//**************************************************************************** // Samsung Electronics // Copyright (c) 2004 Samsung Electronics Co., All Rights Reserved //**************************************************************************** // TITLE: Hi_miniD.txt // DATE CREATED: 2004/08/27 // DESCRIPTION: mBMC initialization file for SS130. // //**************************************************************************** // REVISION HISTORY: // Rev 0.D Changed CMOS clear PEF table and removed FRB3 feature. // Rev 0.C Changed lookup table for binding CPU temp. // Rev 0.B Changed LED conversion map for blinking // Rev 0.A Changed LED Control table and PEF table // Rev 0.9 Changed Heceta access method // Rev 0.8 Changed Product name // Rev 0.7 Changed mBMC configuration for register 09h, 0Ah, 38h // Updated LM93 INIT table with thermal propile // Modified sensor access table for fans // Enabled FRB3 feature // Rev 0.6 Updated PEF table and SIT for Fab2 // Changed Sesnor Number and removed unused sensors // Updated PEF table // Rev 0.5 Updated PEF table and SIT for Fab1 // Changed Sesnor Number and removed unused sensors // Updated PEF table // Rev 0.4 Updated fab2 changes // Rev 0.3 Fixed Sensor access table error and PEF table error // Rev 0.2 Updated EPS 0.5 changes // Rev 0.1 Initial revision. // //**************************************************************************** // ================================ // mBMC configuration // ================================ // Flash control, IPMI Master Write-Read access enable. c 84 18 52 11 00 00 3A 00 00 4E 53 43 00 00 00 00 00 00 00 00 00 00 00 00 00 //SET NIC LOM slave address To mBMC. c 84 18 52 11 00 00 01 00 86 //Setup Identification LED color GREEN 1 Hz, Fault LED color RED 1 Hz c 84 18 52 11 00 00 04 00 51 //SMBus alert isolation is disabled c 84 18 52 11 00 00 05 00 80 //Configur DEIO01 --output level 1, CMOS clear c 84 18 52 11 00 00 06 00 A2 c 84 18 52 11 00 00 07 00 00 //FRB Halt c 84 18 52 11 00 00 08 00 0C //Start-up delay is 1sec c 84 18 52 11 00 00 09 00 0A //Sensor Polling Delay is 2sec c 84 18 52 11 00 00 0A 00 14 //LED color conversion control, enable LED2 blinking and solid color conversion c 84 18 52 11 00 00 16 00 30 //solid color conversion, map Off to LEDC2 active and reversely c 84 18 52 11 00 00 19 00 B5 //blinking color conversion, map Off to LEDC2 active and reversely c 84 18 52 11 00 00 1A 00 B5 //DEIO Polarity SecureMode signal is active high (DEIO6) c 84 18 52 11 00 00 1E 00 20 //FRB WD Timer enbale (00->8C) c 84 18 52 11 00 00 20 00 00 //FRB WD Timer value c 84 18 52 11 00 00 21 00 A0 //TRIS/ENBL config c 84 18 52 11 00 00 22 00 BA //IANA ID //c 84 18 52 11 