SMC Networks, Inc. SMC 10/100 PC Card (SMC8041 V.2) NetWare Server Driver Installation Contents: 1. Files Description 2. Enable the SMC 10/100 PC Card (SMC8041 V.2) 3. Driver Installation for NetWare Server 3.1x 4. Driver Installation for NetWare Server 4.x 5. Driver Installation for NetWare Server 5.x 6. Optional Parameters for SMC80412.LAN 1. Files Description ------------------------------------------------------------- Filename Description ------------------------------------------------------------- README.TXT This file. Presents a summary for NetWare Server driver installation. SMC80412.LAN SMC 10/100 PC Card (SMC8041 V.2) 32-Bit ODI Server driver. SMC80412.LDI Driver installation information file. ETHERTSM.NLM NetWare Server 3.1X, 4.X LAN driver Topology Specific Module (TSM) for Ethernet. 3.1X\NBI31X.NLM NetWare Server 3.1X Bus Interface module. 3.1X\MSM31X.NLM NetWare Server 3.1X LAN driver Media Support Module (MSM). 4.X\MSM.NLM NetWare Server 4.X LAN driver Media Support Module (MSM). ------------------------------------------------------------------ 2. Enable the SMC 10/100 PC Card (SMC8041 V.2) SMCOPEN.EXE is the SMC 10/100 PC Card (SMC8041 V.2) enabling program. You have to run SMCOPEN.EXE under DOS to enable SMC 10/100 PC Card (SMC8041 V.2) before bringing up the Netware Server. The SMC 10/100 PC Card (SMC8041 V.2) server driver will not work if the adapter is not enabled first in DOS. The syntax for SMCOPEN is: SMCOPEN [/IRQ=x] [/MEM=mm] [/IO=nnn] [/O] [/?] Valid options: x = Interrupt number (3, 4, 5, 9, 10, 12, 15). This number must not be in use by any other device in the system. mm = Hex memory location (e.g. C0, C8, D0, D8). nnn = IO range (300, 320, 340, 360). SMC 10/100 PC Card (SMC8041 V.2) requires 32 consecutive free I/O port addresses. /O (overwrites current socket settings). /? Displays this screen. The default value for IRQ is 3. The default value for IOP is 0x300. Example: The following command enables SMC 10/100 PC Card (SMC8041 V.2) with IRQ 5 and I/O port address 300: SMCOPEN /IRQ=5 /IO=300 3. Driver Installation for NetWare Server 3.1x 1. Insert SMC 10/100 PC Card (SMC8041 V.2) Driver Disk in the floppy drive (e.g. A:). 2. Copy the following file from the Driver Disk to the root directory on the hard disk: \ENABLER\SMCOPEN.EXE Exeute SMCOPEN to enable the SMC 10/100 PC Card (SMC8041 V.2) as described in Section 2 above. 3. Change to the NetWare Server directory (for example: CD \SERVER.312) 4. Copy the following files from Driver Disk to the NetWare Server directory on the hard disk: \NETWARE\SERVER\3.1X\NBI31X.NLM \NETWARE\SERVER\3.1X\MSM31X.NLM \NETWARE\SERVER\ETHERTSM.NLM \NETWARE\SERVER\SMC80412.LAN -------------------------------------------------------------------------- Sample AUTOEXEC.NCF for NetWare Server 3.12 LOAD C:NBI31X LOAD C:MSM31X LOAD C:ETHERTSM LOAD C:SMC80412 FRAME=ETHERNET_802.2 NAME=E_8022 LOAD C:SMC80412 FRAME=ETHERNET_802.3 NAME=E_8023 LOAD C:SMC80412 FRAME=ETHERNET_II NAME=E_II LOAD C:SMC80412 FRAME=ETHERNET_SNAP NAME=E_SNAP BIND IPX E_8022 NET=10 BIND IPX E_8023 NET=20 BIND IPX E_II NET=30 BIND IPX E_SNAP NET=40 -------------------------------------------------------------------------- 4. Driver Installation for NetWare Server 4.X 1. Copy the following files from the Driver Disk to the NetWare Server directory on the hard disk. \NETWARE\SERVER\4.X\MSM.NLM \NETWARE\SERVER\ETHERTSM.NLM \NETWARE\SERVER\SMC80412.LAN Copy the following file from the Driver Disk to the root directory on the hard disk: \ENABLER\SMCOPEN.EXE Exeute SMCOPEN to enable the SMC 10/100 PC Card (SMC8041 V.2) as described in Section 2 above. 2. Change to NetWare Server directory (for example: CD \NWSERVER). 3. Load the NetWare Server System by typing SERVER, and press <Enter>. 4. When the Server prompt appears, load the NetWare Server Installation Utility by entering the following command on the server console: LOAD INSTALL 5. Select "Driver options" from the "Installtion Options" menu, and press <Enter>. 6. Select "Configure network drivers" from the "Driver Options" menu, and press <Enter>. 7. Select "Select a driver" from the "Additional Driver Actions" menu, and press <Enter>. 8. Press <Ins> to install an unlisted driver, and press <F3> to specify a different path. 9. Insert the SMC 10/100 PC Card (SMC8041 V.2) Driver Disk in the floppy drive (e.g. A:), and specify the directory on the Driver Disk where the drivers are located (e.g. A:\NETWARE\SERVER). 10. Select "SMC8041 V.2 10/100 PC CARD" from the "Select a driver to install:" menu, and press <Enter>. 11. If necessary, select "Select/Modify driver parameters and protocols" from the "Board SMC 10/100 PC Card (SMC8041 V.2) (Driver SMC80412) Actions" menu, and press <Enter> to set up the driver parameters. After the driver parameters are set, select "Save parameters and load driver", and press <Enter>. 12. Follow instructions to complete driver installation. 