PROTOCOL.INI Driver File Contents (Lan_3com_04.08.0000.0_Xpx86.zip)

    DriverName = "EL90X$"
;
; below are examples and explanations of some of the keywords supported by
; the 3C90X NDIS 2.01 driver.  most of the lines are simply comments.  the
; marked with "-->" are lines that can be edited (removing the ";-->" and
; lines replacing it with spaces, and modifying the right hand side as
; appropriate.
;
; MAXTRANSMITS=n, n=6..50, specifies the number of transmits which can be
; queued up by the driver when the TxFIFO is full or the adapter is otherwise
; busy.  When we run out of queue entries, an OUT_OF_RESOURCES error will be
; returned to the protocol on a transmit attempt.  Most protocols will handle
; running out of resources will little performance degradation.  However,
; some implementations will drop packets and consequently lower performance
; if OUT_OF_RESOURCES is returned too often.  The default value is 6, which
; should be sufficient for most cases, and is adequate for window sizes up to
; about 6 or so.  On a heavily loaded server with a lot of active connections,
; you may want to increase this number since with large windows on multiple
; active connections you may need a bigger transmit queue to handle them all.
; Each queue entry takes about 128 bytes of memory, so increasing this number
; will increase the resident size of the driver.
;
MAXTRANSMITS=40
;
; NETADDRESS allows the user to configure the network address of the adapter,
; rather than using the one in EEProm.	If not specified the address on the
; adapter will be used.  If specified, the right hand side must be exactly
; 12 hex ASCII characters which will be converted to the network address.
; The only restrictions we impose is that the address not have the multicast
; bit set (an odd number in the second digit) and the network address have
; bit one of the most significant byte of the address set.  This bit
; signifies a locally administered address.
;
;-->NETADDRESS="02608C123456"
;
;
; SLOT=n, n=0..31 specifies the specific slot number to look for a 3C90X
; adapter.  In the absence of this keyword the driver will search all slots
; for a 3c90x adapter, so it isn't required unless there are multiple 3C90X
; adapters in the computer.  For PCI the "SLOT=n" parameter is actually a
; device number.  Usually device 0 is on the motherboard, and the "slots"
; start around 8 or so, but this varies from computer to computer.  The best
; way to determine what number to use is to look at the slot number displayed
; by the 3C90XCFG.EXE program for a given adapter.  Note: if BUSNO is not
; specified, but SLOT is, we will search the specified SLOT on all PCI busses
; (0..7) in turn.
;
;-->SLOT=8
;
; BUSNO=n, n=0..7 specifies the PCI bus number to search for the 3C90X
; adapter.  In most computers today there is only a single PCI bus, number 0.
; However, the PCI architecture allow for multiple PCI busses.	If this
; keyword isn't specified, the driver will search all busses for a
; 3C90X adapter, so this keyword isn't required unless there are multiple
; 3C90X adapters in the computer.
;
;-->BUSNO=0


Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web5, load: 1.07