****************************************************************************
MPTBIOS.TXT
*****************************************************************************
This file presents general information about the LSI Logic Fusion-MPT (TM)
SCSI BIOS and Configuration Utility.
This text file is divided into these sections:
SCSI BIOS
Features
Boot Initialization with SCSI BIOS Boot Specification
CD-ROM Boot Initialization
Starting the SCSI BIOS Configuration Utility
Using the Configuration Utility
Main Menu
Boot Adapter List
Global Properties
Adapter Properties
Device Properties
RAID Properties
Quitting the SCSI Configuration Utility
* * * * * * * * * * * * SCSI BIOS * * * * * * * * * * *
A SCSI BIOS is the bootable ROM code that manages SCSI hardware resources. It
is specific to a family of LSI Logic Fusion-MPT SCSI controllers or processors.
A Fusion-MPT SCSI BIOS integrates with a standard system BIOS, extending the
standard disk service routine provided through INT13h.
During the boot time initialization, the SCSI BIOS determines if there are
other hard disks, such as an IDE drive, already installed by the system BIOS.
If there are, the SCSI BIOS maps any SCSI drives it finds behind the drive(s)
already installed. Otherwise, the SCSI BIOS installs drives starting with the
system boot drive. In this case, the system boots from a drive controlled by
the SCSI BIOS. The LSI Logic BIOS supports the BIOS Boot Specification (BBS).
The next section, "Boot Initialization with BIOS Boot Specification (BBS),"
discusses selecting boot and drive order.
* * * * * * * * * * * Features * * * * * * * * * * * *
The Fusion-MPT SCSI BIOS features include:
o Configuration for up to 256 adapters-any 4 can be chosen for
INT13 (bootrom) support
o Support for Message Passing Technology
o Support for the LSI53C1020 device
o Support for the LSI53C1030 device
o Support for SPI-3 Parallel Protocol Request (PPR)
o Support for Domain Validation
o Support for transfer rates up to Ultra320 SCSI (320 Mbytes/s)
* * * * Boot Initialization with BIOS Boot Specification (BBS) * * *
The Fusion-MPT SCSI BIOS provides support for the BIOS Boot Specification
(BBS), which allows you to choose which device to boot from by selecting the
priority.
To use this feature, the system BIOS must also be compatible with the BBS. If
your system supports the BBS, then you will use the system BIOS setup menu to
select the boot and drive order. In the system BIOS setup, the Boot Connection
Devices menu appears with a list of available boot options. Use that menu to
select the device and rearrange the order. Then exit to continue the boot
process.
* * * * * * * * * CD-ROM Boot Initialization * * * * * * * * *
The Fusion-MPT SCSI BIOS supports boot initialization from a CD-ROM drive.
The five types of emulation are:
o No emulation disk
o Floppy 1.2 Mbyte emulation disk
o Floppy 1.44 Mbyte emulation disk
o Floppy 2.88 Mbyte emulation disk
o Hard disk emulation
The type of emulation assigns the drive letter for the CD-ROM. For example,
if a 1.44 Mbyte floppy emulation CD was loaded, then the CD-ROM drive would
become the designated A: drive, and the existing floppy would become drive B:.
* * * * * * Starting the SCSI BIOS Configuration Utility * * * * * *
If you have SCSI BIOS version 5.XX, and it includes the Fusion-MPT SCSI BIOS
Configuration Utility, you can change the default configuration of your SCSI
host adapters. You may decide to alter these default values if there is a
conflict between device settings or if you need to optimize system performance.
You can see the version number of the SCSI BIOS in a banner displayed on
your computer monitor during boot. If the utility is available, this message
also appears on your monitor:
Press Ctrl-C to start LSI Logic Configuration Utility...
This message remains on your screen for about five seconds, giving you time
to start the utility. If you decide to press "Ctrl-C", the message changes
to:
Please wait, invoking LSI Logic Configuration Utility...
After a brief pause, your computer monitor displays the Main Menu of the
Fusion-MPT PCI SCSI BIOS Configuration Utility.
