PCMCIA 10Mbps Ethernet Card
Driver Diskette (Ver 2.60) Overview
TOPIC
======================================
1. DISKETTE CONTENTS
2. CLIENT DRIVER
3. SOCKET and CARD SERVICES INSTALLATION ADVISORY
4. DIAGNOSTIC PROGRAM
5. NETWARE DOS ODI DRIVER
6. PACKET DRIVER
7 NDIS DRIVER FOR OS2 LAN SERVER
8. NDIS DRIVER FOR WINDOWS FOR WORKGROUPS 3.11
9. NDIS DRIVER FOR LAN MANAGER V2.1
10. NDIS 3.1 DRIVER FOR WINDOWS 95
11. NDIS 3.1 DRIVER FOR WINDOWS 98
12. NDIS 3.1 DRIVER FOR WINDOWS NT 3.51
13. NDIS 3.1 DRIVER FOR WINDOWS NT 4.0
[1] DISKETTE CONTENTS
Files and
Subdirectories Contents
--------------------------------------------------------------------
\ETHERNET Tag File
\PCMCARD.INF Windows 95 Installation File
\DIAG.EXE PCMCIA Card Diagnostic Program
\INSTALL.EXE PCMCIA Installation Program
\CARDGO.EXE PCMCIA Client Driver
\README.TXT This file
\NETWARE.ODI Directory of Novell Netware DOS ODI Driver
\PKTDRV Directory of FTP Compliant Packet Driver Directory
\OS2 Directory of NDIS V2.0 Driver for OS2 LAN Server
\NDIS Directory of NDIS V2.0 Driver
\WFW311 Directory of NDIS V2.0 Enhance Mode Driver for WFW311
\MSLANMAN.DOS Directory of NDIS V2.0 Driver for Lan Manager V2.1
\LANTASTI.V60 Directory of NDIS V2.0 Driver for Lantastic V6.0
\WIN9X Directory of NDIS V3.1 Driver for Windows 95 and 98
\WINNT Directory of NDIS V3.1 Driver for Windows NT 3.51 and 4.0
[2] CLIENT DRIVER (For DOS and Windows 3.1 Only)
The CLIENT DRIVER is a PCMCIA controller enable program. This enable
program only need for DOS and Windows 3.1 system. You should installed
the Socket and Card service in your Notebook before executing the
client driver.If you do not have the Socket or card service program,
please call the Notebook vendor.The client driver will keep resident for
handle card inseration and removal events. This feature can prevent
system crash when remove the card from socket.
To load the client driver, type
CARDGO [/INT=x][/PORT=xxx][/MEM=xxxx][/U][/?]
in DOS command line, or
DEVICE=[PATHNAME]CARDGO.EXE [/INT=x][/PORT=xxx][/MEM=xxxx][/U][/?]
in config.sys file.
where:
[/INT=x] This specifies the hardware interrupt (IRQ) where your
card will be indicated.
The valid IRQs are 2,3,4,5,6,10,11,12,15.
[/PORT=xxx] This specifies the I/O address. The valid ports are 240,
280,300,320,340,360.
[/MEM=xxxx] This specifies the memory window address. The valid
MEMs are D000, D400, D800, DC00.
[/U] This specifies the client driver will free the resident
program when the card is remove from socket.
[/?] This specifies to indicate the program to display all
the possible syntax only.
The default syntax is:
CARDGO /INT=5 /PORT=300 /MEM=D400
After you executed the CARDGO.EXE, you will see the following display for
make sure install successful. Especially you must see the Node ID value.
Socket : 0 (for example)
IRQ Number : 05 (for example)
I/O PORT Base : 0300H (for example)
Memory Address: D400H (for example)
Node ID : 00 A0 0C 80 00 02 (for example)
Here is the list of error messages the driver may display and correction
method we suggested:
[Error 1]
"10Mbps Ethernet Card Enabler Fail in Request IRQ."
The IRQ number which you specified is not supported by the Card
Service or in conflict with other device.
(Correction:) To change the IRQ number to other valid value
list above.
[Error 2]
"10Mbps Ethernet Card Enabler Fail in Request IO Port."
The IO port which you specified is not supported by the Card Service or
in conflict with other device.
(Correction:) To change the IO port to other valid value list above.
[Error 3]
"10Mbps Ethernet Card Enabler Fail in Request Memory Window."
The memory window address which you specified is not supported by
the Card Service or in conflict with other device.
