.TOPIC: Contents ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ ACCTON TECHNOLOGY CORPORATION ³ ³ EN1203, EN1207(-TX) Series PCI-BUS (FAST) ETHERNET ADAPTER ³ ³ NDIS/2 DRIVER FOR LAN SERVER INSTALLATION ³ ³ ³ ³ Copyright 1995-1997 ACCTON Technology Corporation ³ ³ All rights reserved. ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ The driver named ETHPCI contain in the directory NDIS conforms to the Network Driver Interface Specification (NDIS) defined by Microsoft/3Com. Content of the file: A.) DOS LAN Requester Installation for LSP V1.30 to V1.37 B.) LAN Server 4.0 DOS Client Installation C.) OS/2 LAN Server 3.0 Installation D.) OS/2 LAN Server 4.0 Installation E.) OS/2 LAN Server 4.0 Installation (Multiple LAN Adapters) A.) DOS LAN Requester Installation for LSP V1.30 to V1.37 ========================================================= 1. Insert the IBM LAN Support Program (LSP) Version 1.30 (or 1.31 to 1.37) Diskette into your floppy drive (drive A: or B:). 2. Type the following from your DOS prompt and press <Enter>: A:>dxmaid 3. The screen will display the IBM logo. Press <Enter> twice until the "Environment Information" appears onscreen. 4. Responds to the screen prompts, specifying the following values for each field: Use the <Space Bar> to toggle between choices: Configuration for this computer? Yes Use existing configuration information? Yes Do you have adapter option diskettes? Yes Are you configuring for two adapters? No Do you need 802.2 interface support? No Type change as needed to drive and directory information below: Source for LSP A:\ Target for new configuration C:\lsp 5. Make sure that the values given above are correct. Press <Enter> to store your choices. 6. Insert the Driver Diskette in your source drive. Specify the path and press <Enter> to proceed. Examples: A:\NDIS\DOS, B:\NDIS\DOS 7. Upon pressing <Enter> the necessary drives from the Driver Diskette are copied onto you target directory in the hard disk. 8. Follow screen instructions to complete the process. Simply pressing <Enter> for each screen display will select the default options. Press <Enter> three times, until you reach the display prompting you to insert the LSP diskette. 9. Insert the LSP diskette as prompted. Press <Enter> to acknowledge completion of the action. 10. A screen showing the current configuration detected will be displayed. It should show the Accton EN1203, EN1207 PCI Series Ethernet adapter and the protocols already selected (i.e., "IBM IEEE 802.2" and "IBM OS/2 NETBIOS"). 11. Press <F4> to save the new configuration. This completes the LSP installation. ************************************************************ * NOTE: * * * * You should have defined in your CONFIG.SYS the * * minimum of 20 files, i.e. FILES=20, to run the * * software properly. Change the FILES line using * * the text editor if needed. * * * * If installing LSP for the first time, you should * * complete the installation by typing install and * * following the further instructions on screen. * ************************************************************ 12. Use a text editor to edit the CONFIG.SYS file. Specify at least 20 file in the FILES= line. Modify it to the following: FILES=20 13. Save the configuration and reset your computer. 14. Insert the DOS LAN Requester Install Diskette into your floppy drive. 15. Type the following and press <Enter>: INSTALL <Enter> 16. The IBM logo will again appear on the screen. Press <Enter> to move on to the next screen. 17. Follow screen instructions, pressing <Enter> to move from screen-to-screen until you are prompted to indicate the pathname of the DOS LAN Requester directory. TIP: After the IBM logo appears on the screen, press <Enter> twice to reach this screen. 18. Specify the pathname for the DOS LAN Requester directory (C:\DOSLAN is the default). Then press <Enter> to continue. 19. The program will ask you for the services that you require. 20. Highlight the appropriate option. Select either "Send messages" or "Send, View, Edit, and Log message" option. TIP: Normally, second option "Send, View, Edit and Log message" is selected. 21. Specify the PC's ID and domain ID. The domain ID is the domain server ID; it should be the same for all workstations of the network. 22. Follow screen prompts to complete the installation. B.) LAN Server 4.0 DOS Client Installation ========================================== 1. Under DOS environment, change directory to the LAN Server DOS Client subdirectory, that is, enter the following command CD \NET Note: \NET is the default directory name of LAN Server 4.0 DOS Client. Note: Before installation the LAN driver, you should install IBM LAN Server DOS Client first. 2. Type INSTALL and press <Enter> to enter the DOS LAN installation program. 3. When the "Install for DOS LAN Services" screen appears, highlight the "the listed options are correct" choice and press <Enter>. 4. On the second screen, you will see the following information: Machine ID, User name, Domain name,... and Network card information. Highlight the "Network card : No network card was selected" choice and press <Enter>. 5. Select the first choice from the following two selections "Add driver for network card", "Driver configuration is correct". 6. Select "Network card not shown in list below ..." from a listing of network adapters on the next screen. 7. Insert the Accton EN1203, EN1207(-TX) driver diskette into driver A: and specify the path of driver installation file (OEMSETUP.INF) by typing A:\DOS and press <Enter>. 