Workstation for DOS ODI Client v1.00 NetWare* DOS ODI Client Driver installation notes for Intel's EtherExpress(TM) PRO/100B LAN Adapter ============================================================= Location of Driver: \DOS\E100BODI.COM Quick Installation ------------------ Use the Automatic setup option in the SETUP utility on the Intel Configuration and Drivers disk to quickly and easily install the ODI driver. For workstations using VLM's, see the VLM client section below. Sample Configuration Files -------------------------- AUTOEXEC.BAT: CD\NWCLIENT LSL E100BODI IPXODI NETX or VLM (VLM's for NetWare 4.1 or 3.12) NET.CFG (for 802.3 clients - generally NetWare 2.x and 3.11 servers): LINK DRIVER E100BODI FRAME ETHERNET_802.3 NET.CFG (for 802.2 clients - generally NetWare 3.12 and 4.1 servers): LINK DRIVER E100BODI FRAME ETHERNET_802.2 NETWARE DOS REQUESTER FIRST NETWORK DRIVE = F General Installation for NetWare 2.2/3.11/3.12 clients ------------------------------------------------------ All the files necessary to connect to the NetWare servers are supplied on the Intel Configuration and Drivers disk. Newer versions of the shell files (LSL.COM, IPXODI.COM, NETX.EXE) may be available from Novell on CompuServe in the NetWire forum. To access this forum, type GO NOVFILES and download the files NET33X.EXE and VLMUP2.EXE. 1 From the \DOS directory on the Intel Configuration and Driver disk, copy the following files onto your hard drive: LSL.COM, E100BODI.COM, IPXODI.COM, NETX.EXE, and NET.CFG. 2 Add the commands to your AUTOEXEC.BAT file as shown above under the Sample Configuration Files section. Make sure you change to the subdirectory where the drivers are loaded before executing the files. In the example above, the drivers are located in the NWCLIENT subdirectory. 3 Edit the NET.CFG file per your requirements. If you don't know which frame type to load, type CONFIG from your file server console to see which frame type your file server is loading and load one of these frame types on the workstation. If you list two or more frame types in the NET.CFG, the IPX protocol will bind to the first frame type. The NET.CFG file should be in the same directory as the adapter driver. If you're running EMM386, make sure you are using v4.49 or later. It's the version that ships with DOS 6.22. 4 Reboot the computer and the drivers will load and connect you to the network. General Instructions for NetWare 4.1/3.12 client with VLMs ---------------------------------------------------------- The installation of the NetWare 4.1 client software is much easier than earlier versions. The installation procedure transfers files to a specific directory on the workstation and creates or modifies existing configuration files to fit your specific needs. The installation utility, INSTALL.EXE, is located on NetWare's "Workstation for DOS" disk. The install program is also located in \PUBLIC\CLIENT\DOSWIN on the server. NetWare 3.12 does not automatically create this directory on the server during installation. Installation Procedure for NetWare 4.1/3.12 client with VLMs ------------------------------------------------------------- 1 Run INSTALL.EXE from the NetWare Workstation for DOS Disk. 2 The NetWare Client Install program screen appears. You must complete each of the options as they are specific to your needs. Step #1: Specifies the directory on the hard drive that you want to install the client software. The default directory is C:\NWCLIENT. You can specify another directory if you desire. Step #2: Gives you the option to automatically update the CONFIG.SYS and the AUTOEXEC.BAT files or modify them at a later time manually. Step #3: Installs Windows software for your system if your workstation supports Windows and asks you to specify the directory where Windows is located. Step #4: Asks you to select a network driver and provide configuration options. It uses the specifications you select to create the file NET.CFG. Insert the Intel Configuration and Drivers disk when prompted for the driver disk. Intel EtherExpress PRO/100B is the name of the driver. Once you choose the driver, verify the configuration settings for the board if necessary. Step #5: The install program copies the appropriate files to your hard drive. This is the final step. 3 Be sure to add LASTDRIVE=Z to your CONFIG.SYS file and FIRST NETWORK DRIVE=F in the NET.CFG file under the Netware DOS Requestor section. Hints and tips ===================================================================== NET.CFG optional parameters --------------------------- FORCEDUPLEX: Specifies the duplex mode the driver uses. Syntax: FORCEDUPLEX n Where n=0 (auto-negotiate) 1 (half duplex) 2 (full duplex) NOTE: