Multi-Tech Windows 2000 Driver for Family of ISI adapters
Contents
--------
- Introduction
- Hardware Description
- Getting Started and Installation Procedures
- ISI PCI card Installation procedures
- ISI ISA card Installation procedures
- Web and Telnet Management software installation procedures
- Windows 2000 modem installation procedures
- To manage ISI cards using a Web Browser
- To manage ISI cards using a Telnet client
- Flashing new ISDN-TA or Modem firmware via Web browser
- To remove ISI driver
- To remove ISI Management software
- Revision History
- ISI Modem and Hybrid Ports Information
- ISA card Dip Switch and Jumper settings
- Support Options
- Copyrights and Trademarks
Introduction
------------
To help your friendly installation, you can check it from the
REAMDE.TXT files. Should there be any further recommendations,
please contact with the Local Multi-Tech Systems office listed as below.
In this document "ISI card" refers to Intelligent-Serial-Interface(ISI)
cards available from Multi-Tech Systems, Inc. For example it can be:
For ISA cards:
ISI4608-ISA, ISI3334-ISA and ISIHI-2S/2U
For PCI cards:
ISI4608-PCI, ISI5634-PCI and ISIHP-2S/2U/4S/4U
Hardware Description :
----------------------
ISA Hardware description :
--------------------------
1) Each ISA card occupies 16 bytes of I/O address on the PC. The address
can start on any 16th address boundary (eg. 100 hex, 110 hex, 120 hex etc.)
The addresses on the ISI are switch selectable. Please refer to
the table below for some sample addresses. Valid I/O addresses are
multiples of 16 starting from 100 hex ending at 3F0 hex.
2) Each ISI ISA card also interrupts the PC by using an interrupt line
(IRQ). The IRQ on the card are jumper selectable. You can choose IRQs
2,3,4,5,7,10,11,12,15.
3) Each ISI requires a unique I/O Address space and a unique interrupt
vector.
PCI Hardware description :
--------------------------
1) ISI PCI card also occupies 16 bytes of I/O address on the PC. The
address are 16bit wide. The address are AUTO assign by the BIOS when
the PC boots up.
2) ISI PCI card also interrupts the PC by using an interrupt line (IRQ).
The IRQ on the card are AUTO assign by the BIOS when the PC boots up
3) Each ISI PCI will get assign a unique I/O Address space and a unique
interrupt vector by the BIOS. But in some cases the BIOS will assign
the same IRQ for two or more ISI PCI cards and this should be ok.
Getting Started and Installation Procedures:
--------------------------------------------
ISI PCI card Installation procedures:
-------------------------------------
1) install PCI card into one of the empty PCI slot
2) power up Windows 2000
3) When Windows 2000 comes up, it will auto detected PCI card and bring
up the New Hardware Wizard
4) in the New Hardware Wizard, click Next
5) check button Search for a suitable driver and click Next
6) check button Specify a location and click Next
7) specify A:\ and click OK or specify the location where the driver located
8) specify A:\ if ask again or specify the location where the driver located
9) click Finish when installation is done
ISI ISA card Installation procedures:
-------------------------------------
1) install ISA card into one of the empty ISA slot
2) power up Windows 2000
3) bring up the Control Panel
4) click Add/Remove Hardware and click Next
5) check Add/Troubleshoot a device and click Next
6) select Add a new device and click Next
7) select NO, I want to select the hardware from the list and click Next
8) select Multi-port serial adapters and click Next
9) click Have Disk and enter path A:\ and click OK
10) select ISI4608-ISA 4 ports or 8 ports and click Next
11) enter the IOaddress and IRQ and click OK and click Next
12) click Finish
Web and Telnet Management software installation procedures:
-----------------------------------------------------------
1) Run Setup.exe from the management diskette
2) after software installed, it will prompt to restart the server,
click YES to restart the server
Windows 2000 modem installation procedures:
-------------------------------------------
Assuming the driver is installed and all the com ports are created
1) bring up Control Panel
2) click Phone and Modem options
