releases.txt Driver File Contents (Lan_Broadcom_v10.78.0.0_XPx86.zip)

         Release Note for BCM5705 Family BOOT Code Firmware
         ==================================================
                    5705, 5705f, 5782, 5788, 5901
                    
-------------------------                    
Version 3.27 ---- 7/8/05
-------------------------
1. Removed NIC cut off delay time feature

  Problem:
    In NIC, when firmware detects VMain is not present and WoL is diabled, 
    it will cut off power by using GPIO 1 to generate a rising edge.
    
    This debug feature is to delay the time before cutting off the power. 
    The user had choice of delaying 250ms, 150ms, 50ms, or 0ms before cut 
    off power. By default, the delay time was 250ms. However, this feature 
    not only appears to be no value in final product but also to cause 
    excessive power comsumption before cutting off power, it is better to
    remove this feature. 
    
  Fix:
    Removed this feature.
    
  Impact:
    Changing VAUX cut off delay value in NVRAM configuration (offset 0xc4, [23:24])
    will take no effect.
                  
2. Added SST non-buffered flash (SST45VF010/SST45F512) support

   Enhancement:
     Added SST 1MB non-buffer support. Due to buffering problem,
     no VPD write is supported.
   
   The following is the supported NVRAM summary:
     
   SCLK: Bit 1,  Buffered Mode,  internal pull-down
   CS:   Bit 0,  Flash Mode,     internal pull-down

    [SCLK,CS]    Device         Write         Memo         
   ------------- -------------- ----- ----------------------------
        00       AT24C512        Yes  SEEPROM, AT24Cxxx, any size
        11       AT45DB011B      Yes  Atmel Buffered 1MB Flash
        01       SST SST45VF010  No   SST Non-Buffered 1MB Flash
        01       SST SST45VF512  No   SST Non-Buffered 512KB Flash
        
3. Removed disabling WoL procedure

   Enhancement:
     Earlier bootcode used to be disabling WoL if the device is in
     D3 state while VMain presents. 
     
   Cause:
     In the old days, there was no good communication defined between
     driver and bootcode for WoL initialization. One good way for
     bootcode to determine if driver present or not was by looking at
     power state. Only driver could place the device into D3 state
     while VMain present. In order to support old driver without WoL 
     handshake, bootcode was not arming WoL if D3 state was detected
     while VMain present. For 5705 family devices, all driver has WoL
     handshake defined, therefore, this line was no longer needed.
     
        
-------------------------                    
Version 3.26 ---- 6/16/04
-------------------------
  1. Added Capacitive Coupling feature support CQ#10394
  
    Enhancement:
      Added Capacitive Coupling (CC) support. Defined a new configuration in
      hw_config in nvram. When CC is enable in the NVRAM, the PHY must be 
      reconfigured by setting bit 10 in register 0x18, shadow register 100b. 
      Setting this bit configures the link pulse transmitter to function 
      properly in a CC application. After enabling CC in the PHY, the link 
      must be reset and auto-negotiation restarted.
  
    Note:
      Bootcode will only configure phy to this mode upon cold reset.
      When driver reset (with reset signature), bootcode will not touch phy 
      registers. 
      
-------------------------                    
Version 3.25 ---- 5/5/04
-------------------------                    
  1. Added blinking feature when loading ASF code failed.

    Problem:
      Loading ASF failure case has been seen on certain system.
  
    Enhancement:
      In order to indicate loading ASF failed, blinking LED feature
      has been added. 
    
  2. Enable PXE only when PXE image exists

    Problem:
      System may hang when PXE is enabled without PXE image.
  
    Cause:
      Due to user error, it is possible PXE is enabled without image.
      Bootcode was enabling PXE based on enable/disable. As result,
      bootcode is returning garbage.
    
    Fix:
      Advertise PXE only when there is an image and PXE is enabled.
        
-------------------------                    
Version 3.24 (4/19/04)
-------------------------                    

  1. Applied the workaround for higher BER problem

    Problem: 
      On certain corners, bit-error-rate(BER) was higher then desired
      when cable length was 70m or less.
  
    Workedaround:
      By increasing hybrid bias current can reduce the BER. 
    
-------------------------                    
Version 3.23:
-------------------------                    

  1. Fixed ASF/Driver handshake problem

    Problem:
      Today, we are using the shared memory last_driver_state, 0xc04, as 
      parameter for reset. last_driver_state got cleared by bootcode 
      upon reset.
      
      For 5705, driver deposit this parameter after GRC reset; therefore the
      symton is not showing up. However, by doing this, there will be a race
      condition between driver write and ASF code read.
     
      The proper way to fix this should be done in both driver and firmware:
      Firmware should change to not to clear this field upon reset.
      Driver should deposit command prior to GRC reset; however this will not
      work with older firmware since the command get cleared upon reset;
      therefore, driver should deposit the command one more time after reset
      like before to prevent the device running with old firmware. 
 
    Cause:
      Upon reset, bootcode is designed to initialize all shared memory 
      between 0xb54-0xc28 to zero. Originally, when last_driver_state field 
      was defined, it was only used for ASF self resetting purpose; therefore, 
      the code has been changed to: "if the last_driver_state (0xc04) contains 
      CPU_RESET (0x40), then preserve this value." Any other value was cleared 
      to zero. When ASF code sees the value "CPU_RESET", it knows the reset 
      was initiated by ASF code itself and will know how to handle the reset. 
      This changed was made in more than two years ago, Dec. 92. and it was 
      working since.
      Today, we defined more usage for last_driver_state parameter. However, 
      since the bootcode will only preserve the value for CPU_RESET (0x40), 
      any other parameter was zeroed.
      The reason, the problem never showed up until now was probably because, 
      driver was writing the parameter after bootcode initialize shared memory 
      to zero and before ASF was fully up and running. Now, we are trying to 
      change the driver code to deposit signature and parameter before GRC reset, 
      the problem showed up. 
 
    fix:
      Change bootcode to preserve any value in last_driver_state, 0xc04. 

  2. Turn core clock to slow speed in WoL
   
    Problem:
      When bootcode going to WoL mode. The core clock was not slowed
      Down.
      
    Cause:
      5705/Shasta clock control bits are different from 5703 or 5704 devices
      and it was using 5703 bits to control core clock. 
      
    Fix:
      Changed the code to program correct bits to slow clock to save power
      under WoL mode (VAUX power only mode). 
      
    Note:
      This bug does not cause any functional problem. Fixing this problem 
      will give us a better power consumption under WoL mode. 
              
Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web3, load: 1.74