*******************************************************************
* ACCTON TECHNOLOGY CORPORATION *
* EN1207D SERIES PCI FAST ETHERNET ADAPTER *
* SCO UNIX STREAM DRIVER *
* *
* Copyright (C) 1998 Accton Technology Corporation *
* All Rights Reserved. *
*******************************************************************
The unix driver contained in the directory \SCO is for the
following PCI Ethernet adapter:
Accton EN1207D Series PCI Fast Ethernet Adapter
Contents:
---------
A.) Installing MDI Unix Driver for SCO ODT 5.0
B.) Installing LLI Unix Driver for SCO 3.2.4 (ODT 3.0)
File Description
================
5.X\ SCO ODT 5.0 MDI Unix Driver
3.X\ SCO 3.2.4 (ODT 3.0) LLI Unix Driver
SCOUNIX.TXT this file
A.) Installing MDI Unix Driver for SCO ODT 5.0
==============================================
1. Log into the UNIX system as supervisor (root) and enter Maintenance mode.
(Note: Make sure that the current directory is "/"
using UNIX command - pwd.)
Please follow the following steps to uncompress the package file:
> cd /tmp (and insert the floppy in the proper drive, i.e. a:)
> doscp a:/sco/5.x/vol.000 ./VOL.000.000
Now the installation directory is ready for use.
3. The following sections describe configuration of the driver.
It is suggested that you should carry out these instructions in a
singler-user environment.
Run the custom utility and select the "Install new package" option.
Select Media Type "Media Image" and type Image Directory "/tmp "
It will prompt with "Accton EN1207D-TX PCI Fast Ethernet Adapter
(ver 1.0.2)"
After running the custom utility and the new package is installed,
you should use the "netconfig" command to add the driver into your
system as described in step 4 below.
4. Run "netconfig". Add the desired chain.
5. When the chain has been configured, select 'q' from the
netconfig menu. and relink the kernel at the prompt.
6. To activate the adapter, you must reboot. When the system
boots, you should see the following data dispalyed among the
configuration messages:
%ethernet 0xD800-0xD81F 11 - type=100 addr=00-00-e8-xx-xx-xx
.
.
.
auto mode
choice is auto negotiation mode
Speed is 100 Mbps
with the appropriate I/O addresses, IRQ, Adapter Type ,IEEE address and
medium mode (auto,100full,100half,10full,10half).
The display of the last three bytes of the IEEE address depends on the
adapter currently plugged into your system.
7. If you encounter any problems during installation,
(i.e., an error message appears on screen) call your dealer for assistance.
B. Installing LLI Unix Driver for SCO 3.2.4 (ODT 3.0)
======================================================
1. Plug the EN1207D-TX PCI Fast Ethernet Adapter into the PCI slot
on your PC machine.
2. Turn ON the machine and log in as "root" user. (In maintenance mode)
3. Insert the EN1207D-TX SCO UNIX Driver diskette to floppy A: and
enter the following command from the Unix Shell to install the
SCO Unix driver.
# cd /tmp
# doscp a:/sco/3.x/install .
# chmod +x install
# ./install
4. The screen will prompt you with the following message,
Install EN1207D-TX PCI Fast Ethernet Adapter LLI Driver
Please input source path ? (ex.: a:/sco/3.x)
5. Enter the driver's full path (a:/sco/3.x) and press the ENTER key
to start copying the driver files to the Unix system.
6. Run the "netconfig" command from Unix shell.
# netconfig
7. Select "1. Add a chain" from the configuring chain options.
8. Select "4. sco_tcp SCO TCP/IP for UNIX" from the configuring
protocol options.
9. Select "18. r7e0 Accton EN1207D-TX Fast Ethernet PCI Adapter LLI
Driver, board 0" from the configuring driver options.
10. The system will prompt you with the following message to complete
configuring the driver chain,
...
Add chain sco_tcp->r7e0 (y/n): y
...
Enter auto, force 100 or 10bps: (auto 10 100) [auto]
or 'q' to quit: (press Enter key)
...
Enter the internet address of this interface: 203.70.236.92
Enter the netmask for this interface (default: 255.255.255.0):
(press Enter key)
Does the interface use a broadcast address of all 1's? (y/n)
(default: y): (press Enter key)
Enter the broadcast address for this interface (default:
203.70.236.255): (press Enter key)
...
Are these values correct? (y/n): y
...
Enter local host name or enter q to quit [sco324]: (press Enter key)
...
32 Pseudo ttys ...
...
Select an option or enter q to quit [q]: (press Enter key)
...
256 TCP connections ...
...
Select an option or enter q to quit [q]: (press Enter key)
...
11. Select "q. Quit" from the configuring chain options.
12. The system will prompt you with the following message to relink
the system's kernel file,
...
Do you want to relink the kernel now? y
...
Do you want this kernel to boot by default? (y/n) y
...
Do you want the kernel environment rebuilt? (y/n) y
...
13. Reboot the Unix system to initialize the driver fuction.
# reboot
TRADEMARKS
==========
All Tademarks or Brand names mentioned are properties of
their respective companies.
== End of File ==
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.