8. Highlight "Accton EN1203, EN1207 PCI Series LAN Adapter" and press <Enter>. 9. If necessary, choose "Edit settings for network card driver", otherwise choose "Driver configuration is correct". Note: Please see NDIS.TXT for the parameter settings. 10. Highlight "The listed options are correct" and press <Enter> on the next screen. 11. Then, the Installation Program will ask you to insert the DOS LAN Services Disk 1. Be careful, do not following the screen instruction here, that is, you should not insert the DOS LAN Services Disk. All you have to do is press <Enter> and wait for installation complete. 12. Remove the diskette from driver A: and press <Enter> to restart the machine. C.) OS/2 LAN Server 3.0 Installation ==================================== 1. Copy ETHPCI.OS2 and EN120XO.NIF files from your Driver diskette (A:\NDIS\OS2) to C:\IBMCOM\MACS. 2. Click the OS/2 LAN Service icon. 3. Select "Installation and configuration." The IBM logo should appear onscreen. 4. Click <OK>. 5. Select <Advance> and press <Enter>. 6. Select "Install or Configuration this Workstation." 7. Select server type, adding a server or domain controller. The "install or remove" selections should appear. 8. Select "Configure a component." 9. Click the "Configure" button. 10. Select "Configure workstation." 11. Select "Accton EN1203, EN1207 PCI Series Ethernet Adapter" when prompted to identify you Network Adapter, Then click the <Add> button. 12. Select "802.2" from the list and click the <Add> button. 13. Select IBM NETBIOS from the list and click the <Add> button. 14. Select <OK> to confirm all selections. 15. Follow screen instructions to complete the process, selecting <OK> to accept default selections. 16. Continue pressing <OK> until your screen prompts you to backup old CONFIG.SYS and AUTOEXEC.BAT and create a new CONFIG.SYS and AUTOEXEC.BAT. Also select <OK> to confirm this. 17. Installation is complete now. Reset your PC by turning it off and on. D.) OS/2 LAN Server 4.0 Installation ==================================== 1. In OS2 desktop, click the MPTS(Multi-Protocol Transport Service) icon. The IBM logo should appear on screen. 2. Click the <OK> button. 3. Click the <Configure> button. 4. Select the "LAN adapters and protocols" item, then click <Configure> button. 5. Click <Other adapters...> button. 6. Insert Accton EN1207-TX PCI Ethernet Adapter Driver Diskette into a specified drive (A: or B:), then enter the driver path like A:\NDIS\OS2, (or B:\NDIS\OS2, etc.) and click <OK> button 7. Select "Accton EN1203, EN1207 PCI Series Ethernet Adapter" from Network Adapters list when prompted to identify you Network Adapter. Then click the <Add> button. 8. Select "IBM 802.2" from the Protocols list and click the <Add> button. 9. Select "IBM OS2 NETBIOS" from the Protocols list and click the <Add> button 10. Select "IBM Netware Requester Support" from the Protocols list and click the <Add> button if you need to logon NETWARE server. 11. Select <OK> to confirm all selections. 12. Click <Close> button in the Configure window. 13. Click <Exit> button in the MPTS window. 14. Click <Exit> button, then your screen will prompts you to backup old CONFIG.SYS and AUTOEXEC.BAT and create a new CONFIG.SYS and AUTOEXEC.BAT. Also select <OK> to confirm this. 15. Installation is complete now. Reset your PC by turning it off and on. E.) OS/2 LAN Server 4.0 Installation (Multiple LAN Adapters) ============================================================ For multiple adapters installation, you must do the follows: a. configure <LAN Services> b. configure <MPTS> a. Configure <LAN Services> ------------------------------ 1. From OS/2 desktop, click <LAN Services> 2. In LAN Services windows, click <OS/2 LAN Services Installation/Configuratin> 3. click <OK> when the IBM logo appears. 4. In "Basic or Advanced Installation/Configuration" dialog box, click <Advanced> 5. Select "Install or configure this workstation" in "Installation Tasks" dialog box, and click <OK> 6. Select Server Type (like, Domain controller) then click <OK> 7. Select "Configure a component" from "Installation and Configuration" dialog box, and click <OK> 8. Select "LAN Services Adapters" from "Configure" dialog box, and click <Configure...> 9. Select the LAN adapters to be used by LAN Services (for 2 adapters, select Adapter 0, Adapter 1 ) and click <OK> 10.Assign the NETBIOS Resources like Sessions, Commands & Names (you can use the default value) and click <OK> for different adapters. 11.Click <OK> from "Configure" dialog box. 12.Select "Apply the changes" and click <OK> from "Installation and Configuration" dialog box. 13.Follow screen instructions to complete the installation. 14.Shut down and reboot the machine. b. Configure <MPTS> ---------------------------------- If you have more than one adapter, you need to configure each of them for different Slots by clicking <Edit> in "Configure" windows. ******************************************************************** * NOTE!! * * * * Each slot represents an PCI adapter index value for one * * adapter installed (EN1203 or EN1207(-TX) in this case) * * assigned by the PCI-BIOS. For example, if the 1st slot is * * assigned slot=1, then the next slot will be assigned * * slot=2, the third slot=3 and so forth until the last slot * * * ******************************************************************** ------------------------------------------------------ All trademarks or brand names mentioned are properties of their respective companies. ===End of File===Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.