $(NoTitle),$(!REG_VT_DWORD),   $(ModemIOBaseAddressValue)}}
       Shell  $(UtilityInf), AddValueList, $(NewSerialHandle), $(NewValueList)
       CloseRegKey $(NewSerialHandle)

       ; add comm port info to HARDWARE\DEVICEMAP\SERIALCOMM section
       OpenRegKey $(!REG_H_LOCAL) "" "HARDWARE\DEVICEMAP\SERIALCOMM" $(MAXIMUM_ALLOWED) NewSerialHandle
       Ifstr $(NewSerialHandle) == $(KeyNull)
              OpenRegKey $(!REG_H_LOCAL) "" "HARDWARE\DEVICEMAP" $(MAXIMUM_ALLOWED) SerialKey
              CreateRegKey $(SerialKey) {"SERIALCOMM",0,GenericClass} "" $(MAXIMUM_ALLOWED) "" NewSerialHandle
              CloseRegKey $(SerialKey)
       endif
       SetRegValue $(NewSerialHandle) {"SerialCombo",$(NoTitle),$(!REG_VT_SZ),"COM"$(ComPortValue)}
       CloseRegKey $(NewSerialHandle)

       ; add comm port info to SOFTWARE\Microsoft\Windows NT\CurrentVersion\Ports section
       OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows NT\CurrentVersion\Ports" $(MAXIMUM_ALLOWED) NewSerialHandle
       Ifstr $(MyNewSerialHandle) == $(KeyNull)
              OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows NT\CurrentVersion" $(MAXIMUM_ALLOWED) SerialKey
              CreateRegKey $(SerialKey) {"Ports",0,GenericClass} "" $(MAXIMUM_ALLOWED) "" NewSerialHandle
              CloseRegKey $(SerialKey)
       endif
       SetRegValue $(MyNewSerialHandle) {"COM"$(ComPortValue)":",$(NoTitle),$(!REG_VT_SZ), "9600,n,8,1"}
       CloseRegKey $(MyNewSerialHandle)

     endif

    else     ; NT351
       OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Serial\Parameters\SerialCombo" $(MAXIMUM_ALLOWED) NewSerialHandle
       Ifstr $(NewSerialHandle) == $(KeyNull)
               OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Serial\Parameters" $(MAXIMUM_ALLOWED) SerialKey
               CreateRegKey $(SerialKey) {"SerialCombo",0,GenericClass} "" $(MAXIMUM_ALLOWED) "" NewSerialHandle
               CloseRegKey $(SerialKey)
       endif
       set NewValueList     = {{DosDevices,       $(NoTitle),$(!REG_VT_SZ),      "COM"$(ComPortValue)},+       ; "COMx"
                              {ForceFifoEnable,  $(NoTitle),$(!REG_VT_DWORD),   0},+
                              {Interrupt,        $(NoTitle),$(!REG_VT_DWORD),   $(ComIrqValue)},+
                              {PortAddress,      $(NoTitle),$(!REG_VT_DWORD),   $(ModemIOBaseAddressValue)}}
       Shell  $(UtilityInf), AddValueList, $(NewSerialHandle), $(NewValueList)
       CloseRegKey $(NewSerialHandle)

       ; add comm port info to HARDWARE\DEVICEMAP\SERIALCOMM section
       OpenRegKey $(!REG_H_LOCAL) "" "HARDWARE\DEVICEMAP\SERIALCOMM" $(MAXIMUM_ALLOWED) NewSerialHandle
       Ifstr $(NewSerialHandle) == $(KeyNull)
              OpenRegKey $(!REG_H_LOCAL) "" "HARDWARE\DEVICEMAP" $(MAXIMUM_ALLOWED) SerialKey
              CreateRegKey $(SerialKey) {"SERIALCOMM",0,GenericClass} "" $(MAXIMUM_ALLOWED) "" NewSerialHandle
              CloseRegKey $(SerialKey)
       endif
       SetRegValue $(NewSerialHandle) {"SerialCombo",$(NoTitle),$(!REG_VT_SZ),"COM"$(ComPortValue)}
       CloseRegKey $(NewSerialHandle)

