4560SLXdd.txt Driver File Contents (74p4795.zip)

 
4560-SLX Windows 2000 Device Driver Version 1.0.3

Table of Contents:
Introduction
Change history
Making the library installation diskette
Installing the library driver
Summary

INTRODUCTION:

This document contains instructions for installing the IBM 4560-SLX Library
driver for Windows 2000 and Windows XP (32-bit) Intel platforms.
This driver is for 32-bit Intel Platforms only.




Change history:

 Version 1.0.3   - Added support for IBM 4560SLX, 10/14/02
 Version 1.0.2   - libxprmc.sys, libxprmc.inf 09/10/01
                 - Added support for older code versions of the changers
                 - Completed adding support for Neo/MSL
 Version 1.0.0.5 - libxprmc.sys 02/23/01, libxprmc.inf 02/23/01, NextGen support
                 - No changes to sys file from 04/20/00 version
                 - Adds:  Ovrl Neo Series/Cmpq MSL Series
 Version 1.0.0.4 - libxprmc.sys 04/20/00, libxprmc.inf 04/20/00, AIT-2 support
 Version 1.0.0.3 - libxprmc.sys 04/06/00, libxprmc.inf 04/06/00, B2195
 Version 1.0.0.2 - libxprmc.sys 10/14/99, libxprmc.inf 02/17/00, RC2, WHQL Signed
 Version 1.0.0.1 - libxprmc.sys 01/18/00, libxprmc.inf 01/18/00, B2195?, Compaq only
 Version 1.0.0.0 - libxprmc.sys 10/14/99, libxprmc.inf 01/19/00, RC2


MAKING THE LIBRARY DISKETTE:


To make the Installation Diskette, copy the following 2 files from
your User Guide CD (in the Device Driver folder) to a formatted 3 1/2 inch floppy disk.

     libxprmc.inf
     libxprmc.sys


INSTALLING THE LIBRAY DRIVER: 

     1.  Shutdown Windows if it is running and power down the system.

     2.  Connect the IBM 4560-SLX Library to the system.  Ensure that the
         SCSI bus is terminated correctly and that there are no target
         ID conflicts.  Power on the autoloader.

     3.  Startup the system and log into Windows.

     4.  Right-click on the "My Computer" Icon and select "Manage".
         This will bring up the Computer Management applet.

     5.  In Computer Management, double-click "Device Manager".
         A list of device subsystems will be displayed in the right view.

     6.  The target autoloader may be found in the "Medium Changers"
         section.  Expand the section where the
         target autoloader is located.  Right-click the target "Uknown Medium Changer" 
         and select "Properties".

         NOTE: Troubleshooting the SCSI bus that the target autoloader
         is attached to will be necessary if Windows 2000 does not
         see the autoloader in the "Medium Changers" section.
         Do not continue installation until this is resolved.

     7.  In the Properties window, verify that the SCSI ID matches
         that of the library that you are installing.

     8.  Select the "Driver" tab and then select "Update Driver...".
         This will start the "Upgrade Device Driver" Wizard.

     9.  In the Device Wizard, select "Next".

     10. Select "Display a list of the known drivers for this device so
         that I can choose a specific driver" radio button.

     11. Select "Next". 

     12. Click "Have Disk"

     13.  Insert the floppy disk into the floppy drive.  Make sure
         that the path name to the drive is correct.

     14. Highlight the listed IBM 1x16 Autoloader driver and then click
         "Next".

     15. The "Start Device Driver Installation" view is displayed.

     16. Click "Next" to install the driver.

          a. Should the Wizard indicate that the driver already exists on
            the system and prompts you for a selection, select "New". 

          b. The Windows 2000 Setup window is displayed.  Verify the
            correct path to the driver, then select "Continue".

     17. The next view is "Completing the Upgrade Driver Wizard".  Click
         "Finish".  You may be prompted to reboot your system.

     18. The IBM 4560-SLX Library driver is installed.


SUMMARY

If you have problems, questions or feedback relating to the installation or 
usage of this driver please contact IBM technical support at:

   http://www.pc.ibm.com/support

Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web1, load: 0.84