*******************************************************************
* SMC Networks, Inc. *
* SMC EZ Connect 802.11a Access Point *
* (SMC2755W) *
* *
* Copyright (C) 2001 SMC Networks, Inc. *
* All Rights Reserved. *
* *
* V1.07 11-14-2002 *
*******************************************************************
===================================================================
Introduction
===================================================================
This release package contains the SMC2755W 802.11a Wireless Access
Point Firmware Update .dlf file.
===================================================================
WARNING NOTES
===================================================================
1) After the firmware upgrade process is completed, please log into
the AP, go to [System] in the Advanced Setup and perform a reset to
factory defaults. This will allow the new firmware to fully take
effect.
2) The login page is case-sensitive in the web UI. Must enter
capital "A" for the username "Admin". The default password is "5up".
===================================================================
Installation
===================================================================
The firmware files can be upgraded through the web-based interface.
Follow the steps below to upgrade the firmware:
1. Login to the Admin Webpage: http://192.168.1.20
2. Type in Username and Password
(Default login information is U:Admin P:5up)
3. Click on Advanced Setup
4. Click on System to access the upgrade firmware section
5. Click on the [Browse] button to located the .dlf file on
your hard drive
6. Once you have browsed to the correct file, click [Open]
7. Click [Start Upgrade] to begin the upgrade process.
8. When prompted, reboot the Access Point to complete the
upgrade process
====================================================================
REVISION HISTORY
====================================================================
--------------------------------------------------------------------
Firmware Number
- Changes
--------------------------------------------------------------------
V1.00
- Initial Release
V1.01
- Change the default configuration in manufacturing for the
DHCP Client settings. (enable DHCP client by default) If
a DHCP server is not available, the unit will default to
192.168.1.20
- Added Apply/Reboot button at the end of the setup wizard
- Fixed configuration parameters
- Ask for confirmation and reboot the system
- Added Encryption Key descriptions in the setup wizard
- Added System Name under Identification and modified
description
- Labeled the Data Rate information, in the Performance
Window and Synchronization Window.
- Added help for Turbo Mode in the Setup wizard.
V1.03
- Fixed issue of AP rebooting if 11a card is removed from
station or disassociates and then re-associates to the AP
- If the user does not change the client IP (STA IP) into
the same subnet, STA cannot get the IP of the AP using the
configuration utility
- The login page is case-sensitive in the web UI. Must enter
capital "A" for the username "Admin". The default password
is "5up".
V1.04
- Fixed DHCP Server issue
- Fixed login security issue in the web UI
- Fixed security issue with WEP key
V1.05
- Fixed javascript issue in web UI on the WEP encryption page
- Fixed html title tags on each page in the AP
V1.06
- Add POST feature to the Boot Code
- Added "Unique Key Table" for better WEP/ACL management
- Added "ACL Table" for better WEP/ACL management
- Added "Forgot Password" functionality. In the System section, Users
are given an option to answer a pre-defined question. If you
ever forget your password, you just need to answer that question in
order to find out your password.
V1.07
- Fixed grammar issues
---------------------------------------------------------------------
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.