00 00 23 00 00 //IANA ID //c 84 18 52 11 00 00 24 00 00 //NMI signal is low level, Chassis always power-off after AC resume c 84 18 52 11 00 00 26 00 00 //Chassis Intrusion Sensor Number is 0Ah c 84 18 52 11 00 00 27 00 00 //FRU Inventory Size is F8h c 84 18 52 11 00 00 38 00 F8 // Enable PEF and Change LED default,oppisite color priority, blinking is 5, solid is 4. c 84 18 52 11 00 00 3B 00 08 //Enable PEF configuration and Change LED default color priority, blinking is 3, solid is 2 c 84 18 52 11 00 00 3C 00 C2 //allow MD5 and none access to O and A privilege level c 84 30 01 00 02 00 15 15 15 00 // ================================ // Sensor Access Table // ================================ //Chassis Intrusion: 8-bit. SIO address is 6Ch. LDN 04, Register 0Ch. c 84 18 52 11 00 00 00 02 0A 12 7C 00 00 04 0C 6C //CPU1 12V: 8-bit. LM93 address is 2E.Register 56h. c 84 18 52 11 00 00 08 02 10 02 04 00 00 56 00 2E //CPU2 12V: 8-bit. LM93 address is 2E.Register 57h. c 84 18 52 11 00 00 10 02 11 02 04 00 00 57 00 2E //BB +1.5V: 8-bit. LM93 address is 2E.Register 5Ah. c 84 18 52 11 00 00 18 02 12 02 04 00 00 5A 00 2E //BB +1.8V: 8-bit. LM93 address is 2E.Register 61h. c 84 18 52 11 00 00 20 02 13 02 04 00 00 61 00 2E //BB +3.3V: 8-bit. LM93 address is 2E.Register 5Eh. c 84 18 52 11 00 00 28 02 14 02 04 00 00 5E 00 2E //BB +5V: 8-bit. LM93 address is 2E.Register 5Fh. c 84 18 52 11 00 00 30 02 15 02 04 00 00 5F 00 2E //BB +12V: 8-bit. LM93 address is 2E.Register 58h. c 84 18 52 11 00 00 38 02 16 02 04 00 00 58 00 2E //BB -12V: 8-bit. LM93 address is 2E.Register 64h. c 84 18 52 11 00 00 40 02 17 02 04 00 00 64 00 2E //FSB Vtt: 8-bit. LM93 address is 2E. Register 59h. c 84 18 52 11 00 00 48 02 18 02 04 00 00 59 00 2E //SCSI Core: 8-bit. LM93 address is 2E. Register 60h. c 84 18 52 11 00 00 50 02 19 02 04 00 00 60 00 2E //Proc1 VCCP: 8-bit. LM93 address is 2E.Register 5Ch. c 84 18 52 11 00 00 58 02 1A 02 04 00 00 5C 00 2E //Proc2 VCCP: 8-bit. LM93 address is 2E.Register 5Dh. c 84 18 52 11 00 00 60 02 1B 02 04 00 00 5D 00 2E //Tach Fan 1A: 16-bit. SIO address is 6Ch. LDN 09, FCB offset 0f, Bank 00h, Register 13h. c 84 18 52 11 00 00 68 02 20 52 BC 0F 00 09 12 6C //Tach Fan 1B: 16-bit. SIO address is 6Ch.LDN 09, FCB offset 0f, Bank 02h, Register 12h. c 84 18 52 11 00 00 70 02 21 52 BC 0F 02 09 12 6C //Tach Fan 2A: 16-bit.SIO address is 6Ch. LDN 09, FCB offset 0f, Bank 03h, Register 12h. c 84 18 52 11 00 00 78 02 22 52 BC 0F 03 09 12 6C //Tach Fan 2B: 16-bit. SIO address is 6Ch. LDN 09, FCB offset 0f, Bank 04h, Register 12h. c 84 18 52 11 00 00 80 02 23 52 BC 0F 04 09 12 6C //Tach Fan 3A: 16-bit. SIO address is 6Ch.LDN 09, FCB offset 0f, Bank 06h,Register 