These messages may appear during the boot process:
1. "Adapter removed from boot order"
appears when an adapter is removed from the system or relocated behind a
PCI bridge.
2. "Persistent settings INVALID, defaults saved" appears
if none of the information in the NVRAM is valid.
IMPORTANT: The SCSI BIOS Configuration Utility is a powerful tool. If, while
using it, you somehow disable all of your controllers, pressing
Ctrl-A (or Ctrl-E on version 5.00 or later) after memory
initialization during reboot allows you to re-enable and
reconfigure.
Note: Not all devices detected by the Configuration Utility can be
controlled by the BIOS. Devices such as tape drives and scanners
require that a device driver specific to that peripheral be
loaded. The SCSI BIOS Configuration Utility does allow parameters
to be modified for these devices.
* * * * * * * Using the Configuration Utility * * * * * * * *
* * * Screen Format * * *
All SCSI BIOS Configuration Utility screens are partitioned into the fixed
areas. Here is an example:
X 0 79
Y ----------------------------------------
0 | Header Area |
----------------------------------------
1 | Menu Area |
----------------------------------------
2 | |
| |
... Main Area ...
| |
21 | |
----------------------------------------
22 | |
| Footer Area |
24 | |
----------------------------------------
Header Area
This area provides static information text, which is typically
the product title and version.
Menu Area
This area provides the current Main Area's menu, if any.
This area has a cursor for menu item selection.
Main Area
This is the main area for presenting data. This area has a cursor for
item selection, horizontal scrolling, and vertical scrolling. The
horizontal and vertical scroll bars appear here.
Footer Area
This area provides general help information text.
* * * User Input * * *
Throughout the GUI, selections that are not permissible are grayed out.
F2 = Menu
Sets cursor context to the menu selection area.
Select a menu item and press Enter.
Arrow Keys = Select Item
Home/End = Select Item
Up, down, left, right movement to position the cursor.
+/- = Change [Item]
Items with values in [] brackets are modifiable.
Numeric keypad '+' and numeric keypad '-', update a modifiable field to
its next relative value.
Esc = Abort/Exit
Escape aborts the current context operation and/or exits the current
screen. User confirmation is solicited as required.
Enter = Execute <Item>
Items with values in <> brackets are executable.
Press Enter to execute the field's associated function.
* * * * * * * * * * * Main Menu * * * * * * * * * * * *
When you invoke the Fusion-MPT SCSI BIOS Configuration Utility, the Main Menu
appears. This screen displays a scrolling list of up to 256 LSI Logic PCI to
SCSI host adapters in the system and information about each of them.
Use the arrow keys to select an adapter, then press Enter to view and modify
the selected adapter's properties (and to gain access to the attached devices).
Only adapters with LSI Logic Control enabled can be accessed. After selecting an
adapter and pressing Enter, the adapter's SCSI bus is scanned and the
Adapter Properties screen appears. An example is shown below.
On the Main Menu, two selections are: Boot Adapter List and Global Properties.
Boot Adapter List allows selection and ordering of boot adapters. Refer to
the section on Boot Adapter List below.
Global Properties allows changes to global scope settings. Refer to the
section on Global Properties below.
To execute an item, select it and press Enter. Here is an example of
the Main Menu:
|-----------------------------------------------------------------------------|
| LSI Logic MPT SCSI Setup Utility Version MPTBIOS -x.xx |
| <Boot Adapter List> <Global Properties> |
| |
| LSI Logic Host Bus Adapters |
| Adapter PCI Dev/ Port IRQ NVM Boot LSI Logic RAID |
| Bus Func Number Order Control Status |
| <LSI1030 0 20> E400 10 --- 0 Enabled -- |
| <LSI1030 0 21> E000 12 Yes 1 Enabled -- |
| <LSI1030 0 60> F800 9 Yes 2 Enabled -- |
| <LSI1030 0 A0> E800 11 Yes 3 Enabled -- |
|-----------------------------------------------------------------------------|
* * * Field Descriptions * * *
Adapter Indicates the specific family of LSI Logic Host Adapters.
PCI Bus Indicates the PCI Bus number (range 0x00 - 0xFF, 0 - 255 decimal)
assigned by the system BIOS to an adapter.