       ; add comm port info to SOFTWARE\Microsoft\Windows NT\CurrentVersion\Ports section
       OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows NT\CurrentVersion\Ports" $(MAXIMUM_ALLOWED) NewSerialHandle
       Ifstr $(MyNewSerialHandle) == $(KeyNull)
              OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows NT\CurrentVersion" $(MAXIMUM_ALLOWED) SerialKey
              CreateRegKey $(SerialKey) {"Ports",0,GenericClass} "" $(MAXIMUM_ALLOWED) "" NewSerialHandle
              CloseRegKey $(SerialKey)
       endif
       SetRegValue $(MyNewSerialHandle) {"COM"$(ComPortValue)":",$(NoTitle),$(!REG_VT_SZ), "9600,n,8,1"}
       CloseRegKey $(MyNewSerialHandle)

    endif
;;tang end


NT350 = +
;;;;; end of andge

    EndWait

    goto successful

;-----------------------------------------------
; Binding section
;-----------------------------------------------
bindingadapter =+
    set Error = "Binding: Sorry, not yet implemented."
    goto fatal

;-----------------------------------------------
; Removeadapter section
;-----------------------------------------------

removeadapter = +
    Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase)
        ; Remove Software Component
        Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), +
            $(ProductSoftwareName)
        ifint $($ShellCode) != $(!SHELL_CODE_OK)
            Debug-Output "ShellCode error"
            goto ShellCodeError
        endif

        set RegistryErrorIndex = $($R0)

        Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
            goto fatalregistry
        endif
    else
        Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), +
            $(ProductSoftwareName), $(!NTN_RegBase)
        ifint $($ShellCode) != $(!SHELL_CODE_OK)
            Debug-Output "ShellCode error"
            goto ShellCodeError
        endif

        set RegistryErrorIndex = $($R0)

        Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
            goto fatalregistry
        endif

        ifstr(i) $(NT_VER) == NT3
            OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Serial\Parameters" $(MAXIMUM_ALLOWED) SerialHandle
            DeleteRegTree $(SerialHandle) SerialCombo
            CloseRegKey $(SerialHandle)
        else-ifint $(PCMCIAStatusFlag) != 8
            OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Serial\Parameters" $(MAXIMUM_ALLOWED) SerialHandle
            DeleteRegTree $(SerialHandle) SerialCombo
            CloseRegKey $(SerialHandle)
        endif

    endif

    goto end

;-----------------------------------------------
; Upgrade Software section
;-----------------------------------------------

UpgradeSoftware = +
    ;
    ; First determine whether we want to do upgrade or update for software
    ; or hardware component. Then we will determine whether the Mode is
    ; update or upgrade.
    ;
    ; If the same version of the product existed in the registry, we do
    ; update. Otherwise, we will do a upgrade
    ;
    ifstr(i) $(ProductKeyName) == $(!NTN_RegBase)
        ; Upgrade software component
        ;
        ; see whether the same version exist or not
        ;
        OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct

        Ifstr $(KeyProduct) != $(KeyNull)
            GetRegValue $(KeyProduct),"MajorVersion", VersionInfo
            set Version = *($(VersionInfo), 4)


            ;
            ; Update the binaries
            ;
            Shell $(UtilityInf), GetInfFileNameFromRegistry, $(KeyProduct)

            ifint $($ShellCode) != $(!SHELL_CODE_OK)
                Debug-Output "ShellCode error"
                goto ShellCodeError
            endif

            set !UG_Filename = $($R0)

            ifstr(i) $(!UG_Filename) != ""
                install "Install-Update"
                ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS
                    goto fatal
                endif
            endif

            ; Upgrade the version number
            ;
            SetRegValue $(KeyProduct) {MajorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMajorVersion)}
            SetRegValue $(KeyProduct) {MinorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMinorVersion)}

