WIN95.TXT Driver File Contents (en1207c.zip)

.TOPIC:
Contents

              Accton Technology Corporation
        NDIS/3 DRIVER FOR WINDOWS 95 INSTALLATION
 ==========================================================

  Copyright (c) 1995, 1997 by Accton Technology
  Corporation. All rights reserved.


  Contents:
  ---------

           A) Install NDIS 3.1 driver to the Windows 95
           B) Configure NDIS 3.1 driver to the Windows 95

A) Install NDIS 3.1 driver to the Windows 95
    The drivers named ACCPCI.SYS contained in the directory
    WIN95.


    NDIS Driver Installation on Windows 95
    --------------------------------------
    1. Plug Accton's EN1203 or EN1207(-TX/B-TX/C-TX) series adapter into one of
       the Master PCI slots of your PCI platform.
    2. Turn power on then boot from Windows 95.
    3. Windows 95 will find and bind the DECchip 21x40 driver supported by
       itself, then configure your network environment.
    4. After step 3., do not restart Windows 95; instead run the Accton
       Windows 95 driver installation program SET95.EXE. (SET95.EXE is
       located in the root directory of the Diskette Release)
    5. In the SET95 program, click "Yes" to continue installation.
    6. The system restart automatically.
    7. Windows 95 will prompt with PCI Ethernet Controller in New Hardware Found
       dialog box.
    8. Select "Driver from disk provided by hardware manufacturer" from New
       Hardware Found dialog box, then click OK button.
    9. Insert the Accton Driver Diskette in your floppy drive.
   10. Enter the driver pathname, i.e. A:\ (or B:\), then click the OK
       button in the Install from Disk dialog box.
   11. Follow screen instructions to complete the process.
   12. Restart your computer.



B) Configure NDIS 3.1 driver to the Windows 95

    1. Click the "My Computer" icon in the Main Program Group.
    2. Click the "Control Panel" icon in My Computer window.
    3. Click the "Network" icon in the Control Panel window.
    4. Select "Adapter" item from Network Component Type dialog box,
       then click the "Properties..." button.
    5. Click "Advanced" button in Properties for Accton EN120x PCI Ethernet
       Adapter dialog box.
    6. Here, you can set the following properties:

       <1>. Burst Length : 1 Dword        ; Default is 16 Dwords.
                           2 Dwords       ; (1 Dword = 4 bytes).
                           4 Dwords
                           8 Dwords
                          16 Dwords
                          32 Dwords

       <2>. Connection Type (32-bit driver): <NDIS3 driver>
             for EN1203 adapter:                ; Default is AutoDetect
                              AutoDetect
                              BNC (10Base2)
                              TP  Full_Duplex
                              TP  No_Link_Test
                              Twisted Pair (10BaseT)

             for EN1207(-TX/B-TX/C-TX) Series adapter      ; Default is
AutoSense                               100BaseTx
                              100BaseTx Full_Duplex
                              10BaseT
                              10BaseT Full_Duplex
                              AutoSense
                              BNC (10Base2)    ; supports only EN1207 adapter

       <3>. Connection Type (16-bit driver): <NDIS2 driver>
            (This argument will be put in MAC driver section in PROTOCOL.INI)

                              Auto Detection    ; Default is Auto Detection
                              Twisted Pair
                              TP Full Duplex
                              BNC (Thinnet), (10Base2)

       <4>. Receive Buffers : 8, 16, 32, 48, 64.
                              default is 16.

       <5>. Map Registers   : 4, 8,
                              default is 8.
                              This parameter depends on the specific machine,
                              for x86, the value is 8.

       The following three parameters are  used for EN1207(-TX/B-TX/C-TX)
       adapter only.

       <6>. Store And Forward : Enabled --> Enable early transmit,
                                Disabled--> Disable early transmit,
                                default is Disabled.

       <7>. Transmit Threshold : the transmit FIFO threshold level when Store and
                                 Forward is disabled.

                             10Mbps:  72,  96, 128, 160   bytes,
                            100Mbps: 128, 256, 512, 1024  bytes,
                            default is 160 or 1024 bytes.

       <8>. Data Rate-16 bit driver: the line speed of EN1207(-TX/B-TX/C-TX)
            adapter,

                                     Valid data: 10Mbps, 100Mbps,
                                     default is 100Mbps.

    7. Follow screen instructions to complete the process.

    8. Restart your computer.



---End of File---

Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web3, load: 1.58