README.TXT 07-20-2000 CDC
Flash BIOS version 1.40 for Portege 3440CT
=============================================================================
This BIOS is applicable to the following models:
Portege 3440CT
For purposes of this document, the term "Portege 3440CT"
is used to generically refer to all of the models listed above.
=============================================================================
This archive contains the following files:
README.TXT Installation/usage instructions in ASCII text format
README.COM Self-displaying version of installation/usage instructions
1319D140.EXE Self-extracting diskette image of BIOS install diskette
BIOFC04T.COM Flash BIOS 1.40 image for Portege 3440CT
(provided here for installation methods 2 and 3)
CHGBIOSA.EXE Flash BIOS update utility version 4.12
(provided here for installation methods 2 and 3)
INSTINFO.BAT DOS batch file that creates install disk and displays README
file
This BIOS version is Windows 2000 compatible and supports Plug and Play,
and ACPI functionality.
********************************** CAUTION! *********************************
*****************************************************************************
During the upgrading of your computers BIOS, if the computer loses power or
fails to complete the process of upgrading the BIOS, the existing BIOS in
the computer may become damaged. In the event of this occurring, the
F12 Installation Method, described below, can be used to recover from
this error condition.
If you are upgrading a number of computers with this BIOS, the F12
installation method is the quickest.
It is recommended that all PCMCIA cards be removed from the system prior to
upgrading the BIOS. Also advisable is removing the computer from an attached
DeskStation V or DeskStation V Plus or NoteDock Enhanced Port Replicator.
It is not unusual to see a CMOS error when you first reboot the computer after
installing the new BIOS. If you see this message on your screen, press F1 as
instructed. This displays the "TSETUP" screen. Press <End> to save the CMOS
data. You won't see the CMOS error again.
******************** BIOS INSTALLATION INSTRUCTIONS *************************
*****************************************************************************
There are three ways to install this BIOS version:
1) Use the bootable diskette that is automatically created by the Windows
UnZip process (Recommended)
2) At startup by holding down the F12 key.
3) Run CHGBIOSA.EXE at the command prompt.
*****************************************************************************
1) BOOT DISKETTE INSTALLATION METHOD (Recommended)
--------------------------------------------------
This release of the electronic distribution BIOS utilizes a self-extracting
ZIP file that, when run under Windows or Win-OS2, creates a bootable BIOS
installation diskette.
Since you're reading this, you were obviously able to extract the downloaded
file. If you also created the BIOS installation diskette as a part of the
extraction process, you're ready to follow the installation instructions
below.
If you didn't create the installation diskette during the extraction phase,
or if you extracted the downloaded file with PKUnZip or WinZip, you can
create the installation diskette by executing the INSTINFO program from the
DOS command prompt.
Install this BIOS using the following steps:
WINDOWS 95/98 or Windows NT 4.x:
o Close all open programs
o Insert the BIOS installation diskette into your diskette drive (A:)
o Click Start
o Click Shutdown
o Click the radio button next to "Restart the computer?"
o Click Yes
WINDOWS 3.x:
o Close all open programs
o From Program Manager, click on File/Exit Windows
Windows exits to a MS-DOS command prompt
o Insert the BIOS installation diskette into your diskette drive (A:)
o Press Ctrl-Alt-Del (press and hold the <Ctrl> and <Alt> keys and press
the <Del> key) to restart the system
OTHER OPERATING SYSTEMS
o Close all open programs
o Shut down the operating system
o Insert the BIOS installation diskette into your diskette drive (A:)
o Restart the computer by pressing Ctrl-Alt-Del or turning the computer
OFF then on again
The computer will boot MS-DOS from the BIOS installation diskette, and
initiate the Flash BIOS installation routine. When the Flash BIOS
installation is complete, the success message is displayed:
Please push the RESET SW (or turn AC power OFF/ON) to restart!
ROM Write Successful!
Utility Finished!
Eject the diskette from drive A: and turn the computer OFF then ON, or press
the reset switch to restart your computer.