(Correction:) To change the memory window address to other valid
value list above.
[Error 4]
"10Mbps Ethernet Card Enabler Fail in General Error."
Register service fail with Card Service program.
(Correction:) To reboot system and try again.
[Error 5]
"Card Service is not compliant with Version 2.10,2.01 or 2.00 !"
(Correction:) To re-install a new Card Service.
[Error 6]
"10Mbps Ethernet Card is not Active ! Enable again."
May be the Ethernet controller malfunction.
(Correction:) To contack with your dealer.
[Error 7]
"May be the Card Service version is too old."
"Please re-install new version of Card Service."
(Correction:) To re-install a new Socket and Card Services.
[Error 8]
"Parameter Too Long."
The Parameters of CARDGO is too long.
(Correction:) To reference the default syntx list above and
correct it.
[Error 9]
"Unknown Parameters."
Syntax error of CARDGO.EXE.
(Correction:) To reference the default syntx list above and
correct it.
[Error 10]
"Invalid Value !"
An invalid parameter value.
(Correction:) To reference the valid values list above and
correct it.
[Warning 1]
"10Mbps Ethernet Card Enabler had already been resident."
The CARDGO.EXE is executed.
(Correction:) To reboot your system.
[3] SOCKET and CARD SERVICES INSTALLATION ADVISORY
For those who installed EMM386.EXE in your config.sys, please exclude
memory address D400-D7FF from your system. 10Mbps Ethernet Card
Enabler program will use this space to read Ethernet ID and CIS from
on-board serial EEPROM.
[Example]
DEVICE=EMM386.EXE NOEMS X=D400-D7FF
or
DEVICE=EMM386.EXE NOEMS X=D000-DFFF
For those who installed Card and Socket Services device driver in your
config.sys, please run CARDGO.EXE(see Client Driver) after those device
drivers. The default configuration is INT=5, PORT=300 and MEM=D400.
[Phoenix PCM+ V3.0]
DEVICE=C:\PCM3\CNFIGNAM.EXE /SETUP-DEFAULTS
DEVICE=C:\PCM3\PCMSS.EXE
DEVICE=C:\PCM3\PCMCS.EXE
DEVICE=C:\PCM3\PCMRMAN.SYS
DEVICE=C:\PCM3\PCMSCD.EXE
DEVICE=CARDGO.EXE
[SystemSoft CardSoft V3.1]
DEVICE=C:\CARDSOFT\SS365SL.EXE //Socket Service for Intel Compatible //
DEVICE=C:\CARDSOFT\CS.EXE
DEVICE=C:\CARDSOFT\CSALLOC.EXE
DEVICE=CARDGO.EXE
[Award CArdware V2.0]
DEVICE=C:\CARDWARE\SSPCIC.EXE
DEVICE=C:\CARDWARE\PCCS.EXE
DEVICE=C:\CARDWARE\PCRM.EXE /AUTODETECT
DEVICE=CARDGO.EXE
[Note] Please do not use PCENABLE.EXE
[AMI AMICARDZ]
DEVICE=C:\AMI\SSSL.SYS
DEVICE=C:\AMI\AMICS.SYS
DEVICE=CARDGO.EXE
[Note] Please do not use PCBE.SYS
[Databook CardTalk V3.02]
DEVICE=C:\CARDTALK\TMB250.SYS /io:240
DEVICE=C:\CARDTALK\CTALKCS.EXE
DEVICE=C:\CARDTALK\CARDTALK.EXE /A /IOW=300-31F /MEMW=D000-D7FF
DEVICE=CARDGO.EXE
[IBM Thinkpad Socket and Card Services V2.12]
DEVICE=C\EMM386.EXE NOEMS I=B000-B7FF X=C800-CFFF X=D000-DFFF
DEVICE=C:\THINKPAD\IBMDSS01.SYS /D
DEVICE=C:\THINKPAD\IBMDOSCS.SYS
DEVICE=C:\THINKPAD\DICRMU01.SYS /MA=C800-DFFF
DEVICE=C:\THINKPAD\$ICPMDOS.SYS
[4] DIAGNOSTIC PROGRAM
DIAG.EXE is a complete test program that users can make
sure if the card is good or not. It provides the following
card test functions:
. IRQ verify
. IO base verify
. RAM test
. Card Node ID test
. Internal Loopback test
. External Loopback test
[Note] Before execute diagnostic program, you must make sure the client
driver, CARDGO.EXE, is installed.
