VERSION.TXT Driver File Contents (VGA_Intel_6.14.10.3553_XPx86.zip)

    Intel(R) Extreme Graphics Driver for Win2K&XP - WW -
    VERSION      : 6.14.10.3553
    BUILD ID     : IDG0NC1W
Sopport Chip
    Intel(R) 845G Chipset                                  
    Intel(R) 855GM Chipset                                 
    Intel(R) 855PM Chipset                                 
    Intel(R) 845GL Chipset                                 
    Intel(R) 865G Chipset                                  
    Intel(R) 845GE Chipset  
    Intel(R) 852GM Chipset  
    Intel(R) 855GME Chipset                  
    Intel(R) 845GV Chipset  
    Intel(R) 852GME Chipset 
    Intel(R) 855GME Chipset 
    Intel(R) 845GV Chipset  
    Intel(R) 852GME Chipset 

-- HOW TO CLEAN INSTALL   
   1.Unzip the package files. 
   2.Double click the SETUP.EXE to run install.
                          
-- HOW TO OVER INSTALL    
   1.It is the same as clean install.

-- HOW TO SILENT INSTALL
   1.Run SETUP -s    

-- HOW TO UNATTENDED INSTALL
   1. Run in silent mode.
	SETUP -s  
   2. Forces a system reboot after the installation completes.
	SETUP -s -b
   3. Suppresses the display of the license agreement screen.
	SETUP -s -nolic

-- HOW TO VERIFYING THE INSTALLATION OF THE SOFTWARE
   1.Click on the "My Computer" icon, then click on the
     "Control Panel" icon, and then click on the "System"
     icon.

   2.Select the "Hardware" tab and then click on the
     "Device Manager..." button.

   3.Select the "Display Adapters" icon. The Intel Graphics
     Driver should be listed. If not, the driver is not
     installed correctly. To check the version of the driver,
     refer to the section below.

-- HOW TO IDENTIFYING THE SOFTWARE VERSION NUMBER
   1.Click on the "My Computer" icon, then click on the
     "Control Panel" icon, and then click on the "Display"
     icon.

   2.Select the "Settings" tab and then click on the
     "Advanced" button.

   3.Select the "Intel(R) Graphics Technology" tab. The
     graphics driver version should be listed on this screen.

-- HOW TO UNINSTALLING THE SOFTWARE
   NOTE: This procedure assumes the above installation process
   was successful. This uninstallation procedure is specific
   only to the version of the driver and installation files
   included in this package.

   1.Click on the "My Computer" icon, then click on the
     "Control Panel" icon, and then click on the "Add-remove
     Programs" icon.

   2.Select on the "Intel Extreme Graphics Driver" tab and then
     click on the "Remove" button. 

   3.Click on the "OK" button and then click on the "Yes"
     button to reboot.

-- SPECIAL NOTES OR RESTRICTIONS/CAUTIONS:
To properly install the driver for Windows XP, the following steps must be taken.  
This will be fixed in future drivers.
Procedure to correctly load drivers on Windows XP ( HaveDisk ):
1) Go to Device Manager and install drivers as is currently done
2) Wait for driver install to complete. DO NOT click Finish yet or reboot system yet.
3) Minimize the Device Manager window so that any hidden New Hardware Found windows are visible.
3) This New Hardware found windows should now be displayed on the Desktop ( or on top of the 
   Device Manager window). This may take a few seconds to show up.
4) Make sure to respond to each New Hardware prompt. Click on Automatic Install. DO NOT point to 
   any directory path for these drivers. Wait for completion before continuing. (In the event
   that the new hardware prompt does not pop up, finish the driver installation and the new 
   hardware prompt should be seen on the subsequent re-boot.) 
5) ALL New Hardware prompts must be completed before clicking Finish for install. The following 
   Found New Hardware prompt windows should be seen:
   1) SoftBios
   2) KCH
   3) All installed AIM modules
Please be sure that you see New Hardware Found prompts. At a minimum, you should always see two 
( SoftBios, KCH). If you do not see these, and click Finish to complete the install, subsequent
 boot will be to VGA.  


Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web5, load: 1.44