Thomas-Conrad Corporation IBM LAN Server Driver for TC4035, TC4045, TC4046 and TC4145 Token Ring Adapters This README explains how to use the IBM LAN Server driver for the TC4035, TC4045, TC4046 and TC4145 token ring adapters. After uncompression, there will be two subdirectories, shown below: * DOS-based workstations: The driver is named TCCTOK.DOS and is located in directory DOS. * OS/2-based workstations: The driver is named TCCTOK.OS2 and is located in directory OS2. ****************** * RUN RING TOOLS * ****************** You should run the Ring Tools diagnostic test suite on the adapter before you attempt to install drivers. Ring Tools will indicate serious hardware problems, such as hardware incompatibility or adapter faults. See Chapter 4 of the manual shipped with the adapter for detailed instructions. ************************ * COPYING EAGLEMAC.BIN * ************************ DOS driver only: Before installing the driver on a DOS-based workstation, copy the file named EAGLEMAC.BIN from the root directory of the driver diskette to the root directory of your boot drive or boot diskette. Or, you can copy EAGLEMAC.BIN to either the \IBMCOM\MACS directory (which is where the driver is located) or to the \IBMCOM directory. This action is not necessary if you are using the OS/2 driver. ************************************ * DRIVER COMPATIBILITY AND SUPPORT * ************************************ Drivers and configuration files for IBM LAN Server are located in the DOS and OS2 directories on the driver diskette after uncompression (see the beginning of this README). These drivers also support source-routing, and will automatically send and respond to LLCPOLL packet, which are used by some management systems). No driver parameter or other action is necessary to enable either of these features. ************************* * ADAPTER CONFIGURATION * ************************* DOS-based LAN Support drivers only: The LAN Support drivers are located in the directory LANSUP on the driver diskette. If you are using LAN Support drivers in a DOS-based workstation, you must make sure the adapter is set as shown below (see Chapter 3 of the manual shipped with your adapter for information about adapter settings): IRQ: 2/9, 3, 6 or 7 DMA-Base I/O: DMA 5 and Base I/O 1A20h (Primary, also adapter defaults) DMA 6 and Base I/O 2A20h (Alternate) If you are using NDIS drivers with IBM LAN Support, you can use any available adapter configuration. You are not restricted to the settings shown above. ******************************************* * RUNNING THE LAN SUPPORT PROGRAM UTILITY * ******************************************* Set up the driver in LAN Server by running the LAN Support Program configuration utility (DXMAID.EXE), which ships with the LAN Server program. Follow the prompts on your screen to complete the installation process. The driver and configuration file for DOS-based systems are located in the DOS directory after uncompression; the driver and configuration file for OS/2-based systems are located in the OS2 directory after uncompression. ****************** * REMOTE BOOTING * ****************** To set up a DOS-based workstation to remote boot in a IBM LAN Server environment, take the following actions: * Install the TC9245 Remote Reset (RPL) ROM on the adapter as shown in Chapter 3 of the manual shipped with your adapter. The diskette that ships with the TC9245 has installation instructions that must be followed by the network administrator to enable remote booting. * Use the Thomas-Conrad LAN Support drivers located in the directory named LANSUP on this diskette. The directory contains documentation for the drivers. ***************** * FOR MORE HELP * ***************** For more help, contact Thomas-Conrad Technical Support in one of the ways shown below. Free telephone support is available 24 hours-a-day, 7 days-a-week. Technical Support (800) 334-4112 Toll free, U.S. (800) 654-3822 Toll free, Canada (512) 836-1935 Corporate switchboard (512) 836-8012 BBS (512) 837-6080 FAX CompuServe GO TCCFORUM World Wide Web HTTP://WWW.TCI.COM email SUPPORT@KLAVEN.TCI.COM FTP server: FTP.TCI.COM In Europe: Thomas-Conrad Europe Limited Coworth Park House Ascot, SL5 7SF United Kingdom +44 1344-875175 European headquarters +44 1344-875176 FAX +44 1344-291301 BBS 0800 374681 Toll free Thomas-Conrad Sarl 70 rue Anatole France, 92300 Levallois-Perret Paris France +33 1 47591900 French office +33 1 47591901 FAX +33 1 47591902 BBS Thomas-Conrad GmbH Friedrich-Wilhelm Strasse 86-96 47051 Duisburg Germany +49-203-295170 German office +49-203-2951717 FAX +49-203-2951727 BBS 0130-11-5891 Toll free All bulletin boards (BBS) accept calls at 1200/2400/4800/9600 bps. This line uses a v.32 modem that supports MNP Level 5. Set up your communication software for 8 data bits, 1 stop bit, and no parity.Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.