[5] Netware DOS ODI Driver
This directory contains Ethernet DOS ODI driver PCMODI.COM that
supports NetWare 3.x and 4.x, NetWare Lite and other ODI interface
application.
PCMODI.COM : DOS/ODI Driver for NetWare 3.x and 4.0.
The following instructions let you to install Novel NetWare Ver. 386
DOS ODI Driver :
5.1 How To Install
---------------
You need following five files to install DOS ODI DRIVER.
a. LSL.COM ---- supported by Novell
b. PCMODI.COM ---- Novell DOS ODI Driver ,supported
by manufacturer
c. IPXODI.COM ---- supported by Novell
d. NETx.COM ---- supported by Novell
or
EMSNETx.EXE
or
XMSNETx.EXE
e. NET.CFG ---- optional,configuration file
After boot your workstation, type following comments on the console:
LSL <Enter>
PCMODI <Enter>
IPXODI <Enter>
NETx <Enter>
then,you can log in to the file server.
Normally, you will need a NET.CFG file to configure your your card.
You can see Netware 386 Installation appendix E for more
information about NET.CFG.
Below is a sample NET.CFG file:
LINK DRIVER PCMODI
port 300
int 5
Frame Ethernet_II
Frame Ethernet_802.3
Protocol IPX E0 Ethernet_802.2
:
:
[6] Packet Driver
The driver PCMPKT.COM is the Packet driver.
To load the packet driver , type PCMPKT 0X60.
PCMPKT syntax:
PCMPKT [-h] [-n] [-d] [-w] [-u] <PACKET_INT_NO> [IRQ] [IO_BASE]
where:
[-h] Show on-line help.
[-n] Convert ETHERNET II header to IEEE 802.3 header.
[-d] Do not start LAN card until this driver is
called by the higher layer programs first.
[-w] Running under Windows environment.
[-u] Unload packet driver.
<PACKET_INT_NO> This specifies the software interrupt (IRQ) where
you'll load the packet driver. It must be in the range
0x60 to 0x80.
[IRQ] This specifies the hardware interrupt (IRQ) where your
card will be indicated.
[IO_BASE] This specifies the I/O address .
Example:
The following command line loads the Ethernet Packet Driver
at software interrupt 60h, at I/O address 300, at hardware interrupt 5.
PCMPKT 0x60 0x5 0x300
or
PCMPKT 0x60
Note: The default I/O address is 300 .
Note: The default hardware interrupt is 5
Note: The placement of 0x prior to the parameters.
[7] NDIS V2.0 DRIVER FOR OS2 LAN SERVER
The Ethernet NDIS2 Driver for IBM OS2 LAN SERVER confirms to the Network
Driver Interface Specification(NDIS2). This document shows you how to setup
the driver and how to use the enhanced functions by setting the custom
keywords in configuration file.
Installation by using IBM OS2 LAN SERVER Installation utility:
---------------------------------------------------------
Please install the IBM LAN SERVER OS2 driver files following the procedures
as described in the following.
1. Install OS/2 Lan Server to HardDisk and install Ethernet
adapter in your system properly.
2. In OS/2 window, Click the "MPTS" icon.
3. The screen will display the IBM Logo panel, press "OK".
4. Select "Install" button.
5. Insert the Driver Diskette, specify the driver path
A:\OS2 and press <Enter>.
6. When complete above step, then configure your system.
7. The same step as step 4, select "Configure" button.
8. The screen will display "Configure" dialog box and select "LAN
adapters and protocols" then press "configure" button.
9. The screen will display "LAPS Configuration" dialog box, move
highlight to "PCMCIA 10Mbps Ethernet Card"
item in "Network Adapter" window, and select "NetBios" "IEEE802.2"
protocol. Press "OK".
10. Installation is complete now. Reset your PC by turning it off
and on.
Configuration Files:
====================
Sample of configuration file:
-----------------------------
File Name: C:\CONFIG.SYS
----------
...
Device=C:\IBMCOM\MACS\CARDGO.OS2 /IRQ 5 /IO 300
Device=C:\IBMCOM\MACS\PCMNDIS.OS2
...
CARDGO.OS2 command-line options
-------------------------------
/IRQ x x specifies the IRQ
/IO yyy yyy specifies the IO Base address
File Name: C:\IBMCOM\PROTOCOL.INI
----------
...
