===========================
R E L E A S E N O T E S
===========================
Broadcom Advanced Server Program (BASP) Driver
for Linux 2.2.x and 2.4.x kernel
Version 2.0.5
Copyright (c) 2000-2001 Broadcom Corporation
All rights reserved.
November 14, 2001
Table of Contents
-----------------
1. Overview
2. Limitation
3. Installation
4. Install - TAR archive
5. Install - RPM package
6. Files
7. Configuration - Red Hat Distribution
8. Configuration and Startup for Other Linux Distribution
9. Startup scripts - Red Hat distributions
10. Configuration scripts - Redhat Distributions
11. Broadcom NICE patches
12. Uninstall - RPM package
13. Removal of physical interface in Generic Trunking mode
14. Known Problems
15. Logs
1. Overview
-----------
BASP is a kernel module designed for Linux 2.2.x and 2.4.x kernels that
provides load-balancing, fault-tolerance, and VLAN features. These features
are provided by creating teams that consist of multiple NIC interfaces.
A team can consist of 1 to 8 NIC interfaces and each interface can be
designated primary or hot-standby. All primary NIC interfaces in a team will
participate in Load-balancing operations by sending and receiving a
portion of the total traffic. Hot-standby interfaces will take over in the
event that all primary interfaces have lost their links. VLANs can be
added to a team to allow multiple VLANs with different VLAN IDs. A
virtual device is created for each VLAN added.
BASP supports Smart Load-balance (SLB<tm>) and Generic trunking. In
SLB mode, all the NIC drivers must support Broadcom NIC Extension (NICE).
In this release, several NIC drivers patched with NICE are included.
SLB mode works with all Ethernet switches without configuring the switch
ports to any special trunking mode. Only IP traffic will be load-balanced
in both inbound and outbound directions. The Generic trunking mode does
not require NICE and can work with any NIC, however, it requires the
Ethernet switch to support the technology and be properly configured.
This mode is protocol-independent and all traffic should be load-balanced
and fault-tolerant.
2. Limitation
-------------
BASP supports Red Hat 6.2, 7.0, 7.1 and 7.2 Beta. The following
installation procedures work with these distributions. BASP has also
been tested on SuSE 7.1 & 7.2, Caldera 2.4 & 3.1, Turbo Linux 6.5 and
Mandrake 8.0. Minor modification to the Makefile may be required if
problems are experienced when compiling BASP on other i386 Linux
distributions.
BASP also supports Red Hat Linux 7.1 for IA-64 architecture and has
been tested on Redhat Linux 7.2 Beta for IA-64.
VLANs are only supported by Broadcom NetXtreme Gigabit Ethernet. As
opposed to VLANs support in other platforms, e.g. Windows and Netware,
VLANs are not supported by Alteon Acenic driver (acenic.c).
3. Installation
---------------
For users of Redhat 6.2, 7.0, 7.1 and 7.2 (i386 and IA-64), follow
instructions in "Install - RPM package" section.
For users of other Linux i386 and IA-64 distribution, follow
instructions in "Install - TAR archive" section.
4. Install - TAR archive
------------------------
BASP for Linux is shipped in mixed forms, where the platform and
kernel specific files are in source code, and the core file is in object
form. Three packages are shipped in this release: two tar archives and
two RPM package.
"basplnx-{version}.i386.tgz" is the tar archive for i386 platform, and
"basplnx-{version}.ia64.tgz" is the tar archive for IA-64 platform.
To uncompress and expand the tar archive, run
% tar xvfz basplnx-{version}.{arch}.tgz
The installation process involves the following steps:
(1) Configure the major device number for BASP configuration. The default
major number is 250 and it can be changed by modifying "Makefile".
(2) To build kernel module, "basp.o",
% make
Note that the Make process will automatically build the correct module
for different kernel options, e.g. symbol versioning and SMP support.
There is NO need to define -DMODVERSIONS in the Makefile.
(3) To create device file and to copy files,
% make install
(4) To update the module reference,
% depmod -a
(5) To load the driver,
% insmod basp
Note-1) If when loading the BASP module, an error message regarding
"invalid IO or IRQ parameters" are observed, you will need to
configure the major device number for BASP configuration by
following step (1) above.
(6) Follow the "Configuration and Startup for Other Linux Distribution"
section to set up the teams.
5. Install - RPM package
------------------------
(1) To install the RPM source package, run
% rpm -i basplnx-{version}.src.{arch}.rpm
(2) Change directory to the RPM path and build the binary driver for the
kernel
% cd /usr/src/redhat
% rpm -bb SPECS/basplnx.spec
Note that the RPM path is different for different Linux distributions.
(3) Install the newly built package
% rpm -i RPMS/i386/basplnx-{version}.{arch}.rpm
The driver and other required files will be automatically installed.
