Accton Technology Corporation
NDIS/2 Driver Installation for EN1203, EN1207(-TX) Series Ethernet Adapter
===================================================================
Copyright (c) 1995-1997 by Accton Technology Corporation.
All rights reserved.
The driver you need are in the directories MSLANMAN.DOS, MSLANMAN.OS2 and
NDIS. The NDIS drivers contained in these subdirectories are used with 3Com
3+Open, Microsoft OS/2 LAN Manager OEM distribution, Release 1.x or 2.x,
and other compatible OEM versions of LAN Manager. The driver can also used
with IBM LAN Server 3.0, 4.0, Banyan VINES, ARTISOFT LANtastic 5.0, 6.0,
Wollongong Pathway Access, Microsoft Windows for Workgroups v3.11,
DEC PATHWORKS, Sun PC-NFS etc.
The drivers named ETHPCI conform to the Network Driver Interface Specification
(NDIS) defined by Microsoft/3Com.
Included in MSLANMAN.DOS, and NDIS subdirectories are the following files:
\MSLANMAN.DOS\DRIVERS\ACCTON\ETHPCI
ETHPCI.DOS The DOS NDIS MAC driver
PROTOCOL.INI A sample section of PROTOCOL.INI file
\MSLANMAN.DOS\DRIVERS\NIF\
ETHPCI.NIF Network Information File
\MSLANMAN.OS2\DRIVERS\ACCTON\ETHPCI
ETHPCI.OS2 The OS2 NDIS MAC driver
PROTOCOL.INI A sample section of PROTOCOL.INI file
\MSLANMAN.OS2\DRIVERS\NIF\
ETHPCI.NIF Network Information File
\NDIS
NDIS.TXT This readme file
WFW.TXT The Installation guide for
Windows for Workgroups v3.11
LANMAN.TXT The Installation guide for
LAN Manager
LANSVR.TXT The Installation guide for Lan Server
BANYAN.TXT The Installation guide for Banyan VINES
LANTASTI.TXT The Installation guide for ARTISOFT LANtastic 5.0, 6.0
PATHWORK.TXT The Installation guide for DEC PATHWORKS
PCNFS.TXT The Installation guide for Sun PC-NFS
\NDIS\DOS
EN120XD.NIF Network Information File for IBM Lan Support Program
ETHPCI.DOS The DOS NDIS/2 MAC driver
OEMSETUP.INF Network Information File for Windows for Workgroups
v3.11
PROTOCOL.INI A sample section of PROTOCOL.INI file
\NDIS\OS2
EN120XO.NIF Network Information File for IBM LAN Server 3.0, 4.0
ETHPCI.OS2 The OS2 NDIS/2 MAC driver
PROTOCOL.INI A sample section of PROTOCOL.INI file
Sample PROTOCOL.INI Files and Parameters
----------------------------------------
[ETHPCI_NIF]
DriverName = ETHPCI$
; Slot = 1 ;; {1-16}
; SIA_Mode = AUTODETECT
; {SIA_Mode = TP, BNC, TP_FULL_DUPLEX, AUTODETECT}
; DATA_RATE = MB10 ;; {MB10, MB100}
There are several parameters included in the ETHPCI_NIF section of the
PROTOCOL.INI file. However, the only parameter that you should specify
is the "drivername."
If you change other parameter settings, such as the SIA_MODE, make sure
that it matches the hardware setting. Otherwise, the adapter may fail.
If you don't specify these settings, Accton's NDIS/2 driver
will automatically detect them.
SLOT Specifies which network adapter is used by the driver. If you
have only one Accton's PCI LAN card in your machine, this parameter
is unnecessary! For two or more Accton's PCI LAN cards, this
parameter is required and cannot be omitted from PROTOCOL.INI.
For the first EN1203 or EN1207(-TX) adapter, Slot=1, and
the second one, Slot=2, third, Slot=3,..., etc.
SIA_MODE Specifies the medium type used by the adapter.
Acceptable values for this parameter are AUTODETECT, TP, BNC
and TP_FULL_DUPLEX. If you didn't specify this settings it
would be AUTODETECT for both EN1203 and EN1207(-TX).
DATA_RATE Specifies the line speed for EN1207(-TX), default is MB100.
MB100: 100Mbps, MB10: 10Mbps
Note! Do not use this setting for EN1203 adapter.
TX_THRESHOLD
Specifies the FIFO threshold level during packet transmittion.
Acceptable values for this parameter are
Level (bytes) Support Suppot
Keywords EN1203, EN1207(-TX) EN1203 EN1207(-TX)
======== ================== ======= ===========
LW128 72 128 Yes Yes
LW256 96 256 Yes Yes
LW512 128 512 Yes Yes
LW1024 160 1024 Yes Yes
FP X full packet No Yes
-- END of File--
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.