Dev/Func Indicates the PCI Device/Function assigned by the system BIOS to
an adapter.
An 8-bit value mapped as follows:
Bit # 7 6 5 4 3 2 1 0
|___________| |_____|
| |> Bits 2-0: Function (range 0 - 7)
|> Bits 7-3: Device (range 0x00 - 0x1F, 0 - 31 decimal).
Port Number Indicates the I/O Port Number that communicates with an adapter. The
system BIOS assigns this number.
IRQ Indicates the Interrupt Request Line used by an adapter.
The system BIOS also assigns this value.
NVM Indicates whether an adapter has non-volatile memory (NVM)
associated with it. An adapter's configuration is stored in its
associated NVM.
Boot Order Indicates the relative boot order (0 to 3) of an adapter.
The Fusion-MPT SCSI BIOS traverses up to four adapters in the
specified order in search of bootable media. Access the
"Boot Adapter List" Menu to modify this item.
LSI Logic Indicates whether an adapter is eligible for LSI Logic software
Control control or is reserved for control by non-LSI Logic software.
RAID Status A status indicates the existence of a RAID array on an adapter
and what state its in. "--" indicates no RAID array found on
adapter.
Global Indicates global properties that are not associated with a
Properties specific adapter or device.
* * * * * * * * * * Boot Adapter List * * * * * * * * * *
The adapter boot order specifies the order in which adapters will boot when
more than one os adapter is in a system.
Up to four of the total adapters in a system may be selected as bootable.
To add an adapter to the boot list, press Insert while on the Boot Adapter
List. This puts the cursor on the adapter select list. Use the arrow keys to
select the desired adapter and press Enter to add it to the end of Boot
Adapter List.
To remove an adapter from the boot list, press Delete while on the desired
adapter in the Boot Adapter List. Here is an example of the Boot Adapter
List Menu:
|-------------------------------------------------------------|
| LSI Logic MPT SCSI Setup Utility Version MPTBIOS -x.xx |
| |
| Boot Adapter List |
| Insert=Add an adapter Delete=Remove an adapter |
| |
| Adapter PCI Dev/ Boot Current Next |
| Bus Func Order Status Boot |
| <LSI1030 0 60> [0] On [On] |
| <LSI1030 0 61> [1] On [On] |
| <LSI1030 0 98> [2] On [On] |
| <LSI1030 0 A0> [3] On [On] |
| |
| Press Insert to select an adapter from this list: |
| <LSI1030 0 60> |
| <LSI1030 0 61> |
| <LSI1030 0 98> |
| <LSI1030 0 A0> |
|-------------------------------------------------------------|
* * * Field Descriptions * * *
Adapter Indicates the specific family of LSI Logic Host Bus Adapters.
PCI Bus Indicates the PCI Bus number (range 0x00 - 0xFF, 0 - 255 decimal)
assigned by the system BIOS to an adapter.
Dev/Func Indicates the PCI Device/Function assigned by the System BIOS to
an adapter.
An 8-bit value mapped as follows:
Bit # 7 6 5 4 3 2 1 0
|___________| |_____|
| |> Bits 2-0: Function (range 0 - 7)
|> Bits 7-3: Device (range 0x00 - 0x1F, 0 - 31 decimal).
Boot Order Specifies the relative boot order (0 to 3) of an adapter.
- : decreases an adapter's relative boot order.
+ : increases an adapter's relative boot order.
Current Indicates whether an adapter in the boot list was enabled during
Status the most recent boot. Disabled adapters and their attached devices
are ignored by the Fusion-MPT PCI SCSI BIOS, they are still visible
to the Configuration Utility.
Next Boot Specifies whether to enable an adapter upon the next boot. The
Fusion-MPT SCSI BIOS ignores disabled adapters and their attached
devices although they are still visible to the Configuration
Utility.
* * * * * * * * * * Global Properties * * * * * * * * * *
The Global Properties option on the Main Menu allows you to set Display
and Video modes as well as a pause if an alert message has been displayed.