3) select Modems tab (at the top) and click Add
4) check Don't detect my modem and click Next
5) select the proper Multi-Tech modem configuration and click Next
(check the ISI Modems and Hybrid Ports Information section. Make
sure ports are mapped properly with proper modem discription)
6) map the modem to all the ISI ports
7) click Finish
To manage ISI cards using a Web Browser:
----------------------------------------
Local management:
1) bring up Internet Explore locally
2) specify URL as "http://127.0.0.1:88"
3) login as administrator
Remote management:
1) bring up a web browser remotely
2) specify "http://ip_address:88", ip_address is the address for the
Windows 2000 server that has the ISI cards installed
3) login as administrator
Configure the ISI Web server services:
1) bring up Control Panel
2) click Administrative Tools
3) click Internet Services Manager
4) select ISIWeb, click Action and click Properties
To manage ISI cards using a Telnet client:
------------------------------------------
In order to use a standard third parties telnet client, you must set NTLM
authentication to except clear text:
1) bring up Control Panel
2) click Administrative Tools
3) click Telnet Server Administration
4) select option 3, Display / Change Registry settings
5) select option 7, NTLM
6) change value from 2 to 1
7) exit out of all the menus
Check and make sure Telnet server service is running:
1) bring up Control Panel
2) click Administrative Tools
3) click Services
4) look for Telnet service and make sure it is running, if not start the
service
Local management:
1) bring up local telnet client
2) specify "open 127.0.0.1"
3) at the C: prompt, type in "isitelnet"
Remote management:
1) bring up local telnet client
2) specify "open ip_address", ip_address is the address for the
Windows 2000 server that has the ISI cards installed
3) login as administrator
4) at the C: prompt, type in "isitelnet"
Flashing new ISDN-TA or Modem firmware via Web browser:
-------------------------------------------------------
MAKE SURE you have MSVCP60.DLL in C:\WINNT\SYSTEM32 directory
1) put the new firmware (hex file) into C:\WINNT\SYSTEM32\ISIMGMT directory
2) bring up the Web browser and enter URL for the ISI cards
3) login as administrator when prompt
4) click the ISI card number under the Card Number column
5) check the ports you want to upgrade firmware in the Port Selection column
(for ISIHI/HP-2S/2U cards, you only need to select 1 and 3 for ISDN TA firmware)
(for ISIHP-4S/4U cards, you only need to select 1,3,5 and 7 for ISDN TA firmware)
6) click "Flash Modem on Selected Ports" button on the bottom screen
7) enter the Hex file name (name of the file in step 1)
8) select the appropreate device type base on ports on the ISI card
(ISI3334 for modem on ISI3334 ISA card)
(ISI5634PCI for modem on ISI5634 PCI card)
(ISIHP_MODEM for modem on ISIHI/HP-2S/2U/4S/4U card)
(ISIHI-TA for ISDN on ISIHI-2S/2U card)
(ISIHP-TA for ISDN on ISIHP-2S/2U/4S/4U card)
9) you can change the baud rate at 115200 or leave it at 19200 default
10) click "Flash Modems" button
11) while flashing you will see the message "Flashing" on the Connect
Status column, if you don't see this, then you need to go back and
make sure all the above steps are done properly
To remove ISI driver:
---------------------
1) bring up Control Panel
2) click Add/Remove hardware and click Next
3) check Uninstall/Unplug a device and click Next
4) check Uninstall a device and click Next
5) select Multi-Tech ISI card and click Next
6) check Yes, I want to uninstall this device and click on Next
7) click Finish
To remove ISI Management software:
----------------------------------
1) bring up Control Panel
2) click Add/Remove Program
3) Select ISI Management and click Change/Remove
Revisions History
-----------------
Version 2.0.0
-------------
- include Microsoft CAT file for Digital Signatures
Version 1.4.0
-------------
- Fixed serial device enumeration problem
- include new ISI4608.BIN and ISI4616.BIN (ppp delimiter off)
- updated modem and ISDN INF files
- isicom.sys shows Multi-Tech name when doing file properties
Version 1.30
Features on Web and Telnet Management:
--------------------------------------
- using standard Web browser and Telnet clients