(4) To load the driver,
% insmod basp
(5) Follow the Configuration section to set up the teams.
6. Files
--------
Makefile makefile
baspcfg precompiled configuration utility
bcmtype.h commonly use type header file
blf.c BASP module entry points
blf.h ioctl interface
blfcore.h core interface
blfcore.o pre-compiled core object
blfopt.h automatic generated header file by Make
blfver.h version header file
nicext.h NICE header file
pal.c platform abstraction implementation
pal.h header for paltform abstraction
release.txt this file
nice-2.2.16 contains NICE enabled driver source code
scripts contains sample scripts
scripts/basp init script, goes to /etc/rc.d/init.d
scripts/baspteam start/stop script, goes to /etc/basp
scripts/baspif start/stop network i/f, goes to /etc/basp
scripts/team-sample sample script of SLB team with 3 NICs
scripts/team-gec sample script of GEC team with 3 NICs
scripts/team-vlan sample script of SLB team with 2 VLANs
basp.4 man page
baspcfg.8 man page for baspcfg utility
7. Configuration - Red Hat Distribution
---------------------------------------
The BASP distribution includes an utility program and several scripts for
team configuration. Following steps for Red Hat Linux distributions only.
Most of the steps are only required to be performed after the first time
installation. Step 2 "Modify the configuration script" should be performed
whenever there is any change to the team configuration.
For users of other Linux distributions, follow instructions in the
"baspcfg" section.
The configuration process involves the following steps:
(1) Copy a configuration script from "/etc/basp/samples" directory to
"/etc/basp" directory. Note the configuration script must be prefixed
with "team-".
(2) Modify the configuration script to
(a) change the team type
(b) add/delete physical network interfaces
(c) add/delete virtual network interfaces
The syntax of the configuration script can be found below. Note that
when configuring Teaming, at lease one Primary Adapter is required.
(3) Run "netconf" to configure the IP address of the virtual network
interface. It is important to manually enter the interface name,
i.e. sw0, when configuring the IP address. This is because the virtual
network interface, i.e. sw0, is not shown in the physical interface list.
Failure to enter the virtual interface name will result in missing
"ifcfg-" script in /etc/sysconfig/network-scripts directory. This script
is required to start the BASP team.
(4) Manually start the team for the first time,
% /etc/rc.d/init.d/basp start
Note that this step is only required for the first time installation.
The team configuration will be automatically started on subsequent
reboots.
Note that if not all the virtual network interfaces are configured
with IP address, there will be an error message in starting the
BASP team. When this happens, repeat step (3) to configure IP address
for all the virtual network interfaces.
Note-1) Forming multiple teams is possible by copying the sample files
into "/etc/basp/team-<name>" and modifying this file as
described in the sample file.
Note-2) In order to create more that one virtual interface (VLAN) for
each team, refer to the respective description section in the
sample files.
8. Configuration and Startup for Other Linux Distribution
---------------------------------------------------------
"baspcfg" is a command line tool to configure the BASP teams, add/remove
NICs and add/remove virtual devices. This tool, may be used to configure
your own startup script files. Please read your distribution specific
documentation for more information on your distributions's startup
procedure.
Following is the usage of this tool:
baspcfg v2.0.4 - Broadcom Advanced Server Program Configuration Utility
Copyright (c) 2000-2001 Broadcom Corporation. All rights reserved.
usage: baspcfg <commands>
commands:
addteam <tid> <type> <tname> -- create a team
delteam <tid> -- delete a team
addva <tid> <vlan_id> <vname> [macaddr]
-- add a virtual adapter to a team
delva <tid> <vlan_id> -- del a virtual adapter from a team
bind <tid> <role> <device> -- bind a physical adapter to a team
unbind <tid> <device> -- unbind a physical adapter from a team
show [tid] -- display team configurations
where
tid -- An unique ID for each team, starting from 0
type -- Team type: 0=SLB, 1=FEC/GEC
tname -- ASCII string of the team
vlan_id -- VLAN ID: from 1 to 4094, 0=untagged or no VLAN
vname -- ASCII string of the virtual device
macaddr -- MAC address (optional), e.g. 00:10:18:00:11:44
role -- Role of the physical device: 0=primary, 1=hot-standby
device -- ASCII string of the physical device, e.g. eth0
Following sample startup script should be used to start the BASP after
first time installation and configuration, or in the subsequent reboots.