Here is an example of the Global Properties Menu:
|----------------------------------------------------------------------|
| LSI Logic MPT SCSI Setup Utility Version MPT -x.xx |
| |
| Global Properties |
| |
| Pause When Boot Alert Displayed [Yes] |
| Boot Information Display Mode [Verbose] |
| Negotiate with devices [Supported] |
| Video Mode [Color] |
| Support Interrupt [Hook interrupt, the Default |
| Disable Integrated RAID [No] |
| |
| <Restore Defaults> |
|----------------------------------------------------------------------|
|
* * * Field Descriptions * * *
Pause When Boot Alert Displayed
This option specifies whether to pause for user acknowledgement after
displaying an alert message during boot. The Boot Alert setting can be
either No or Yes.
To continue after displaying a message, specify No.
To wait for any key after displaying a message, specify Yes.
Boot Information Display Mode
This option specifies the information display mode of the BIOS during
boot. It controls how much information about adapters and devices
are displayed during boot. The Display Mode setting can be either Terse
or Verbose.
To display minimum information, specify Terse mode.
To display detailed information, specify Verbose mode.
Negotiate with devices
This option sets the default value for synchronous and wide
negotiations with specified devices. Options are: All, None, or
Supported.
Video Mode
This option specifies the default video mode for the Configuration
Utility. The Video Mode setting can be either Color or Monochrome. The
monochrome setting enhances readability on a monochrome monitor.
Support Interrupt
This option allows the ability to prevent a hook on INT40, if required.
Disable Integrated RAID
This option tells the firmware not to do a bus scan searching for RAID
member devices. It also disables configuration of RAID arrays in the
BIOS.
<Restore Defaults>
Press Enter to obtain default settings.
* * * * * * * * * Adapter Properties * * * * * * * * * *
The Adapter Properties Menu allows you to view and modify adapter settings.
It also provides access to an adapter's device settings. Here is an
example of the Adapter Properties Menu:
|--------------------------------------------------------------|
| LSI Logic MPT SCSI Setup Utility Version MPTBIOS -x.xx |
| |
| Adapter Properties |
| |
| Adapter PCI Dev/ |
| Bus Func |
| LSI1030 0 60 |
| |
| <Device Properties> |
| <RAID Properties> <Synchronize Whole Mirror> |
| Host SCSI ID [ 7] |
| SCSI Bus Scan Order [Low to High (0..Max)] |
| Removable Media Support [None] |
| CHS Mapping [SCSI Plug and Play Mapping] |
| Spinup Delay (Secs) [ 2] |
| Secondary Cluster Server [No] |
| Termination Control [Auto] |
| <Restore Defaults> |
|--------------------------------------------------------------|
* * * Field Descriptions * * *
<Device Properties>
To view and modify device properties, press Enter.
<RAID Properties>
To view, create/delete, and/or configure RAID arrays, press Enter.
<Synchronize Whole Mirror>
This copies the data from the primary copy of the mirrored array to the
secondary copy.
Host SCSI ID
This field indicates the SCSI identifier of an adapter [0-7] or [0-15].
It is recommended that this field be set to the highest priority SCSI
identifier, which is 7.
Note: 8-bit SCSI devices cannot see identifiers greater than 7.
SCSI Bus Scan Order
This field indicates the order in which to scan SCSI identifiers on an
adapter. Changing this item will affect drive letter assignment(s) if more
than one device is attached to an adapter.
Note: Changing this item may conflict with an operating system that
automatically assigns drive order.
Removable Media Support
This field specifies the removable media support option for an adapter.
Three settings are allowed:
None indicates no removable media support whether the drive is selected as
first (BBS), or is first in the scan order (non-BBS).
Boot Drive Only provides removable media support for a removable hard drive
if it is first in the scan order.
With Media Installed provides removable media regardless of the drive
ordering.
CHS Mapping
This field defines how the Cylinder Head Sector values are mapped onto a disk
without pre-existing partition information. CHS Mapping allows two settings:
SCSI Plug and Play Mapping (default value) and Alternate CHS Mapping.
SCSI Plug and Play Mapping automatically determines the most efficient
and compatible mapping.