ADDITIONAL INFORMATION REGARDING THIS RELEASE
---------------------------------------------
If you are unable to use the Windows self-extractor, the self-extracting
ZIP archive can be extracted by executing it from a DOS prompt or it can be
extracted using PKUNZIP 2.04G or an equivalent UnZIP utility. A DOS batch
file, INSTINFO.BAT is provided in the ZIP archive which will create the BIOS
installation diskette. If all else fails, you can execute the
self-extracting diskette image manually. This file is named 1319D140.EXE, and
needs a parameter of A: (1319D140 A:) to successfully create the diskette in
drive A:
The self-extracting diskette image, 1319D140.EXE, will run under MS-DOS or a
command prompt under Windows 95/98, NT, or OS/2. PLEASE NOTE that long
directory names in the path where the self-extracting image file is stored
under Windows 9x or NT will cause the self-extracting image to abort. Long
directory names are supported under OS/2.
2) F12 INSTALLATION METHOD
---------------------------
Your Toshiba computer has a special keyboard function to install an
updated BIOS image.
To use this function, hold down the F12 while the computer is powered on.
The computer MUST be in BOOT mode, not Resume mode.
The F12 installation method will only work with the internal keyboard. If
your computer is docked with the display closed and you are using an external
keyboard, the computer will need to be undocked and the internal keyboard's
F12 key used.
When the computer starts up with the F12 key depressed, the following
message appears:
'Ready for BIOS update. Place the BIOS diskette in the drive, and press
any key when ready to proceed.'
Insert the diskette that contains CHGBIOSA.EXE and BIOFC04T.COM,
and press any key. The CHGBIOSA program will automatically load the
BIOFC04T.COM file.
3) RUN CHGBIOSA.EXE AT THE COMMAND PROMPT
-----------------------------------------
The CHGBIOSA program is designed to be run from the MS-DOS command
prompt. It cannot be run in a DOS box inside of Windows 3.x, Windows 9x,
OS/2 or other operating systems. It also will not run if a Memory Manager,
like EMM386, is loaded. The CHGBIOSA program can be run from a
floppy disk, hard drive, or PCMCIA drive. However, you will need a floppy
diskette (high or low density) in your A: drive at the time the CHGBIOSA
program is run.
When the CHGBIOSA program is executed by itself, it will prompt you
to specify where the BIOS image file, BIOFC04T.COM is located. Enter
the complete path and file name. Example: C:\3344TV14\BIOFC04T.COM.
NOTE!
-----
If your path for BIOFC04T.COM is anywhere other than the root directory
of the A: drive (A:\BIOFC04T.COM), CHGBIOSA will copy the BIOS image
file from its current location to the root directory of A: drive.
Optionally, the CHGBIOSA program can also be run from a single command
which includes the path to the BIOFC04T.COM file.
Example: CHGBIOSA C:\3344TV14\BIOFC04T.COM
CHANGE HISTORY
--------------
Version 1.40 06-26-2000
o A Hibernation problem was corrected. When the computer, running
Windows 95, went into Hibernation with a low charge remaining on the
battery, the computer would not come out of Hibernation properly.
Version 1.30 05-05-2000
o Corrected a problem that could cause the computer to hang when
accessing the printer port, prior to the computer being hot docked to
any docking device.
o Corrected an intermittent problem that would cause the computer to
hang at the Windows 2000 log on screen.
o Corrected a problem that, when running Windows 98, pressing a key
during the resume function would cause a keyboard or mouse not to be
accessible when the computer resumed.
o Corrected a problem that, when running Windows 98, in Packet Filtering
and Link Status Change, using Wake on LAN from the S3 or S4 state was
impossible
o Corrected a problem that, when connecting or disconnecting an AC
Adaptor while playing a sound in Windows 95, it was possible to set
"Throttling" via HCI (Human Computer Interaction), while a sound was
being played.
Version 1.20 05-05-2000
o Corrected an intermittent problem that caused the computer to hang
just after the BIOS was updated.
o Corrected a battery recognition problem. When running Windows 2000
OS, and computer being turned on, the battery was not recognized
properly when installed. CPU usage would not change from 100% usage
for a period of time.
o Corrected a problem that, under ACPI OS (Windows 98), accessing the
BIOS via the P-Code, such as the HCI function, was impossible.
o Corrected a problem that, when running Windows 2000, if USB Wake-Up
was set to "Enable", clicking a USB mouse button when the computer was
in Standby could cause the computer to shut down completely.
Version 1.10 04-14-2000
o Initial Production BIOS for Portege 3440CT
**end**
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.