[IBMLXCFG]
LANDD_nif = LANDD.nif
NETBEUI_nif = NETBEUI.nif
ODI2NDI_nif = ODI2NDI.nif
TCPIP_nif = TCPIP.nif
PCMCIA_nif = PCMCIA.nif
...
[LANDD_nif]
DriverName = LANDD$
Bindings = PCMCIA_nif
ETHERAND_TYPE = "I"
...
[NETBEUI_nif]
DriverName = netbeui$
Bindings = PCMCIA_nif
ETHERAND_TYPE = "I"
...
[ODI2NDI_nif]
DriverName = odi2ndi$
Bindings = PCMCIA_nif
...
[TCPIP_nif]
DriverName = TCPIP$
Bindings = PCMCIA_nif
[PCMCIA_nif]
DriverName = PCMNDIS$
IRQ = 3
IOBASE = 0x300
Custom Keywords:
----------------
IRQ This keyword is used to set the
interrupt of the adapter
IOBASE This keyword is used to set the
I/O base address of the adapter
Important :
=============
When using "IBM Netware Requester Support" protocol to connect to Novell
server, be sure to fill the parameter(Network Adapter Address) to be the
same address as the Ethernet Address of ETHERNET NIC.
[8] NDIS DRIVER FOR WINDOWS FOR WORKGROUPS 3.11 INSTALLATION
A) Install NDIS driver to the WFW 3.11
The drivers named PCMNDIS.386 contained in the directory
conform to the Network Driver Interface
Specification (NDIS) defined by Microsoft/3Com.
NDIS Enhance Mode Driver Installation on Windows for Workgroups
--------------------------------------------------
1. Run Windows by typing WIN from the DOS prompt.
2. Click the "Network" icon in the Main Program
Group.
3. Click the "Network Setup" icon from the Network window.
4. Select "Drivers" item from the Network Setup dialog box.
5. Select "Add Adapters" item in the Option dialog box.
6. Select "Unlisted or Updated Network Adapter" when the
Install driver field appears.
7. Type destination drive and path name in your PC.
Make sure the full path of the directory (i.e. A:\WFW311)
is given.
8. Insert 10Mbps Ethernet Card Driver Diskette in your floppy drive
and press <Enter> to start the installation process.
9. When the "PCMCIA 10Mbps Ethernet Card" dialog box appear,
press<Ok> to select the adapter.
10.Follow screen instructions to complete the process.
11.Restart your computer.
Sample Configuration Files
======================================================
1. PROTOCOL.INI File on Windows for Workgroups 3.11
[network.setup]
version=0x3110
netcard=ETHERNET,1,ETHERNET,1
transport=ms$nwlinknb,NWLINK
transport=ms$ndishlp,MS$NDISHLP
transport=ms$netbeui,NETBEUI
lana0=ETHERNET,1,ms$nwlinknb
lana1=ETHERNET,1,ms$ndishlp
lana2=ETHERNET,1,ms$netbeui
[protman]
DriverName=PROTMAN$
PRIORITY=MS$NDISHLP
[NWLINK]
BINDINGS=ETHERNET
FRAME=ETHERNET_802.2
[MS$NDISHLP]
DriverName=ndishlp$
BINDINGS=ETHERNET
[NETBEUI]
DriverName=netbeui$
SESSIONS=10
NCBS=12
BINDINGS=ETHERNET
LANABASE=1
[ETHERNET]
DriverName=PCMNDIS$
IRQ=5
IOBASE=0x300
2. To change the IRQ and IOBase setting, edit the PROTOCOL.INI file,
and change the IRQ and IOBASE values in [ETHERNET] section.
[9] NDIS Driver for LAN Manager Installation
Installation Introduction for LAN Manager V2.1
--------------------------------------------------
a. Type "lmsetup" In LanManager Directory. Press Enter.
b. Choice "Network Drivers..." in " Configuration ". Press Enter.
c. Choice <Add New Configs> ,press Enter.
Network Adapter Driver appears.
d. Choice <Other Driver> , press Enter.
e. Insert the Driver Disk to specified drive (A:\> or B:\>),key in the
specified drive (A:\> or B:\>),then push <OK> button.
f. Select a available Network Adapter Driver,
"PCMCIA 10Mbps Ethernet Card"
Push <OK> button.
g. Press the SPACEBAR to select the protocol what you want.
h. Push <OK> button.
