1. Enet32vl.zip Driver
2. NW311.TXT File Contents

NW311.TXT Driver File Contents (Enet32vl.zip)

	 ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»
	 º                                                   º
	 º     Compex ENET32-VL Ethernet Network Adapter     º
	 º   (C) Copyright PDS, 1995. All Rights Reserved.   º
	 º                                                   º
	 ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ


1) INSTALLATION GUIDE
=====================

Below are guidelines for installing the server driver, EN32VL.LAN,
in a NetWare v3.11 environment.

1.  In the NetWare v3.11 directory, run SERVER.EXE

2.  At the NetWare prompt, type:

	       : LOAD A:\NW.311\LSLENH <Enter>
	       : LOAD A:\NW.311\EN32VL <Enter>

    The first line loads LSLENH.NLM which will automatically loads PATCHMAN.NLM.
    The second line loads EN32VL.LAN which will automatically loads MSM3X.NLM
    and ETHERTSM.NLM.  Note that EN32VL.LAN loaded without specifying the cable
    type will perform an auto-detection of the cable type. The frame type is
    defaulted to Ethernet_802.3.

    Below is an example to use cable type TP and frame type Ethernet_802.2

	       : LOAD A:\NW.311\EN32VL TP FRAME=Ethernet_802.2

    Please note that if you need to use the MONITOR.NLM module in NetWare v3.11,
    do use the version that is included in the driver diskette. The original
    version may cause the server crash when <LAN/WAN Information> option is
    selected. To load MONITOR.NLM, type

	       : LOAD A:\NW.311\MONITOR

3.  Bind IPX to the server driver by typing:

	       : BIND IPX EN32VL NET=number <Enter>

    The NetWare v3.11 server is now properly setup.

4.  The server driver may also be installed without loading it manually
    from the driver diskette each time the NetWare server is started.
    Follow the steps below.

    a) When the server has been setup properly from the procedures described
       above, login to the server from a workstation. Please refer to the
       documentation in \DOSODI.

    b) At the workstation, copy the files from \NW.311 in the driver diskette
       to the server directory \SYSTEM.

    c) At the server console, edit the AUTOEXEC.NCF by typing:

		: LOAD INSTALL <Enter>

       Select "System Option" and "Edit AUTOEXEC.NCF file". Add these lines.

		LOAD LSLENH
		LOAD EN32VL
		BIND IPX EN32VL NET=number

       Note that you may add additional command line options to use
       different frame types.

       The server driver will now be loaded automatically when the NetWare
       server is started.


2) COMMAND LINE OPTIONS
=======================
 
Apart from the standard command line options of FRAME, etc,
the server driver provides additional command line options.

    1  BOARD

       This option selects the adapter on the system. The valid values
       are 1 - 99. It has to be used together with the FRAME keyword if
       multiple frames need to be loaded. To load multiple frames, the
       BOARD keyword has to be specified during the first and subsequent
       loading of the driver.

       For example, to load multiple frame types for one physical ENET32-VL
       adapter, the following should be entered:

	    LOAD EN32VL FRAME=Ethernet_802.2 BOARD=1 <enter>
	    LOAD EN32VL FRAME=Ethernet_802.3 BOARD=1 <enter>
	    LOAD EN32VL FRAME=Ethernet_II BOARD=1    <enter>
	    LOAD EN32VL FRAME=Ethernet_SNAP BOARD=1  <enter>

       The driver must then be bound to the IPX protocol for each frame
       type.

       Note: The BOARD keyword is not to be mistaken with the standard
	     PORT keyword which selects the physical adapter on the system
	     by specifying the I/O address.

    2. TP

       This option is used to set the cable type to Twisted Pair
       without performing any auto-detection of cable type.