Dear customer,
----------------------------------------------------------------------------
(A) Plug & Play Utility (Optional for Plug & Play Modem)
The SETMODEM program is provided to allow your 56Kbps Plug and Play
modems to be configured on PCs which have not been configured to support Plug
and Play. PCs that have Windows 95 do not need the SETMODEM program since
Windows 95 supports Plug and Play.
SETMODEM is a DOS utility and will:
1) look for an ISA Plug and Play modem with a valid Vendor ID
2) find an available COM port
3) display the recommended COM port and allow the user to either agree
with the recommended COM port or to select a different COM port
(COM can have an IRQ of 3/4/5/7 and I/O base of 3F8/2F8/3E8/2E8/100/
108/240)
4) exit the program after configuring the Plug and Play modem
5) before exiting, write a batch file line in autoexec.bat so that the
Plug and play modem will automatically be configured on the next power
up
6) Run INSTALL.EXE for the first time installation of SETMODEM utility.
Note: This utility will not recommend COM1-4 even if available if Cardmanager
PCMCIA software is installed on the system. If Cardmanager is disabled
(comment out the proper lines in config.sys), then COM1-4 will be recommended
if available.
------------------------------------------------------------------------------
(B) Windows 95 Modem Driver File
The Win95drv.inf file is a driver file for Windows 95. This file is used
for modem installation in Windows 95. In Windows 95, the PnP modem will be
found automatically. Then Windows 95 will query you for the driver used by this
modem. Insert your driver diskette and select the suitable modem type.
If your modem does not support Plug & Play mode, do the following steps:
(1) Make sure the commport of the modem does not conflict with
other hardware in your PC system.
(2) Boot up the Windows 95 and click the Modem icon inside the
Control Panel to install your modem.
(3) Click "Next" to run the "Add New Hardware Wizard". Then
Windows 95 will look for your new hardware.
(4) After the "detection Progress" finish, Windows 95 will find
your new communication port.
(5) Then click "Finish" bar to continue install the modem.
(6) Click "Next" bar in the "Install New Modem" display to let
Windows 95 to scan your modem type.
(7) Insert the driver diskette and click the "Have Disk" bar to
select the correct modem type.
(8) Now, you can install the bundle software to optimize your
modem features.
********* Select the correct type for your modem card.
(select "HighTech" 's model)
********* The best way to do the installation or to fine tune the
commports and modem settings, please refer to your User Guide
of Windows 95.
-------------------------------------------------------------------------------
(C) Windows 95 Serial Wave Driver File
The Ser_wave.inf file is a Serial Wave driver file for windows 95. If your
Windows 95 has been installed the "Unimodem V" function. Then this file will be
required by Windows 95 after you installed the modem driver Win95drv.inf .
Unimodem V is a special function for Windows 95.For detail informations, Please
contact Microsoft.
-------------------------------------------------------------------------------
(D) Downloadable Firmware (Upgrade Firmware Version)
There are two methods to download the new firmware into the Flash ROM.
We suggest users to use the method (i) to upgrade the firmware.
(i) Run the program FlashCom.exe Utility(Simple & Easy method)
(1) Run the FlashCom.exe
(2) The program will detect your 56kbps modem comport
(3) Click the "LOAD NOW" bar after the modem detected.
(4) Then your Flash ROM will be programmed with a new firmware.
(5) Closed the Utility after successfully programmed
For detailed information, refer to the help file of FlashCom utility!
(ii)Run the AT command-- AT** (Advanced method)
AT** Command--Download to Flash Memory
The linear flash memory downloader in the modem firmware allows flash
memory connected to the modem external memory bus to be upgraded with the
revised modem firmware. The process transfers (uploads) the upgraded modem
firmware (data) from the host computer to the modem which transfer (down-
loads) the data to the flash memory device. Note that this downloader
function must be provided in modem MCU firmware initially installed in
external flash memory, i.e., the downloader does not support the programming
of blank flash memory.
Programming the flash memory device is a two-step process.
(1) When the AT** command is issued, the modem firmware boot loader is
invoked and the user will first load a flash load module(FLM) into
the modem's RAM. The FLM contains the programming algorithm for the
flash memory device being programmed and any messages that may be sent
during the load process.
(2) The user will then load the new modem firmware which the FLM will then
program into the flash memory device.