12h. c 84 18 52 11 00 00 88 02 24 52 BC 0F 06 09 12 6C //Tach Fan 3B: 16-bit. SIO address is 6Ch.LDN 09, FCB offset 0f, Bank 07h, Register 12h. c 84 18 52 11 00 00 90 02 25 52 BC 0F 07 09 12 6C //Tach Fan 4A: 16-bit.LM93 address is 2E.Register 6Eh. c 84 18 52 11 00 00 98 02 26 52 A4 00 00 6E 00 2E //Tach Fan 4B: 16-bit. LM93 address is 2E.Register 70h. c 84 18 52 11 00 00 A0 02 27 52 A4 00 00 70 00 2E //Tach Fan 5A: 16-bit.LM93 address is 2E.Register 72h. c 84 18 52 11 00 00 A8 02 28 52 A4 00 00 72 00 2E //Tach Fan 5B: 16-bit. LM93 address is 2E.Register 74h. c 84 18 52 11 00 00 B0 02 29 52 A4 00 00 74 00 2E //Heceta Temp: 8-bit. LM93 address is 2E.Register 52h. c 84 18 52 11 00 00 B8 02 30 02 44 00 00 52 00 2E //FP Temp: 8-bit. FP address is 4Dh, Read Temp from 00h. c 84 18 52 11 00 00 C0 02 31 02 44 00 00 00 00 4D //Proc 1 temp: 8-bit. LM93 address is 2E.Register 50h. c 84 18 52 11 00 00 C8 02 40 02 04 00 00 50 00 2E //Proc 2 temp: 8-bit. LM93 address is 2E.Register 51h. c 84 18 52 11 00 00 D0 02 41 02 04 00 00 51 00 2E //Proc 1 Throttle: 8-bit. LM93 address is 2E.Register 67h c 84 18 52 11 00 00 D8 02 42 02 04 00 00 67 00 2E //Proc 2 Throttle: 8-bit. LM93 address is 2Eh.Register 69h. c 84 18 52 11 00 00 E0 02 43 02 04 00 00 69 00 2E //Proc 1 IERR: 1-bit. LM93 address is 2E.Register 6Bh. c 84 18 52 11 00 00 E8 02 50 62 24 00 00 6B 00 2E //Proc 2 IERR: 1-bit. LM93 address is 2E.Register 6Bh. c 84 18 52 11 00 00 F0 02 51 72 24 00 00 6B 00 2E //Proc 1 Thermal trip: 1-bit. LM93 address is 2E.Register 6Bh. c 84 18 52 11 00 00 F8 02 52 32 24 00 00 6B 00 2E //Proc 2 Thermal trip: 1-bit. LM93 address is 2E.Register 6Bh. c 84 18 52 11 00 00 00 03 53 42 24 00 00 6B 00 2E //CPU config Error: 1-bit. mBMC DEIO 2 . c 84 18 52 11 00 00 08 03 58 12 40 00 00 00 00 A1 //Diagnostic interrupt Button: 1-bit. mBMC DEIO 8. c 84 18 52 11 00 00 10 03 60 02 00 00 00 00 00 A7 //chassis Identify Button: 1-bit. mBMC DEIO 7. c 84 18 52 11 00 00 18 03 61 12 40 00 00 00 00 A6 //Last entry c 84 18 52 11 00 00 20 03 00 00 00 00 00 00 00 00 // ================================ // Disable Sensor Interface // ================================ c 84 18 52 11 00 00 03 00 04 // ============================ // Sensor Init. Table // ============================ // FP Amb. Temp Sensor init. (LM75) c 84 18 52 11 00 00 00 01 02 4D 01 00 00 // Heceta Configuration (LM93) // Zone4 High Limit Register. c 84 18 52 11 00 00 05 01 02 2E 7F 7F 00 // Fan Boost Temp register, Zone1/2 (88/88) c 84 18 52 11 00 00 0A 01 02 2E 80 58 00 c 84 18 52 11 00 00 0F 01 02 2E 81 58 00 // Fan Boost Temp register, Zone 3/4 (65/40) c 84 18 52 11 00 00 14 01 02 2E 82 41 00 c 84 18 52 11 00 00 19 01 02 2E 83 28 