1. inttok1.exe Driver
2. DOSDLC.TXT File Contents

DOSDLC.TXT Driver File Contents (inttok1.exe)

   DLC - DOS LAN Requester Workstation


   Installing and configuring the Intel TokenExpress(TM) 
   PRO adapter DLC driver for IBM Environments
   =====================================================

   Location of driver:  disk 2  \DOSDLC

      
   Quick Installation
   ------------------

      Use the Automatic Setup option in TokenSet (disk 1) to install
      the DLC drivers. 

      Sample CONFIG.SYS file
      ----------------------

	 FILES=20
	 BUFFERS=50
	 LASTDRIVE=E
	 DEVICE=C:\DLC\TPROARB1.SYS
	 DEVICE=C:\DLC\TPRODLC2.SYS
	 DEVICE=C:\DLC\DXMT0MOD.SYS   <--- Only for Netbios support


   General Installation
   --------------------

      The TokenExpress installation is dependent upon whether or 
      not your application requires the IBM Netbios protocol.

      1.  Create a directory on your system hard disk for the
	  TokenExpress DLC drivers.

      2.  Insert the Intel Driver disk 2 into drive A:.

      3.  Copy the Interrupt Arbitrator (A:\DOSDLC\TPROARB1.SYS) and
	  the DLC driver (A:\DOSDLC\TPRODLC2.SYS) to the newly created
	  directory on your hard drive.

      4.  If you are NOT using Netbios, skip to step 5.  If you are
	  using Netbios, copy the DXMT0MOD.SYS file to the newly created
	  directory on your hard drive.  The Netbios file, DXMT0MOD.SYS,
	  is found on the IBM LAN Support Program diskette (must be
	  purchased from IBM Corporation).

      5.  Edit your CONFIG.SYS file and add the following lines:

	     FILES=20
	     BUFFERS=50
	     LASTDRIVE=(drive_letter)
	     DEVICE=(full_path)\TPROARB1.SYS
	     DEVICE=(full_path)\TPRODLC2.SYS
	     DEVICE=(full_path)\DXMT0MOD.SYS   <--- Only for Netbios support
       
	  Where:

	     (drive_letter) is the designator of the
	     last local drive on your PC - e.g. E or F or ...)

	     (full_path) consists of the drive designator
	     followed by the name of the directory into which
	     the DLC driver and interrupt arbitrator have been
	     copied.  Refer to steps 1 and 2 above.

      6. Reboot your PC and install IBM DOS LAN Requester.


   Special Considerations
   ----------------------

      An optional country code can be specified when loading the 
      interrupt arbitrator TPROARB1.SYS.  Drivers loaded subsequently
      may then use this country code to display messages in the 
      selected language.

      The country code is specified in the CONFIG.SYS file as follows:

	 DEVICE = (path)\TPROARB1.SYS <optional country code>

      At this time, 001 for U.S. English is the only supported country 
      code.

      The TokenExpress DLC driver supports five (5) optional parameters.
      These parameters are specified in the CONFIG.SYS file as follows:

	 DEVICE=(path)\TPRODLC2.SYS -I<adapter number>9 -A -ON
				    -N<adapter number><node address>
				    -W<adapter number><work space size>

      Where:  

	 - or / precedes parameter option and <adapter number> 
	   specifies 0 or 1.
	 -I<adapter number>9 forces IRQ 9 to be used instead of IRQ 2
	 -A forces primary adapter to be configured as alternate 
	  adapter (1).  
	 -N<adapter number><node address> allows a locally administered
	   node address to be configured.
	 -W<adapter number><work space size> allows the LLC work space 
	   size to be specified.  (Min. 3072  - Max. 16384 bytes)
	   (Default = 4096 bytes.)
	 -ON specifies that an older version of IBM NetBIOS
	   (previous to v1.3) is being used.

     Examples:

	 REM *** Int 5C Arbitrator Driver ***
	 DEVICE=<path>\TPROARB1.SYS 001 
	   or
	 DEVICE=\LSP\DXMA0MOD.SYS 001 (IBM PC LAN Support v1.3)

	 REM *** DLC Driver ***
	 DEVICE=<path>\TPRODLC2.SYS -I09 -N1400001234567 -W05678

	 REM *** IBM NetBIOS Driver ***
	 DEVICE=\LSP\DXMT0MOD.SYS (IBM PC LAN Support v1.3)

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

• Expand the archive file (if the download file is in zip or rar format).

• If the expanded file has an .exe extension, double click it and follow the installation instructions.

• Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

• Find the device and model you want to update in the device list.

• Double-click on it to open the Properties dialog box.

• From the Properties dialog box, select the Driver tab.

• Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.