Procedure:
(1) Install in the modem flash memory programmed with the modem firmware;
ensure that the flash memory device is programmed with the sector
secure mode to UNSECURE (AMD only), otherwise the device cannot be
re-programmed in the modem.
(2) Put the FLM file and the new modem firmware file (e.g., V1120dp.S37)
in a appropriate directory on the computer's hard disk.
(3) Configure the communications application program for a DTE rate be-
tween 9600bps and 57600bps (57600bps is faster) and RTS/CTS flow con-
trol. A load at 57600bps will take approximately 2 minutes; a load at
19200bps will take approximately 6 minutes.
(4) Check the modem for response by typing AT.
(5) Initiate the download process using the AT**n command, where:
AT** or AT**0 Download speed is the last sensed speed
(recommended command)
AT**1 Download speed is 38.4kbps.
AT**2 Download speed is 57.6kbps.
The "Download Initiated" message appears upon issuing the AT**n command.
(6) Perform an ASCII upload of the FLM file (e.g., BPFLV47.S37) from the
host computer to the modem RAM using an industry standard communications
software or equivalent process (ensure that all ASCII tranlation or
pacing is turned off).
To abort the load at this point, wait for the FLM download process to
time out, send a bad S37 record, or reset the modem. If the load process
times out, the modem must be reset (ATZ) before the FLM can be loaded
again.
(7) After the FLM has been loaded, perform an ASCII upload of the new modem
firmware hex file(e.g., V1120dp.S37) from the host computer to the modem
RAM using an industry standard communication software or an equivalent
process.There will be a 3-second pause after the first recordof the
V1120dp.S37 file is sent, which is the FLASH erase cycle. There is no
turning back at this point.
If the flash download fails (because of a bad .S37 record for example)
or the upload is aborted, as long as the modem is not turned off or
reset, it will remain in the flash load cycle and the upload can be re-
attempted at step 7.
A "Worng Device"message is displayed if an incorrect FLM is used. In
this case, restart at step 5 and upload the correct FLM file.
A "Wrong Hex File or flow control" message is displayed if an incom-
patible hex file format is used(non-Motorola S37 format) or if the DTE
igores flow control( the flash download uses both Xon/Xoff and RTS/CTS
flow control). If the wrong format was used, reinitiate the upload at
step 7 using a correct firmware hex file.
(8) A "Device successfully programmed" message is displayed by FLM at the
completion of a successful download and the modem must do a cold start.
-------------------------------------------------------------------------------
(E) Special Feature Command---AudioSpan Commands.
***User can use the AudioSpan(SVD) feature through the software BitWare ******
(i) AT-SMS=x,y,z,t -- Select AudioSpan/DSVD Mode
x:AudioSpan/DSVD/Data mode select and automatic mode select enable
0 = Data mode
1 = DSVD mode (Modem not supporting DSVD will respond ERROR)
2 = AudioSpan mode (Modem not supporting, will report ERROR)
3 = Automatic mode (DSVD/AudioSpan/Data) (Default)
Note:AT-SMS=1 performs the same operation at AT-SSE=1
y:Minimum data speed(bps) with audio for AudioSpan mode
z:Maximum data speed(bps) with audio for AudioSpan mode
y,z Value V.61 ML144 ML288
4800 S(y,z Default) S(y Default) S(y Default)
7200 - S S
9600 - S(z Default) S
12000 - - S
14400 - - S(z Default)
S=Supported.
- =Not Supported.
t:Symbol rate (ML288 modeulation only)
0 = Auto Selection (Default)
1-6 = Reserved
Notes
AudioSpan audio quality is dependent upon modulation mode, data rate and tele-
phone line quality. Some guidelines are :
1. Higher quality telephone lines provide better audio quality than im-
paired lines.
2. A lower data speed with audio provides better audio quality than higher
data speed with audio. For example, a ML288/9600 connection will be
audibly superior to a ML288/14400 connection.
3. For identical data speed with audio using different modulations (e.g.,
ML144 vs ML288), the audio quality at ML288 will be superior.
Examples
1. AT-SMS=2 select AudioSpan Mode (y,z,and t are not required)
2. AT-SMS=2,4800,9600 select AudioSpan Mode,Min. data speed with audio of
4800bps, and Max. data speed of 9600bps.