00 // Ramp Up register VRD_HOT Ramp 200ms c 84 18 52 11 00 00 1E 01 02 2E BF 04 00 // Zone 3/4 Fan Boost Hysteresis, 2h/2h c 84 18 52 11 00 00 23 01 02 2E C1 22 00 // Zone 1/2 Spike smoothing, 3sec c 84 18 52 11 00 00 28 01 02 2E C2 BB 00 // Zone 1/2 MinPWM and Hysteresis, 0% c 84 18 52 11 00 00 2D 01 02 2E C3 01 00 // Zone 3/4 MinPWM and Hysteresis, 0% c 84 18 52 11 00 00 32 01 02 2E C4 01 00 // PWM1 is bound to zone1 and 4 (FP temp and CPU1) c 84 18 52 11 00 00 37 01 02 2E C8 09 00 // Spin-up, 1000ms & 85% duty cycle c 84 18 52 11 00 00 3C 01 02 2E CA AA 00 // PWM2 bound to zone 4 (FP temp) c 84 18 52 11 00 00 41 01 02 2E CC 08 00 // PWM2 Spin-up, 1000ms & 85% duty cycle c 84 18 52 11 00 00 46 01 02 2E CE AA 00 // Zone 1 base temperature (83) c 84 18 52 11 00 00 4B 01 02 2E D0 53 00 // Zone 4 base temperature (35) c 84 18 52 11 00 00 50 01 02 2E D3 23 00 // Look up table (12 Entries) c 84 18 52 11 00 00 55 01 02 2E D4 52 00 c 84 18 52 11 00 00 5A 01 02 2E D5 02 00 c 84 18 52 11 00 00 5F 01 02 2E D6 02 00 c 84 18 52 11 00 00 64 01 02 2E D7 02 00 c 84 18 52 11 00 00 69 01 02 2E D8 00 00 c 84 18 52 11 00 00 6E 01 02 2E D9 00 00 c 84 18 52 11 00 00 73 01 02 2E DA 00 00 c 84 18 52 11 00 00 78 01 02 2E DB 00 00 c 84 18 52 11 00 00 7D 01 02 2E DC 00 00 c 84 18 52 11 00 00 82 01 02 2E DD 00 00 c 84 18 52 11 00 00 87 01 02 2E DE 55 00 c 84 18 52 11 00 00 8C 01 02 2E DF 11 00 // 1-index:E3, data:81---bit0=1, enable LM93 c 84 18 52 11 00 00 91 01 02 2E E3 01 00 // Last entry c 84 18 52 11 00 00 96 01 80 FF 00 00 00 // ============================ // Sensor Bridge Table (01D0) // ============================ // 1-Source:2d, Destination:5c, index=53h c 84 18 52 11 00 00 D0 01 01 31 2E 53 00 00 // Last entry c 84 18 52 11 00 00 D6 01 80 00 00 00 00 00 // =============================== // Disable PEF filtering // =============================== c 84 10 12 01 00 // =============================== // Update PEF entries // =============================== // 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 // Analog Sensor Assertion of Non-critical, Blinking Amber c 84 10 12 06 01 c0 10 01 10 20 FF FF FF 01 81 00 00 FF 00 00 FF 00 00 FF 00 c 84 10 12 60 01 00 01 00 00 00 00 00 00 00 00 00 00 // Analog Sensor Assertion of critical, solid amber c 84 10 12 06 02 c0 10 01 20 20 FF FF FF 01 04 02 00 FF 00 00 FF 00 00 FF 00 c 84 10 12 60 02 00 09 00 00 00 00 00 00 00 00 00 00 // Analog Sensor deAssertion of all, Solid green c 84 10 12 06 03 c0 10 01 04 20 FF FF FF 81 85 02 00 FF 00 00 FF 00 00 FF 00 c 84 10 12 60 03 00 04 00 00 00 00 00 00 00 00 00 00 // Proc 1/2 IERR Assertion, Solid amber c 84 10 12 06 04 c0 10 01 20 20 FF 07 FF 6F 01 00 00 FF 00 00 FF 