#!/bin/bash
# load basp module
insmod basp
# create new team
baspcfg addteam 0 0 team-one
# bind physical interfaces / two primary one backup
baspcfg bind 0 0 eth0
baspcfg bind 0 0 eth1
baspcfg bind 0 1 eth2
# create the virtual interface
baspcfg addva 0 0 sw0
# bind ip address to virtual interface and initialize
ifconfig sw0 192.168.0.1 up
Note: Baspcfg command can only be executed in Super User mode only,
configure with other login mode will yield "Permission Denied. Must be
root to manage BASP" error message.
When configuring Teaming, at lease one Primary Adapter is required.
9. Startup scripts - Red Hat distributions
------------------------------------------
(1) basp
This script is intended to be installed in /etc/rc.d/init.d directory.
After copying the script, run "chkconfig --add basp". This script will be
executed at runlevel 2, 3, 4 and 5. When "basp" is run, it will search
the /etc/basp directory to list all the files with "team-" prefix, and
then it will invoke "baspteam" script to add or delete the teams. It
is normal that each "team-*" file in /etc/basp represents 1 team.
(2) baspteam
This script is called by "basp" script to add or delete a team.
To install, create "/etc/basp" directory and copy this script over.
To manually add a team:
% baspteam team-sample add
To delete a team:
% baspteam team-sample del
Note that "team-sample" is the configuration script.
(3) team-sample
This script contains a SLB team configuration with 3 NICs: eth0, eth1
and eth2. The team name is "TeamSample". All 3 NICs are primary. One
virtual interface is also created for this team and the name of the virtual
interface is "sw0". "sw0" is the device that "ifconfig" should be run
against to set up the IP address. VLANs are not enabled in this script.
This script and "team-gec" are intended to be customized. Refer to the
configuration scripts section for details. This script should be copied
to /etc/basp directory and retain the "team-" prefix.
(4) team-gec
This configuration script creates a GEC team with 3 network interfaces,
eth0, eth1 and eth2. The team name is "TeamGEC". All 3 NICs are primary.
One virtual interface is added to the team with the name "sw0" and
VLANs are not enabled.
This script and "team-sample" are intended to be customized. Refer to the
configuration scripts section for details. This script should be copied
to /etc/basp directory and retain the "team-" prefix.
10. Configuration scripts - Redhat Distributions
------------------------------------------------
Both "team-sample" and "team-gec" are configuration scripts that follow
the same syntax, as following
TEAM_ID: this number uniquely identifies a team.
TEAM_TYPE: 0 = SLB, 1 = Generic Trunking/GEC/FEC
TEAM_NAME: ascii name of the team
TEAM_PAx_NAME: ascii name of the physical interface x,
where x can be 0 to 7.
TEAM_PAx_ROLE: role of the physical interface x
0 = Primary, 1 = Hot-standby. This field
must be 0 for Generic Trunking/GEC/FEC
team.
TEAM_VAx_NAME: ascii name of the virtual interface x,
where x can be 0 to 63
TEAM_VAx_VLAN: 802.1Q VLAN ID of the virtual interface x.
For untagged virtual interface, i.e. without
VLAN enable, set it to 0. The valid VLAN ID
can be 0 to 4094.
Note: Teaming scripts are intended for Red Hat distributions ONLY,
use with other Linux distribution will causes ERROR.
11. Broadcom NICE patches
-------------------------
Also included in this release are network device drivers patched
with Broadcom NICE support. These drivers are originally taken from
the Linux 2.2.16 kernel distribution. To install patched drivers:
(1) Copy the Broadcom NICE header file, "nicext.h", to the appropriate
Linux kernel include directory, e.g.
% cp /usr/src/nice-2.2.16/nicext.h /usr/src/linux/include/linux
(2) Rename the original network device driver under the Linux kernel
source tree, "/usr/src/linux/drivers/net".
(3) Copy the patched drivers to the Linux kernel network driver source
directory, i.e. "/usr/src/linux/drivers/net".
(4) Follow the kernel rebuild instructions to configure kernel
support for these drivers, i.e.
% cd /usr/src/linux
% make config
(5) If the patched drivers are configured into the kernel, goto step (7).
If the patched drivers are configured as modules, goto step (6).
(6) In the case of supporting only the module version of these drivers,
it is possible to simply run the following to compile patched drivers
and to install them into the proper module directory:
% make modules
% make modules_install
There is no need to compile the complete kernel. Goto step (8).
(7) Rebuild the kernel to compile these patched drivers
% make clean
% make dep
% make
(8) Either reboot the system or unload/load the patched modules. Run
configuration scripts to test the patch.
12. Uninstall - RPM package
---------------------------
To uninstall RPM package,
% rpm -e basplnx
and to reboot the system,
% reboot
13. Removal of physical interface in Generic Trunking mode
----------------------------------------------------------
In Generic Trunking mode, all the physical and virtual interfaces
belonging to a team have the same MAC address. This MAC address is the same
address as that of the first physical interface bounded to the team. In
the case that this first physical interface is removed dynamically from the
team using "baspcfg" tool and bounded to the protocol directly, this could
lead to a duplicate MAC address problem on the network. Note that if the
removed physical interface does not participate in any traffic, there
will not be any problem.