- local and remote management
- port statistics
- keep track of number of calls and duration of each call
- keep log files for a specified time period
- send email alerts based on certain events
- reset individual port without affect others
- update ISDN/TA and modem firmware locally or remotely
- reset individual card without bring down the server
- display current status of EIA signals
ISI Modem and Hybrid Ports Information:
---------------------------------------
For ISI3334-ISA card, all 8 ports are 33.6K V.34 modems
For ISI5634-PCI card, all 8 ports are 56K V.90 modems
For ISIHI/HP-2S card, the first 4 ports (port 1 to 4) are ISDN ST-Interface
and the last 4 ports (port 5 to 8) are 56K V.90 modems
For ISIHI/HP-2U card, the first 4 ports (port 1 to 4) are ISDN U-Interface
and the last 4 ports (port 5 to 8) are 56K V.90 modems
For ISIHP-4S card, the first 8 ports (port 1 to 8) are ISDN ST-Interface
and the last 8 ports (port 9 to 16) are 56K V.90 modems
For ISIHP-4U card, the first 8 ports (port 1 to 8) are ISDN U-Interface
and the last 8 ports (port 9 to 16) are 56K V.90 modems
ISA Card dip switch and jumper settings:
----------------------------------------
1. I/O address table
off = closed (switch down)
on = open (switch up)
Address Hex S1 S2 S3 S4 S5 S6 S7 S8
100 hex off off off off off on off off
110 hex off on off off off on off off
120 hex off off on off off on off off
130 hex off on on off off on off off
140 hex off off off on off on off off
150 hex off on off on off on off off
160 hex off off on on off on off off
170 hex off on on on off on off off
180 hex off off off off on on off off
190 hex off on off off on on off off
1A0 hex off off on off on on off off
1B0 hex off on on off on on off off
1C0 hex off off off on on on off off
1D0 hex off on off on on on off off
1E0 hex off off on on on on off off
1F0 hex off on on on on on off off
200 hex off off off off off off on off
210 hex off on off off off off on off
220 hex off off on off off off on off
230 hex off on on off off off on off
240 hex off off off on off off on off
250 hex off on off on off off on off
260 hex off off on on off off on off
270 hex off on on on off off on off
280 hex off off off off on off on off
290 hex off on off off on off on off
2A0 hex off off on off on off on off
2B0 hex off on on off on off on off
2C0 hex off off off on on off on off
2D0 hex off on off on on off on off
2E0 hex off off on on on off on off
2F0 hex off on on on on off on off
300 hex off off off off off on on off
310 hex off on off off off on on off
320 hex off off on off off on on off
330 hex off on on off off on on off
340 hex off off off on off on on off
350 hex off on off on off on on off
360 hex off off on on off on on off
370 hex off on on on off on on off
380 hex off off off off on on on off
390 hex off on off off on on on off
3A0 hex off off on off on on on off
3B0 hex off on on off on on on off
3C0 hex off off off on on on on off
3D0 hex off on off on on on on off
3E0 hex off off on on on on on off
3F0 hex off on on on on on on off
2. IRQ Jumpers
Setting interrupts is as simple as installing the jumper on the two pins
that indicate the interrupt vector.
For eg,
Interrupt 3 is chosen by the configuration below.
2 3 4 5 7 10 11 12 15
_
: |:| : : : : : : :
-
Support Options
---------------
For technical support, you may contact your authorized Multi-Tech
Systems distributor, dealer or the following Multi-Tech Systems
branch offices.
U.S.A. Web Site: www.multitecch.com
FTP Site: ftp.multitech.com
Tel: +1(612)785-3500 Fax: +1(612)785-9874
U.K. Tel: +44(118)959-7774 Fax: +44(118)959-7775
Europe Tel: +31(20)574-5910 Fax: +31(20)547-5911
Germany Tel: +49(89)547028-0 Fax: +49(89)547028-10
France Tel: +33(1)6461-0981 Fax: +33(1)6461-0971
China Tel: +86(10)6874-8015 Fax: +86(10)6874-8017
India Tel: +91(11)6174-634 Fax: +91(11)410-5968
Copyrights, Trademarks
----------------------
All documents and software provided herewith are Copyright (c) 1999
Multi-Tech Systems. All rights reserved.
MS, Windows, Windows 95, Windows NT are tradenames of
Microsoft Corporation.
Other trademarks or tradenames used herein are properties of the
respective owners.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.