Alternate CHS Mapping utilizes an alternate, possibly less efficient mapping
that may be required if a device is moved between adapters from different
vendors.
Note: Neither of these options has any effect after a disk has been
partitioned using the FDISK command. To change the CHS Mapping on a
partitioned disk, use FDISK command to delete all partitions. Then
reboot the system to clear memory or the old partitioning data will
be reused, thus nullifying the previous operation.
CAUTION: Use care to ensure that the correct disk is the target of an
FDISK command.
Spinup Delay (Secs)
This field indicates the number of seconds to wait between spinups of
devices attached to an adapter. Staggered spinups will balance the total
electrical current load on the system during boot. The default value is 2
seconds with choices between 1 and 10 seconds.
Secondary Cluster Server
This field indicates whether an adapter has one or more devices attached
that are shared with one or more other adapters and therefore, the
Fusion-MPT PCI SCSI BIOS should avoid SCSI Bus resets as much as possible.
This option allows you to enable an adapter to join a cluster of
adapters without doing any SCSI bus resets. This is a requirement for the
Microsoft Cluster Server. The default value is No with an alternate option
of Yes.
Termination Control
This field indicates whether an adapter has automatic termination control,
and if so, its current status. Two settings are:
Auto : The adapter automatically determines whether it should
enable or disable its termination.
Off : Termination at the adapter is off, the devices at the
ends of the SCSI bus must terminate the bus.
Note: If Auto is grayed out, it means that termination is automatic, not
programmable.
Restore Defaults
To obtain default settings, press Enter.
* * * * * * * * * * Device Properties * * * * * * * * * *
The Device Properties screen provides viewing and updating of individual
device settings for an adapter.
Changing a setting for the host device (for example, SCSI ID 7) changes
the setting for all devices. Here is an example of the Device Properties
screen:
|----------------------------------------------------------------------------|
| LSI Logic MPT SCSI Setup Utility Version MPT -x.xx |
| |
| |
| SCSI Device Identifier MB/sec MT/sec Data Scan Scan Dis- |
| ID Width Id LUNs > 0 connect |
| 0 - [160] [80] [16] [Yes] [Yes] [On] |
| 1 - [160] [80] [16] [Yes] [Yes] [On] |
| 2 - [160] [80] [16] [Yes] [Yes] [On] |
| 3 SEAGATE ST31055N [160] [80] [16] [Yes] [Yes] [On] |
| 4 - [160] [80] [16] [Yes] [Yes] [On] |
| 5 - [160] [80] [16] [Yes] [Yes] [On] |
| 6 - [160] [80] [16] [Yes] [Yes] [On] |
| 7 LSI1030 [160] [80] [16] [Yes] [Yes] [On] |
| 8 - [160] [80] [16] [Yes] [Yes] [On] |
| 9 - [160] [80] [16] [Yes] [Yes] [On] |
| 10 - [160] [80] [16] [Yes] [Yes] [On] |
| 11 - [160] [80] [16] [Yes] [Yes] [On] |
| 12 - [160] [80] [16] [Yes] [Yes] [On] |
| 13 - [160] [80] [16] [Yes] [Yes] [On] |
| 14 - [160] [80] [16] [Yes] [Yes] [On] |
| 15 - [160] [80] [16] [Yes] [Yes] [On] |
| << Scroll Indicator >> |
| |
| SCSI Device Identifier SCSI Queue Boot Restore |
| ID Timeout Tags Choice Defaults |
| 0 - < 10> [On] [No] <Defaults> |
| 1 - < 10> [On] [No] <Defaults> |
| 2 - < 10> [On] [No] <Defaults> |
| 3 SEAGATE ST31055N < 10> [On] [No] <Defaults> |
| 4 - < 10> [On] [No] <Defaults> |
| 5 - < 10> [On] [No] <Defaults> |
| 6 - < 10> [On] [No] <Defaults> |
| 7 LSI1030 < 10> [On] [No] <Defaults> |
| 8 - < 10> [On] [No] <Defaults> |
| 9 - < 10> [On] [No] <Defaults> |
| 10 - < 10> [On] [No] <Defaults> |
| 11 - < 10> [On] [No] <Defaults> |
| 12 - < 10> [On] [No] <Defaults> |
| 13 - < 10> [On] [No] <Defaults> |
| 14 - < 10> [On] [No] <Defaults> |
| 15 - < 10> [On] [No] <Defaults> |
| << Scroll Indicator >> |
|----------------------------------------------------------------------------|
* * * Field Descriptions * * *
SCSI ID
This field indicates the device's SCSI Identifier.