------------------------------------------------------------------------------
(ii) AT#VLS=x --Voice Line Select
0 = Telephone handset (Default)
6 = Speakerphone
The AT#VLS settings must be issued prior to establishing AudioSpan connection
if a voice line other than the default telephone handset is desired.
------------------------------------------------------------------------------
(iii) AT-SQS= x,y --Select AudioSpan Modulation.
x:Select modulation mode.
0 = V.61
1 = ML144
2 = ML288 (Default)
y:Enable/disable AudioSpan automatic modulation (automode) selection
0 = Disable AudioSpan automodulation
1 = Enable AudioSpan automodulation
Note:The AT-SQS parameters should remain at default unless a parti-
cular modulation is perferred.
Examples
1. AT-SQS=2,1 enables AudioSpan automodulation starting with ML288.
2. AT-SQS=2,0 disable AudioSpan automodulation and selects ML288.
3. AT-SQS=1,0 disable AudioSpan automodulation and select ML144.
------------------------------------------------------------------------------
(iv) AT-SMC=x --Enable/Disable ML144 Data Burst
0 = Disable data burst
1 = Enable data burst (Default)
ML144 data burst can be enabled using the -SMC command in ML144 modulation.
Data burst will keep the audio channel open only when enery is detected on the
handset.When silence is detected in data burst mode, the connected modems will
upshift in speed for higher throughput.
Example : Switch from normal handset conversation to AudioSpan data connection
between AudioSpan modems. The both orignated and answer DTE are set to
115200bps.
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³Orignate (Call Mode) ³ Answer (Answer Mode) ³ ³ ³
ÃÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Key-in ³ Display Respond ³ Key-in ³Display Respond³ Comments ³
ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ ³ ³ ³ ³ Users establish³
³ ³ ³ ³ ³ handhset³
³ ³ ³ ³ ³ conversation and³
³ ³ ³ ³ ³ both handsets are³
³ ³ ³ ³ ³ off-hook.³
ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ AT&F ³ ³ AT&F ³ ³ Reset modems³
ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ ³ OK ³ ³ OK ³ ³
ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ AT-SMS=2 ³ ³ AT-SMS=2³ ³ Enable AudioSpan³
³ ³ ³ ³ ³with default settings³
ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ ³ OK ³ ³ OK ³ ³
ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ ATD ³ ³ ³ ³ Originate modem³
³ ³ ³ ³ ³ initiates data³
³ ³ ³ ³ ³ negotiation but will³
³ ³ ³ ³ ³ not actually dial³
³ ³ ³ ³ ³ since the handset is³
³ ³ ³ ³ ³ already oofhook.³
ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ ³ ³ ATA ³ ³ Answer modem detects³
³ ³ ³ ³ ³ negotiation sequence³
³ ³ ³ ³ ³ and reports RING. ³
ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ ³ CONNECT 115200 ³ ³ CONNECT 115200³ AudioSpan is³
³ ³ ³ ³ ³ established and³
³ ³ ³ ³ ³ users can resume³
³ ³ ³ ³ ³ conversation. The³
³ ³ ³ ³ ³ connect message³
³ ³ ³ ³ ³ represents the DTE³
³ ³ ³ ³ ³ speed on each side.³
ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ <data> ³ ³ <data> ³ ³ Modem exchange data ³
ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ ³ ³ +++ ³ ³ Answer modem³
³ ³ ³ ³ ³ enters command³
³ ³ ³ ³ ³ mode to prepare for³
³ ³ ³ ³ ³ disconnect.³
ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ ³ ³ ³ OK ³ ³
ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ ³ ³ ATH ³ ³ ³
ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ ³ NO CARRIER ³ ³ NO CARRIER ³ Modems disconnect³
³ ³ ³ ³ ³ in AudioSpan mode³
³ ³ ³ ³ ³but handset are still³
³ ³ ³ ³ ³ off hook and³
³ ³ ³ ³ ³ conversation can³
³ ³ ³ ³ ³ continue.³
³ ³ ³ ³ ³ Conversation is³
³ ³ ³ ³ ³ terminated when³
³ ³ ³ ³ ³ both handsets are³
³ ³ ³ ³ ³ hung up.³
ÀÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
Note : the transition from handset conversation to AudioSpan mode can take up
to 8 seconds. The handsets will be silenced during negoitation period.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.