SMC Networks Inc. SMC EZ Card 10 Ethernet PCI Network Cards SCO UNIX STREAM DRIVER For Ethernet LAN Cards INSTALLATION GUIDE This software is licensed by SMC for use by its customers only. Copyright (c) 1998 SMC Networks Inc. All rights reserved. SUPPORTED NETWORK CARDS SMC's EZ Card 10 Ethernet PCI Network Cards: o SMC1208T o SMC1208BT o SMC1208BTA The unix driver contained in the directory \SCO is for the following PCI Ethernet adapter: SMC EZ Card 10 PCI (SMC1208) Contents: --------- A. Installing MDI Unix Driver for SCO ODT 5.0 B. Installing LLI Unix Driver for SCO 3.2.4 (ODT 3.0) File Description ================ 5.X\ SCO ODT 5.0 MDI Unix Driver 3.X\ SCO 3.2.4 (ODT 3.0) LLI Unix Driver SCOUNIX.TXT this file A. Installing MDI Unix Driver for SCO ODT 5.0 ============================================== 1. Log into the UNIX system as supervisor (root) and enter Maintenance mode. (Note: Make sure that the current directory is "/" using UNIX command - pwd.) Please follow the steps shown below to uncompress the package file: > cd /tmp (and insert the floppy in the proper drive, i.e. a:) > doscp a:/sco/5.x/vol.000 ./VOL.000.000 Now the installation directory is ready for use. 3. The following sections describe configuration of the driver. We suggest that you carry out these instructions in a singler-user environment. Run the custom utility and select the "Install new package" option. Select Media Type "Media Image" and type Image Directory "/tmp " It will prompt with "SMC EZ Card 10 PCI (SMC1208) (ver 2.0.0)" After running the custom utility and the new package is installed, you should use the "netconfig" command to add the driver into your system as described in step 4 below. 4. Run "netconfig". Add the desired chain. 5. When the chain has been configured, select 'q' from the netconfig menu. and relink the kernel at the prompt. 6. To activate the adapter, you must reboot. When the system boots, you should see the following data dispalyed among the configuration messages: %ethernet 0xD800-0xD81F 11 - type=100 addr=00-00-e8-xx-xx-xx . . The display of the last three bytes of the IEEE address depends on the adapter currently plugged into your system. 7. If you encounter any problems during installation, (i.e., an error message appears on screen) call your dealer for assistance. B. Installing LLI Unix Driver for SCO 3.2.4 (ODT 3.0) ====================================================== 1. Plug the SMC1208 PCI Ethernet Adapter into the PCI slot on your PC machine. 2. Turn ON the machine and log in as "root" user. (In maintenance mode) 3. Insert the SMC1208 SCO UNIX Driver diskette in floppy drive A: and enter the following command from the Unix Shell to install the SCO Unix driver. # cd /tmp # doscp a:/sco/3.x/setup . # chmod +x setup # ./setup 4. The screen will prompt you with the following message, Install SMC1208 PCI Ethernet Adapter LLI Driver Please input source path ? (ex.: a:/sco/3.x) 5. Enter the driver's full path (a:/sco/3.x) and press the ENTER key to start copying the driver files to the Unix system. 6. Run the "netconfig" command from Unix shell. # netconfig 7. Select "1. Add a chain" from the configuring chain options. 8. Select "4. sco_tcp SCO TCP/IP for UNIX" from the configuring protocol options. 9. Select "18. r3e0 SMC EZ Card 10 PCI LLI Driver, board 0" from the configuring driver options. 10. The system will prompt you with the following message to complete configuring the driver chain, ... Add chain sco_tcp->r3e0 (y/n): y ... Enter the internet address of this interface: 203.70.236.92 Enter the netmask for this interface (default: 255.255.255.0): (press Enter key) Does the interface use a broadcast address of all 1's? (y/n) (default: y): (press Enter key) Enter the broadcast address for this interface (default: 203.70.236.255): (press Enter key) ... Are these values correct? (y/n): y ... Enter local host name or enter q to quit [sco324]: (press Enter key) ... 32 Pseudo ttys ... ... Select an option or enter q to quit [q]: (press Enter key) ... 256 TCP connections ... ... Select an option or enter q to quit [q]: (press Enter key) ... 11. Select "q. Quit" from the configuring chain options. 12. The system will prompt you with the following message to relink the system's kernel file, ... Do you want to relink the kernel now? y ... Do you want this kernel to boot by default? (y/n) y ... Do you want the kernel environment rebuilt? (y/n) y ... 13. Reboot the Unix system to initialize the driver fuction. # reboot TRADEMARKS ========== All Tademarks or Brand names mentioned are properties of their respective companies. == End of File ==Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.