If adapter is set to half or full duplex, the SPEED parameter must be set to either 10 or 100. (see SPEED below) Duplex modes: Auto-negotiate _ the adapter negotiates with the hub how to send/receive packets, either full or half duplex. Full duplex _ the adapter sends and receives packets at the same time. This improves the performance of your adapter. Set duplex mode to full duplex ONLY if you have a full duplex hub that doesn't do auto-negotiation (a non-NWay* hub). Half duplex _ the adapter performs one operation at a time. It either sends or receives. Default: FORCEDUPLEX = Auto-Negotiate A regular adapter can perform only one operation at a time (half- duplexing). The PRO/100B adapter has the ability to send and receive packets at the same time (full-duplexing). In order to reap the benefits of full duplexing, you MUST have a full duplex hub. The PRO/100 adapter has the added ability to "talk" to the hub and determine at which mode to communicate (either full or half duplex). This is called auto-negotiation. You must have a auto- negotiating hub (an NWay hub) to get full duplex support with the FORCEDUPLEX parameter set to 0 (auto-negotiation). If you don't have an auto-negotiating hub, set FORCEDUPLEX to 2 (full duplex) and then set the SPEED parameter to either 100 Mbps or 10 Mbps. If you don't know what kind of hub you're attached to, contact your LAN Administrator SPEED: Specifies the speed the driver uses. If you don't use this parameter, the driver automatically detects the network speed. If no cable is attached, the driver defaults to 100 Mbps. If you don't have a auto-negotiating hub and are configuring the adapter for full-duplex support, you must specify the speed using this parameter. If you use this parameter, the driver operates at the specified speed instead of automatically detecting network speed. Syntax: SPEED n (n = 10 or 100) Default: none, the adapter automatically senses speed SLOT: Specifies the slot number. This is optional for single adapter installations, but required for multiple adapter installations. For PCI adapters, SLOT is derived from DEVICE LOCATION and doesn't map to the physical location of the adapter. Currently, the PCI specification doesn't tell you how to determine which adapter corresponds to a device number. However, you can run the SETUP.EXE utility from the Intel Configuration and Drivers diskette and view the adapter's slot number (and device location in hex). Another way to do this is to load the driver from the command line. You'll be prompted with valid device numbers for the adapter. Select one of them. Syntax: SLOT n (n = 1,2,3,4,...15). THRESHOLD: Represents the threshold for transmits from extender SRAM FIFO. By default threshold is dynamically set based on driver activity. This parameter only sets a starting value. It will still dynamically change. Syntax: THRESHOLD n (n = number of 8 bytes). For example, 16 represents 16x8 (or 128 bytes).. Default: 16 The maximum number that you can specify is 200 (200x8=1600 bytes). NODE ADDRESS: Specifies a local node address unique to each adapter. The first four digits of the address indicate who assigned the address when the driver loads. The node address is also printed on a sticker on the back edge of adapter. See the Installation Guide for a picture of the adapter showing the location of the sticker. Syntax: NODE ADDRESS 00aa12345678 02aa => Locally administered address, 02 is set by MSM 00aa => Typical Intel address (default) FRAME: Indicates one of four valid frame types the system is transmitting and receiving. Syntax: FRAME n n = Ethernet_802.2 Ethernet_802.3 Ethernet_II Ethernet_SNAP Default: Ethernet_802.2 PROTOCOL: Indicates the standard protocol in use. Syntax: Protocol IPX E0 Ethernet_802.2 Values: E0=Ethernet_802.2 0=Ethernet_802.3 8137=Ethernet_II 8137=Ethernet_SNAP NetWare DOS Requester ===================== PB BUFFERS: A hexadecimal number representing number of packets in a single transmit burst sequence used by VLM. The default is 16 (10h). FIRST NETWORK DRIVE: (Used only with the VLM.EXE). Indicates the first network drive available in the client system. Note: If you use FIRST NETWORK DRIVE, the last line in the CONFIG.SYS file must read: LASTDRIVE=Z Detailed example ---------------- LINK DRIVER E100ODI SLOT 1 SPEED 100 THRESHOLD 16 BUS 2 NODE ADDRESS 00aa00xxxxxx <--Last six digits are unique for each adapter) FRAME ETHERNET_802.2 PROTOCOL IPX E0 ETHERNET_802.2 In addition, the NET.CFG file can contain the following optional information: NETWARE DOS REQUESTER PB BUFFERS=10 FIRST NETWORK DRIVE=F * Third-party trademarks are the property of their respective owners.Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.