            ;
            ; do nothing for update
            ;
            ifint $(Version) != $(ProductVersion)
               ;
               ; If the major version number is not the same,
               ; it is major upgrade. So let Upgrade the product
               ;
               ;
               ; make other upgrade change if necessary
               ;
            endif
            CloseRegKey $(KeyProduct)
        else
            ;
            ; Cannot Open software key, goto ERROR
            ;
            goto fatalregistry
        endif
    else
        ;
        ; upgrade/update hardware component
        ; There is no different between upgrade and update for hardware
        ; component
        ;
        ; 1. Get the Service Name
        ; 2. Change the NetRule section if necessary
        ;
        OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) +
              $(MAXIMUM_ALLOWED) NetworkCardKey
        Ifstr(i) $(NetworkCardKey) != $(KeyNull)
            ;
            ; Get Service name
            ;
            GetRegValue $(NetworkCardKey),"ServiceName", ServiceNameInfo
            set ServiceName = *($(ServiceNameInfo), 4)

            ;
            ; Change the NetRule if necessary
            ;
            OpenRegKey $(NetworkCardKey) "" "NetRules" +
                $(MAXIMUM_ALLOWED) NetRuleKey
            Ifstr(i) $(NetRuleKey) != $(KeyNull)
                ;
                ; Make the change....
                ;
            else
                ;
                ; Error, cannot open net rules key
                ;
                goto fatalregistry
            endif

            CloseRegKey $(NetRules)
            CloseRegKey $(NetworkCardKey)
        else
            ;
            ; Error, cannot open network card key
            ;
            goto fatalregistry
        endif
        ;
        ; 3. Change the service section of the hardware. i.e.,
        ;    ParameterName change, value change, etc.
        ;
        OpenRegKey $(!REG_H_LOCAL) "" +
              $(!NTN_ServiceBase)"\"$(ServiceName) +
              $(MAXIMUM_ALLOWED) ServiceKey

        Ifstr(i) $(ServiceKey) != $(KeyNull)
            ;
            ; Get the ServiceKey to change the Start value
            ; or Type value. Or open Parameters key to
            ; change the hardware parameters if necessary.
            ;
            CloseRegKey $(ServiceKey)
        else
            ;
            ; Error, cannot open network card key
            ;
            goto fatalregistry
        endif
    endif

    goto end
    ;
    ; End of Upgrade Software
    ;

;
;  Escape hatches
;
successful = +
    goto end

abandon = +
    ForListDo $(OEM_ABANDON_OPTIONS)
        Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), +
            $(ProductSoftwareName), $($)
        ifint $($ShellCode) != $(!SHELL_CODE_OK)
            Debug-Output "ShellCode error"
            goto ShellCodeError
        endif

        set RegistryErrorIndex = $($R0)

        Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
            goto fatalregistry
        endif
    EndForListDo

    Ifstr(i) $(OEM_ABANDON_SOFTWARE) == TRUE
        ; Remove Software Component
        Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), +
            $(ProductSoftwareName), FALSE
        ifint $($ShellCode) != $(!SHELL_CODE_OK)
            Debug-Output "ShellCode error"
            goto ShellCodeError
        endif

        set RegistryErrorIndex = $($R0)

        Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
            goto fatalregistry
        endif
    endif

    goto end

;
; warning display
;
warning = +
    Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "WARNING", $(Error)
    ifint $($ShellCode) != $(!SHELL_CODE_OK)
        goto ShellCodeError
    endif
    ifstr(i) $($R1) == "OK"
        goto $(to)
    else-ifstr(i) $($R1) == "CANCEL"
        goto $(from)
    else
        goto "end"
    endif
;
; non fatal error display
;
nonfatalinfo = +
    Set Severity = STATUS
    Set CommonStatus = STATUS_USERCANCEL
    goto nonfatalmsg
nonfatal = +
    Set Severity = NONFATAL
    goto nonfatalmsg
nonfatalmsg = +
    ifstr(i) $(Error) == ""
        Set Severity = NONFATAL
        Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL"
        ifint $($ShellCode) != $(!SHELL_CODE_OK)
            goto ShellCodeError
        endif
        set Error = $($R0)
    endif
    Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), $(Severity), $(Error)
    ifint $($ShellCode) != $(!SHELL_CODE_OK)
        goto ShellCodeError
    endif
    ifstr(i) $($R1) == "OK"
        goto $(from)
    else
        goto "end"
    endif