Device Identifier
This field indicates the ASCII device identifier string extracted from
the device's Inquiry Data.
Sync Rate
This field indicates the maximum synchronous data transfer rate, in
Mega Transfers per second.
Mega Transfers/ Data Data Synchronous
Second Width= 8 Width=16 Period nsec
Mbytes/s Mbytes/s
--------------- -------- -------- -----------
0=Async 0=Async 0=Async 0=Async
5 5 10 200
10 10 20 100
20 20 40 50
40 40 80 25
Data Width
This field indicates the maximum data width in bits.
Scan ID
This field indicates whether to scan for this SCSI identifier at boot time.
This item can be used to ignore a device and to decrease boot time by
disabling the inquiry of unused SCSI identifiers.
Set this option to "No" if there is a device that you do not want to be
available to the system. Also, on a bus with only a few devices attached,
the user can speed up boot time by changing this setting to "No" for all
unused SCSI IDs.
Scan LUNs > 0
This field indicates whether to scan for LUNs greater than zero for a
device. LUN zero is always queried. This option should be used if a
multi-LUN device responds to unoccupied LUNs or if it is desired to reduce
the visibility of a multi-LUN device to LUN zero only.
Set this option to "No" if you have problems with a device that responds to
all LUNs whether they are occupied or not. Also, if a SCSI device with
multiple LUNs exists on your system but you do not want all of those LUNs to
be available to the system, then set this option to "No." This will limit
the scan to LUN 0 only.
Disconnect
This field indicates whether to allow a device to disconnect during SCSI
operations. Some (mostly newer) devices run faster with disconnect enabled,
while some (mostly older) devices run faster with disconnect disabled.
SCSI Timeout
This field indicates the maximum amount of time [0 to 9999] in seconds to
wait for a SCSI operation to complete.
Since timeouts provide a safeguard that allows the system to recover
should an operation fail, it is recommended that a value greater than
zero be used. A value of zero allows unlimited time for an operation
to complete and could result in the system hanging (waiting forever)
should an operation fail.
Press Enter, type in a value, and then press Enter again to specify a new
timeout value.
Queue Tags
This field indicates whether to allow the use of queue tags for a device.
Currently the BIOS does not use queue tags. This item specifies queue tag
control to higher level device drivers.
Boot Choice
This field indicates whether this device may possibly be selected as the
boot device. This option is only applicable to devices attached to adapter
number zero (in the boot list) on non-BBS systems. It provides primitive BBS
flexibility to non-BBS systems.
Restore Defaults
Press Enter to obtain default settings.
* * * * * * * RAID Properties * * * * * * * * * * * * * *
The RAID Properties screen initially comes up listing all possible SCSI IDs on
the Adapter SCSI Channel. This allows the user to select disks on this channel
to be members of a Mirrored array. Mirroring provides protection against data
loss by keeping two copies of the data stored on separate disks.
|-------------------------------------------------------------------------------|
| LSI Logic MPT SCSI Setup Utility Version MPT -x.xx |
| |
| RAID Properties Array: -- SCSI ID: -- Size(MB): ------ |
| |
| SCSI Device Identifier Array Hot Status Predict Size |
| ID Disk? Spare Failure (MB) |
| 0 SEAGATE ST39103LW 002 [No] [No] ----------- --- 8683 |
| 1 SEAGATE ST39103LW 002 [No] [No] ----------- --- 8683 |
| 2 SEAGATE ST39103LW 002 [No] [No] ----------- --- 8683 |
| 3 - [No] [No] ----------- --- ------ |
| 4 - [No] [No] ----------- --- ------ |
| 5 - [No] [No] ----------- --- ------ |
| 6 - [No] [No] ----------- --- ------ |
| 7 LSI1030 [No] [No] ----------- --- ------ |
| 8 - [No] [No] ----------- --- ------ |
| 9 - [No] [No] ----------- --- ------ |
| 10 - [No] [No] ----------- --- ------ |
| 11 - [No] [No] ----------- --- ------ |
| 12 - [No] [No] ----------- --- ------ |
| 13 - [No] [No] ----------- --- ------ |
| 14 - [No] [No] ----------- --- ------ |
| 15 - [No] [No] ----------- --- ------ |
|-------------------------------------------------------------------------------| |
Array:
There are two different mirrored configurations: IM and 1E.