00 00 FF 00 c 84 10 12 60 04 00 09 00 00 00 00 00 00 00 00 00 00 // Proc 1/2 Thermal Trip Assertion, Solid amber c 84 10 12 06 05 C0 12 01 20 20 FF 07 FF 6F 02 00 00 FF 00 00 FF 00 00 FF 00 c 84 10 12 60 05 00 09 00 00 00 00 00 00 00 00 00 00 // Digital Sensor Deassert of all, Solid green c 84 10 12 06 06 C0 10 01 04 20 FF FF FF EF FF FF 00 FF 00 00 FF 00 00 FF 00 c 84 10 12 60 06 00 04 00 00 00 00 00 00 00 00 00 00 // Watchdog Expired. Blinking Green c 84 10 12 06 07 C0 10 01 08 20 FF 23 FF 6F 0F 00 00 FF 00 00 FF 00 00 FF 00 c 84 10 12 60 07 00 02 00 00 00 00 00 00 00 00 00 00 // Proc 1/2 Thermal Control assertion, Blinking green c 84 10 12 06 08 C0 10 01 08 20 FF 01 FF 01 80 02 00 FF 00 00 FF 00 00 FF 00 c 84 10 12 60 08 00 02 00 00 00 00 00 00 00 00 00 00 // Proc 1/2 Thermal Control deassertion, Solid green c 84 10 12 06 09 C0 10 01 08 20 FF 01 FF 81 80 02 00 FF 00 00 FF 00 00 FF 00 c 84 10 12 60 09 00 04 00 00 00 00 00 00 00 00 00 00 // FP NMI Button, Solid amber c 84 10 12 06 0A C0 30 01 20 20 FF 13 FF 6F 01 00 00 FF 00 00 FF 00 00 FF 00 c 84 10 12 60 0A 00 09 00 00 00 00 00 00 00 00 00 00 // FP ID Button, Solid Blue Toggle c 84 10 12 06 0B C0 10 01 10 FF FF 14 61 03 02 00 00 FF 00 00 FF 00 00 FF 00 c 84 10 12 60 0B 00 80 00 00 00 00 00 00 00 00 00 00 // OS Load POST Code, Solid green c 84 10 12 06 0C C0 10 01 02 03 FF 12 FF 6F 02 00 00 FF 00 00 FF 00 00 FF 00 c 84 10 12 60 0C 00 00 00 00 00 00 00 00 00 00 00 00 // CMOS Clear, DEIO1 Assert c 84 10 12 06 0D C0 18 01 02 20 00 14 04 03 02 00 FF 00 FF FF 00 FF FF 00 FF c 84 10 12 60 0D 04 00 00 00 80 A0 00 00 00 00 00 00 // Chassis Intrusion, LAN Alert c 84 10 12 06 1A C0 01 01 02 20 FF 05 FF 6F 01 00 00 FF 00 00 FF 00 00 FF 00 // POST Code Error, LAN Alert c 84 10 12 06 1B C0 01 01 02 FF FF 0F FF 6F FF FF 00 FF 00 00 FF 00 00 FF 00 // Voltage Failure, LAN Alert c 84 10 12 06 1C C0 01 01 10 20 FF 02 FF 01 85 02 00 FF 00 00 FF 00 00 FF 00 // Fan Failure, LAN Alert c 84 10 12 06 1D C0 01 01 10 20 FF 04 FF 01 81 00 00 FF 00 00 FF 00 00 FF 00 // Temperature Failure, LAN Alert c 84 10 12 06 1E C0 01 01 10 20 FF 01 FF 01 81 00 00 FF 00 00 FF 00 00 FF 00 // ============================ // Enable PEF filtering // ============================ // Parameter #1 to enable PEF, event message, PEF startup delay, // and Alert Startup delay (Default 0x0F) c 84 10 12 01 01 // ============================ // Enable Sensor Interface // ============================ // Enable Sensor interface c 84 18 52 11 00 00 03 00 0C // ********************************************* // * Finished mBMC Flash Initialization * // *********************************************Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.