13. Bring down the server by entering "down", and then "exit." This brings the system back to the MS-DOS prompt. 14. Bring up the server by entering "server" on the MS-DOS command prompt. After the server comes up, the SMC 10/100 PC Card (SMC8041 V.2) and the network should be working. 15. Please beware that each time you reboot the system, you have to run SMCOPEN.EXE to enable SMC 10/100 PC Card (SMC8041 V.2) as described in section 2 above. -------------------------------------------------------------------------- Sample AUTOEXEC.NCF for NetWare Server 4.X LOAD C:NBI LOAD C:MSM LOAD C:ETHERTSM LOAD C:SMC80412 FRAME=ETHERNET_802.2 NAME=E_8022 LOAD C:SMC80412 FRAME=ETHERNET_802.3 NAME=E_8023 LOAD C:SMC80412 FRAME=ETHERNET_II NAME=E_II LOAD C:SMC80412 FRAME=ETHERNET_SNAP NAME=E_SNAP BIND IPX E_8022 NET=10 BIND IPX E_8023 NET=20 BIND IPX E_II NET=30 BIND IPX E_SNAP NET=40 -------------------------------------------------------------------------- 5. Driver Installation for NetWare Server 5.x 1. Copy the following files from the Driver Disk to the NetWare Server directory on the hard disk. \NETWARE\SERVER\4.X\MSM.NLM \NETWARE\SERVER\ETHERTSM.NLM \NETWARE\SERVER\SMC80412.LAN Copy the following file from the Driver Disk to the root directory on the hard disk: \ENABLER\SMCOPEN.EXE Exeute SMCOPEN to enable the SMC 10/100 PC Card (SMC8041 V.2) as described in Section 2 above. 2. Change to NetWare Server directory (for example: CD \NWSERVER). 3. Load the NetWare Server System by typing SERVER, and press <Enter>. 4. When the Server prompt appears, load the NetWare Server Installation Utility by entering the following command on the server console: LOAD NWCONFIG 5. Select "Driver options" from the "Installtion Options" menu, and press <Enter>. 6. Select "Configure network drivers" from the "Driver Options" menu, and press <Enter>. 7. Select "Select a driver" from the "Additional Driver Actions" menu, and press <Enter>. 8. Press <Ins> to install an unlisted driver, and press <F3> to specify a different path. 9. Insert the SMC 10/100 PC Card (SMC8041 V.2) Driver Disk in the floppy drive (e.g. A:), and specify the directory on the Driver Disk where the drivers are located (e.g. A:\NETWARE\SERVER). 10. Select "SMC 10/100 PC Card (SMC8041 V.2)" from the "Select a driver to install:" menu, and press <Enter>. 11. If necessary, select "Select/Modify driver parameters and protocols" from the "Board SMC 10/100 PC Card (SMC8041 V.2) (Driver SMC80412) Actions" menu, and press <Enter> to set up the driver parameters. After the driver parameters are set, select "Save parameters and load driver", and press <Enter>. 12. Follow instructions to complete driver installation. 13. Bring down the server by entering "down", and then "exit." This brings the system back to the MS-DOS prompt. 14. Bring up the server by entering "server" on the MS-DOS command prompt. After the server comes up, the SMC 10/100 PC Card (SMC8041 V.2) and the network should be working. 15. Please beware that each time you reboot the system, you have to run SMCOPEN.EXE to enable SMC 10/100 PC Card (SMC8041 V.2) as described in section 2 above. 6. Optional Parameters for SMC80412.LAN The following are the optional parameters for SMC80412.LAN: 1. FRAME: Specifies which frame type is used by the driver. Accepted values are Ethernet_802.2, Ethernet_802.3, Ethernet_II and Ethernet_SNAP. Multiple frame types can be enabled by loading the same driver with different FRAME types. Examples: LOAD SMC80412 FRAME=ETHERNET_802.2 LOAD SMC80412 FRAME=ETHERNET_802.3 LOAD SMC80412 FRAME=ETHERNET_II LOAD SMC80412 FRAME=ETHERNET_SNAP 2. INT: The Interrupt (IRQ) value to be used by the adapter. You have to pay attention that the INT value you specified here must match the /IRQ value you specified for SMCOPEN, the SMC 10/100 PC Card (SMC8041 V.2) DOS enabling program. Please refer to section 2 on how to use SMCOPEN to enable SMC 10/100 PC Card (SMC8041 V.2) in DOS before bringing up the server. Example: LOAD SMC80412 INT=3 FRAME=ETHERNET_802.2 3. PORT: The starting I/O port address. You have to pay attention that the PORT value you specified here must match the /IOP value you specified for SMCOPEN, the SMC 10/100 PC Card (SMC8041 V.2) DOS enabling program. Please refer to section 2 on how to use SMCOPEN to enable SMC 10/100 PC Card (SMC8041 V.2) in DOS before bringing up the server. Example: LOAD SMC80412 INT=3 PORT=300 FRAME=ETHERNET_802.2 4. AUTOSENSE | SPEED 10/100 | DUPLEX FULL/Half These parameters are mutually exclusive and you can specify only one of them on the command line. SPEED: This keyword specifies the connection speed mode: 10 or 100. DUPLEX: This keyword specifies the connection duplex mode: FULL or HALF. If none of the parameters is specified, the connection type is set to Auto-negotiation. Example: ; set connection type to 10 Mbps and Full Duplex LOAD SMC80412 SPEED 100 DUPLEX FULL FRAME=ETHERNET_802.2Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.