;
;  Registry is broken
;
fatalregistry = +
    Shell $(UtilityInf) RegistryErrorString $(RegistryErrorIndex)
    ifint $($ShellCode) != $(!SHELL_CODE_OK)
        goto ShellCodeError
    endif
    set Error = $($R0)
    goto fatal
;
;  Netcard detection failure
;
fataldetect = +
    Shell $(UtilityInf),RegistryErrorString,CANNOT_DETECT
    ifint $($ShellCode) != $(!SHELL_CODE_OK)
        Debug-Output "ShellCode error: cannot get an error string."
        goto ShellCodeError
    endif
    set Error = $($R0)
    Goto fatal
;
; fatal error display
;
fatal = +
    ifstr(i) $(Error) == ""
        Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL"
        ifint $($ShellCode) != $(!SHELL_CODE_OK)
            goto ShellCodeError
        endif
        set Error = $($R0)
    endif
    Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "FATAL", $(Error)
    ifint $($ShellCode) != $(!SHELL_CODE_OK)
        goto ShellCodeError
    endif

    goto setfailed

;
;  Shelling error
;
ShellCodeError = +
    set DlgType      = "MessageBox"
    set STF_MB_TITLE = $(ShellCodeErrorTitle)
    set STF_MB_TEXT  = $(ShellCodeErrorText)
    set STF_MB_TYPE  = 1
    set STF_MB_ICON  = 3
    set STF_MB_DEF   = 1
    ui start "Error Message"
    goto setfailed

setfailed = +
    set CommonStatus = STATUS_FAILED
    ;
    ; if OEM_ABANDON_ON == TRUE, then remove the registry entries
    ;
    ifstr(i) $(OEM_ABANDON_ON) == TRUE
        set OEM_ABANDON_ON = FALSE
        goto abandon
    endif
    goto end

end = +
    goto term

term = +

    Return $(CommonStatus)

[DebugConfiguration]

    Set InfName = "inf"
    Debug-Output $(InfName)" **CONFIGURATION STATE: "$($0)
    Debug-Output $(InfName)" IRQ_Level is "$(!p:IRQValue)
    Debug-Output $(InfName)" IOBaseAddrValue is "$(!p:IOBaseAddrValue)
    Debug-Output $(InfName)" MemAddrValue is "$(!p:MemAddrValue)
;old     Debug-Output $(InfName)" SlotNumber is "$(!p:SlotValue)
    Debug-Output $(InfName)" ComPortNumber is "$(!p:ComPortValue)
    Debug-Output $(InfName)" TransceiverValue is "$(!p:TransceiverValue)
    Debug-Output $(InfName)" MemBaseAddrDec is "$(!p:MemBaseAddrDec)
    Debug-Output $(InfName)" MappedValue is "$(!p:MappedValue)

    return


;***************************************************************
;  INSTALL SECTIONS
;***************************************************************
[Install-Option]
    set STF_VITAL = ""

    ifstr(i) $(AddCopy) == "YES"

        ;
        ; Add the files to the copy list
        ;
        ;  BUGBUG: eliminate the "nt2" in the next line when Sunil fixes
        ;      the other INF files
        ;
        AddSectionFilesToCopyList Files-$(NT_VER) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers

    endif

    ifstr(i) $(DoCopy) == "YES"

       ;
       ; Copy files in the copy list
       ;
       set !STF_NCPA_FLUSH_COPYLIST = TRUE
       CopyFilesInCopyList

    endif

    Exit

[Install-Update]
   set STF_VITAL        = ""
   set STF_OVERWRITE    = "VERIFYSOURCEOLDER"
   ;set STF_VERSION     = "YES"