To properly remove a physical interface in a Generic Trunking team, follow
the steps listed below:
(1) Backup the original team configuration script
% cp /etc/basp/team-gec /etc/basp/backup-gec
Note-1) "team-gec" is the name of the configuration script.
Note-2) "backup-gec" is the name of the backup script. The name of the
backup script must NOT be prefixed with "team-".
(2) Modify the team configuration script to remove the physical interface
(3) Stop the running team
% /etc/basp/baspif /etc/basp/backup-gec stop
% /etc/basp/baspteam /etc/basp/backup-gec del
(4) Re-start the team
% /etc/basp/baspteam /etc/basp/team-gec add
% /etc/basp/baspif /etc/basp/team-gec start
14. Known Problems
------------------
(1) We have identified that the network configuration utility, Yast2,
distributed with Suse Linux 7.0 and 7.1 failed to save the IP address
assigned to the virtual network interface. Following error message will
be seen when running the "basp" init script:
Adding basp team-example OK
Starting basp team-example FAILED
To activate the virtual network interface, enter following command:
% ifconfig sw0 172.16.10.10 up
Consult ifconfig(8) for details in manually configuring a network
interface.
(2) DHCP address problem
We have identified that there is incompatiblity between SLB and IP address
obtained via DHCP. In the lab, we have seen that the virtual network
interface lost the IP address after running for a period of time.
To solve the problem, always assign static IP address to the virtual
network interfaces.
15. Logs
--------
v2.0.5
- Fixed lock-up problem with 2.4 SMP kernel.
v2.0.4
- Enhanced install documentation for non-Red Hat distribution.
- Minor documentation changes.
- Corrected the error message displayed by "baspcfg" utility.
- Added removal of empty directories at RPM un-install time.
v2.0.3
- Changed default BASP management device to 250 to facilitate out of box
installation.
- Added access control to allow that only root can manage BASP. proc file
system is still visible to all users.
v2.0.2
- Added support to the Linux 2.4.2 kernel for IA-64 architecture.
v2.0.1
- Fixed the server hang problem caused by removing a physical interface
without first detaching from the team.
- Added proc fs support for reporting team configuration.
v1.2.2
- Enhanced "basp" init script to work with other Linux distrbutions.
- Fixed jumbo frame problem.
v1.2.1
- Added support to Redhat 7.1 release.
- Added man pages.
v1.2.0
- Added support to the Linux 2.4.0 kernel.
v1.1.13
- Added check to prevent the removal of the primary physical interface
in a generic trunking team. Such removal might cause duplicated MAC
addresses on the network.
v1.1.12
- Updated the release note.
v1.1.11
- Fixed the problem of adding the same virtual interface twice.
- Correctly attribute packet counters to the correct virtual interfaces
when VLAN is enabled.
v1.1.10
- Fixed the problem that invalid VLAN can be added but not removed.
- Add removing of BASP teams in RPM de-installation.
- Added usage and argument checking to basp script.
- Fixed the problem that init script fails with multiple teams.
- Fixed the problem in switching runlevels.
v1.1.9
- Enhanced RPM packaging support.
- Changed "basp" script to run at priority 11, which is right after
"network" script.
- Automatically detect the presence of "kgcc" and use "kgcc" to get
around Redhat 7.0 compiler problem.
- Added "baspif" script to start and stop network interfaces.
v1.1.8
- Added RPM packaging.
v1.1.7
- Fixed failure of server originated ping with VLAN enable.
- Fixed loss of network connection under heavy traffic on SMP system.
v1.1.6
- Changed both module and device name to "basp.o" and "/dev/basp"
respectively for consistency.
- Added startup scripts.
- Enhanced Generic Trunking support by automatically programing the MAC
addresses.
- Addressed VLAN deletion issue.
v1.1.5
- Fixed Generic Trunking problem.
- Improved error messages in runing baspcfg utility.
- Added Generic Trunking sample script.
v1.1.4
- Added "show" command in baspcfg to display team configurations and status.
- Improved module build process for MODVERSIONS and SMP kernel.
- Display module build options in syslog during module load time.
- Display blfcore.o version during module loading time.
- Major changes in Makefiles to improve the build process.
- Improved build documentation.
- Changed to new baspcfg usage to the release.txt.
- Added documentation to describe how to install NICE patched drivers.
v1.1.3
- Fixed pal_read_mii() function.
v1.1.2
- Fixed linux/if.h dependency problem which prevented BASP from detecting
NICE supported driver on older kernels.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.