Configuration Complete appear.
i. Push <Save> button.
j. Press "F3" to exit.
k. Press Enter.
l. Copy "CARDGO.EXE" in Driver Diskette to LanManager Directory.
Sample configuration files:
[CONFIG.SYS]
a.<V2.1>
DEVICE=C:\LANMAN.DOS\CARDGO.EXE
DEVICE=C:\LANMAN.DOS\DRIVERS\PROTMAN\PROTMAN.DOS /i:C:\LANMAN.DOS
DEVICE=C:\LANMAN.DOS\DRIVERS\PCMNDIS.DOS
[Protocol.ini file for LAN Manager]
a. V2.1
[PROTMAN]
DRIVERNAME = PROTMAN$
DYNAMIC = YES
PRIORITY = NETBEUI
[NETBEUI_XIF]
Drivername = netbeui$
SESSIONS = 6
NCBS = 12
BINDINGS = "PCMCIA_NIF"
LANABASE = 0
[PCMCIA_NIF]
; protocol.ini section for PCMCIA 10Mbps Ethernet Card
IOBASE = 0x300
IRQ = 5
DRIVERNAME = PCMNDIS$
[Autoexec.bat file for LAN Manager]
a. V2.1
@REM ====== LANMAN 2.1 === DO NOT MODIFY BETWEEN THESE LINES
SET PATH=C:\LANMAN.DOS\NETPROG;%PATH%
NET START WORKSTATION
LOAD NETBEUI
@REM ====== LANMAN 2.1 === DO NOT MODIFY BETWEEN THESE LINES
[10] NDIS 3.1 Driver for Windows 95 Installation
INSTALLATION PROCEDURE:
1) Insert 10Mbps Ethernet Card into the PCMCIA slot.
The system displays the "New Hardware Found" window,
with "PCMCIA-Ethernet Card" as the device name.
2) Select "Drivers from disk provided by hardware manufacturer"
if it is retail version Windows 95 (4.00.950).
3) Insert the driver diskette, then press enter.
4) Occasionally, the system may ask for files from the Windows 95
CD-ROM. Follow the prompt until the installation is complete.
5) Reboot the machine to start the network.
[11] NDIS DRIVER FOR WINDOWS 98
INSTALLATION PROCEDURE:
1) Insert 10Mbps Ethernet Card into the PCMCIA slot.
The system displays the "New Hardware Found" window,
with "PCMCIA-Ethernet Card" as the device name.
2) Click Next, then select "Search for the best driver for your device.",
and click Next to continue.
3) Uncheck the "Microsoft Windows Update". Let Windows 98 search floppy
disk drives only. Then insert the driver diskette and click Next.
4) Select the found updated driver, PCMCIA 10Mbps Ethernet Card,
then click Next.
5) Occasionally, the system may ask for files from the Windows 98
CD-ROM. Follow the prompt until the installation is complete.
5) Reboot the computer to start the network.
[12] NDIS DRIVER FOR WINDOWS NT 3.51
INSTALLATION PROCEDURE:
1) Open the Control Panel, and choose Network Settings.
2) Click the Add Adapter button.
3) Select <Other> Requires disk from manufacturer.
4) Type in the path A:\WINNT
5) Select the "PCMCIA 10Mbps Ethernet Card".
6) Set the IRQ level and I/O Port Address to any free resources,
Valid IRQ's=2,3,4,5,6,10,11,12,15.
Valid I/O's=240,280,300,320,340,360.
7) Select Bus Type as "PCMCIA".
8) Leave the Bus Number Selected at 0.
9) Click on OK and back to the Network Settings.
10) Click on "Bindings" button.
11) Click on OK and Restart the Machine.
[13] NDIS DRIVER FOR WINDOWS NT 4.0
INSTALLATION PROCEDURE:
1) Open the Control Panel, and choose Network
2) Select Adapter tab and click the Add button.
3) Click Have Disk button.
4) Type in the path A:\WINNT
5) Select the "PCMCIA 10Mbps Ethernet Card".
6) Set the IRQ level and I/O Port Address to any free resources,
Valid IRQ's=2,3,4,5,6,10,11,12,15.
Valid I/O's=240,280,300,320,340,360.
7) Select Bus Type as "PCMCIA".
8) Leave the Bus Number Selected at 0.
9) Click on OK and back to the Network Settings.
10) Click on "Bindings" button.
11) Click on OK and Restart the Machine.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.