   AddSectionFilesToCopyList Files-$(NT_VER) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers
   AddSectionFilesToCopyList Files-Inf $(SrcDir) $(!STF_WINDOWSSYSPATH)

   set !STF_NCPA_FLUSH_COPYLIST = TRUE
   CopyFilesInCopyList

   exit


[Install-Dll]
   set STF_VITAL        = ""

   ifstr(i) $(NT_VER) == NT3
      AddSectionFilesToCopyList Files-$(NT_VER)-Dll $(SrcDir) $(!STF_WINDOWSSYSPATH)
   else
     ifint $(PCMCIAStatusFlag) == 8
       AddSectionFilesToCopyList Files-$(NT_VER)-Dll $(SrcDir) $(!STF_WINDOWSSYSPATH)
     else
       AddSectionFilesToCopyList Files-NT3-Dll $(SrcDir) $(!STF_WINDOWSSYSPATH)
     endif
   endif
   set !STF_NCPA_FLUSH_COPYLIST = TRUE
   CopyFilesInCopyList
   exit





[Source Media Descriptions]
    1  = "D-Link DMF-560TXD DirectPort PC Card Driver Disk"
[ProductType]
STF_PRODUCT  = Winnt
STF_PLATFORM = I386


[Files-Inf]
1, oemsetnt.inf,    SIZE=2000,     RENAME=$(!UG_Filename)

[Files-NT4]
1, LMNDIS3.SYS , SIZE=88888
1, MDMLMX.INF, SIZE=60000, DESTINATION=$(!STF_WINDOWSPATH)\INF

[Files-NT4-Dll]
1, LMNDIS4.dll,   SIZE=3000

[Files-NT3]
1, LMNDIS3.SYS , SIZE=88888
1, MODEM.INF, SIZE=250000, BACKUP=MODEM.BAK, DESTINATION=$(!STF_WINDOWSSYSPATH)\RAS DECOMPRESS RENAME=MODEM.INF
1, MDMLMX.INF, SIZE=60000, DESTINATION=$(!STF_WINDOWSPATH)\INF

[Files-NT3-Dll]
1, LMNDIS3.dll,   SIZE=3000



[LanguagesSupported]
    ENG

[OptionsTextENG]
    LMNDIS     = "D-Link DMF-560TXD DirectPort PC Card"

[FileConstantsENG]
ProCaption   = "Windows NT Setup"
ProCancel    = "Cancel"
ProCancelMsg = "Windows NT Networking is not correctly installed.  "+
               "Are you sure you want to cancel copying files?"
ProCancelCap = "Network Setup Message"
ProText1     = "Copying:"
ProText2     = "To:"

FunctionTitle   = $(GenericFunctionName)" Setup"

ProductSoftwareDescription = $(GenericDriverName)
ProductHardwareDescription = $(GenericAdapterName)
ProductHardwareLMNDISDescription="D-Link DMF-560TXD DirectPort PC Card"

ProductSoftwareTitle =       $(GenericDriverName)
ProductHardwareLMNDISTitle =       $(GenericAdapterName)

DialogNT3DllName   = "LMNDIS3.dll"
DialogNT4DllName   = "LMNDIS4.dll"


IRQList  = ^(IRQChoices, 1)
IRQValues = ^(IRQChoices, 2)

IOBaseAddrList = ^(IOBaseAddrChoices, 1)
IOBaseAddrValues = ^(IOBaseAddrChoices, 2)

ModemIOBaseAddressList   = ^(ModemIOBaseAddressChoices,1)
ModemIOBaseAddressValues = ^(ModemIOBaseAddressChoices,2)

MemAddrList = ^(MemAddrChoices, 1)
MemAddrValues = ^(MemAddrChoices, 2)

;old SlotList  = ^(SlotChoices, 1)
;old SlotValues = ^(SlotChoices, 2)

ComPortList = ^(ComPortChoices, 1)
ComPortValues = ^(ComPortChoices, 2)

ComIrqList = ^(ComIrqChoices, 1)
ComIrqValues = ^(ComIrqChoices, 2)

ConnectionList  = ^(ConnectionChoices, 1)
ConnectionValues = ^(ConnectionChoices, 2)