Integrated Mirroring(IM) is a simple sector-to-sector physical mirror of
one drive to another drive. This type has two members(Not including hot spare).
IBM 1E is the second type and has a striped layout with each stripe unit
having a secondary(or alternate) copy stored on a different disk. This type
is used when there are more than two active members in RAID array.
SCSI ID:
The SCSI ID that the Operating system or application addresses the array.
Size(MB):
Size of the array.
Array Disk?
The user selects a minimum of two disks under this column. A
maximum of six disks can be selected. Five is the maximum if a hot spare
has been selected.
Hot Spare
The user can optionally select a single hot spare. The Hot Spare disk
provides additional protection by automatically replacing an array member
when it fails.
Status
This give the status of each physical disk in the array.
Predict Failure
This tells whether SMART has determined that the disk will fail in the
near future.
Size
This shows the physical size of the disk when not an array member. When
part of an array it shows the size used for the array. The later will be
smaller because when the array is created the size is rounded down to
factor in disk size variances within same disk class.
Putting existing Data into a RAID array.
If the user wants to mirror a disk containing existing data, the user needs
to select the disk with data to be retained first and it will become the
primary copy of an Integrated Mirrored array. When the first disk is
selected the BIOS configuration utility prompts the user to either Keep
Data or Erase Disk. Hit F3 to keep data. Only IM arrays can be created to
keep previous data.
Saving Configuration or Exiting the RAID Properties Screen
If the user is done with this screen then the ESC key should be pressed. If
changes were made then the user will be given a choice to save or discard
the configuration. Saving the configuration will create the array.
Diagnostics Mode
Before the array is created the user can press F4 key to display diagnostic
codes under the Size column for each device on the system. These codes tell
why the configuration utility has disabled selection of some disks. A Disk
may be disabled for the following reasons:
1 - Problem with reading disk serial number
2 - Disk does not support SMART
3 - Unused
4 - Disk does not support wide data, synchrounous mode, or queue tagging
5 - User disabled disconnects or queue tags for device(Device Properties)
6 - Unused
7 - Disk not big enough to mirror primary disk
8 - Unused
9 - Unused
10- Disk does not have 512 byte sector size
11- Incorrect device type
12- Hot Spare selection not big enough to be used as an array disk
13- Maximum disks already specified or Maximum array size would be exceeded
After an array has been created the user can do the following:
<Delete Array>
Deletes the array currently displayed in RAID Properties screen.
<Add/Delete Hot Spare>
Allows adding a hot spare to an existing volume as long as no hot spares
are defined. Also allows deleting a hot spare and leaving the array otherwise
operational.
<Next Array>
This choice is enabled for illegal configuration situation where there are
more than one array on this physical adapter. The RAID Properties screen
allows display of one array at a time. This choice allows the user to display
and operate on next array found.
<Activate Array>
If there are two arrays on a physical adapter, this option allows the user
to tell the RAID firmware which array should be active. Only one
array can be active at a time per physical adapter. Activating an array
also causes all the remaining arrays found on the physical adapter to be
inactivated.
* * * * * * Quitting the SCSI BIOS Configuration Utility * * * * * *
Since some changes only take effect after your system reboots, it is
important that you exit this configuration utility properly. To exit, press
Esc (Escape key) and respond to the verification prompts that follow.
Important: If you reboot the system without properly exiting from this
utility, some changes may not take effect.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.