[DialogConstantsENG]
Help        = "&Help"
Exit        = "Cancel"
OK          = "OK"
HelpContext = ""
Continue    = "Continue"
Cancel      = "Cancel"

[MemoryMappedChoicesENG]
Map_1 = 1, "ON"
Map_2 = 0, "OFF"

[FileDependentDlgENG]

DlgText = "Please select values for the follwing fields:"

DlgType = "RadioCombination"
DlgTemplate = "Kenny"
Caption = $(FunctionTitle)


CBOptionsGreyed = {}
NotifyFields = {NO, NO}

Combo1Label = "I/O &Base:"
Combo2Label = "&Interrupt:"
Combo3Label = "&Memory:"
Combo4Label = "COM &Port:"
;old Combo6Label = "&Socket Number:"
Combo5Label = "Connection &Type:"
Combo6Label = "&COM IRQ:"
Check1 = "&Direct Enable"   ;zachary

Combo1List = $(IOBaseAddrList)
Combo1Out  = $(IOBaseAddrValue)

Combo2List = $(IRQList)
Combo2Out  = $(IRQValue)

Combo3List = $(MemAddrList)
Combo3Out  = $(MemAddrValue)

Combo4List = $(ComPortList)
Combo4Out  = $(ComPortValue)

;old Combo6List = $(SlotList)
;old Combo6Out  = $(SlotValue)

Combo5List = $(ConnectionList)
Combo5Out  = $(ConnectionValue)

Combo6List = $(ComIrqList)
Combo6Out  = $(ComIrqValue)

ComboListItemsIn  = {Combo1List,Combo2List,Combo3List,Combo4List,Combo5List,Combo6List}
ComboListItemsOut = {Combo1Out,Combo2Out,Combo3Out,Combo4Out,Combo5Out,Combo6Out}

;zachary
CheckItemsIn = {$(DirectEnableValue)}   ;zachary
CheckItemsOut = {Check1Out}   ;zachary



EditTextIn = ""
EditTextLim = ""





[IRQChoices]
IRQ_1 = "3",3
IRQ_2 = "4",4
IRQ_3 = "5",5
IRQ_4 = "7",7
IRQ_5 = "9",9
IRQ_6 = "10",10
IRQ_7 = "11",11
IRQ_8 = "12",12
;IRQ_8 = "15",15

[IOBaseAddrChoices]
IOBase_1 = "0x300",768
IOBase_2 = "0x320",800
IOBase_3 = "0x340",832
IOBase_4 = "0x220",544


[ModemIOBaseAddressChoices]
MdmIOBase_1  = "1",1016
MdmIOBase_2  = "2",760
MdmIOBase_3  = "3",1000
MdmIOBase_4  = "4",744


[MemAddrChoices]
Memory_1 = "0xD0000",851968
Memory_2 = "0xD4000",868352
Memory_3 = "0xD8000",884736
Memory_4 = "0xDC000",901120

[ConnectionChoices]
Connect_0 = "AutoSense", 5
Connect_1 = "100Mbps Half Duplex", 4
Connect_2 = "10Mbps Full Duplex", 2
Connect_3 = "10Mbps Half Duplex", 0

;old [SlotChoices]
;old Slot_1 = "0",0
;old Slot_2 = "1",1
;old Slot_3 = "2",2
;old Slot_4 = "3",3

[ComPortChoices]
ComPort_1 = "2",2
ComPort_2 = "3",3
ComPort_3 = "4",4

[ComIrqChoices]
ComIrq_1 = "2",2
ComIrq_2 = "3",3
ComIrq_3 = "4",4
ComIrq_4 = "5",5
ComIrq_5 = "6",6
ComIrq_6 = "7",7
ComIrq_7 = "8",8
ComIrq_8 = "9",9
ComIrq_9 = "10",10
ComIrq_10= "11",11
ComIrq_11= "12",12
ComIrq_12= "13",13
ComIrq_13= "14",14
;ComIrq_14= "15",15


Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: ftp, load: 2.20