1. RE990826.zip Driver
2. NDIS2.TXT File Contents

NDIS2.TXT Driver File Contents (RE990826.zip)

       ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»
       º                                                              º
       º       Compex RE100TX 10/100 PCI Fast Ethernet Adapter        º
       º        (C) Copyright PDS, 1999. All Rights Reserved.         º
       º                                                              º
       ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ

ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ GENERAL INFORMATION ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
 1) DOS and OS/2 NDIS v2.01 device driver
    RE100.DOS and RE100.OS2

     The NDIS drivers for OS/2 and DOS were written to and tested with
     the Network Driver Interface Specification (NDIS)
     Version 2.0.1.

** IMPORTANT:
   ========== 
  If you loading EMM386.EXE v4.49 ensure to exclude memory range D000-DFFF
    e.g. add this statement in Config.sys,
 
       Device=C:\DOS622\EMM386.EXE noems x=d000-dfff


 The file layout in the MSLANMAN.DOS and MSLANMAN>OS2 directories is
 shown below:-


  MSLANMAN.DOS
     ³
     ÀÄÄ DRIVERS
            ³
            ÃÄÄÄ ETHERNET
            ³       ³
            ³       ÀÄÄÄ RE100
            ³               ³
            ³               ÃÄÄ RE100.DOS
            ³               ÀÄÄ PROTOCOL.INI
            ³
            ÀÄÄÄ NIF
                  ³
                  ÀÄÄÄÄÄ RE100.NIF


  MSLANMAN.OS2
     ³
     ÀÄÄ DRIVERS
            ³
            ÃÄÄÄ ETHERNET
            ³       ³
            ³       ÀÄÄÄ RE100
            ³               ³
            ³               ÃÄÄ RE100.OS2
            ³               ÀÄÄ PROTOCOL.INI
            ³
            ÀÄÄÄ NIF
                  ³
                  ÀÄÄÄÄÄ RE100.NIF

ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ INSTALLATION GUIDE  ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
 1) LAN Manager 2.0
 ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ

     a) Start the SETUP program.

     b) Choose "Actions" from the top manual bar.

     c) Choose "Import network drivers" to load the driver.
        Insert the driver diskette into a drive and enter correct
        source drive letter. Then SETUP will create the appropriate
        directory and transfer the driver from the diskette.

	After this step, the driver is loaded.  If you want to change the
	existing driver, then you should go through the following steps:

     d) Choose "View/Modify" from the top manual bar.

     e) Press [ENTER] until you find the "Network Drivers"
        manual. In this manual, you will find the existing
        network driver configuration and all network adapters and
        protocols which it supports.

     f) Remove the existing configuration by choosing
        "Remove".

     g) Select "Compex RE100TX 10/100Base-TX PCI Ethernet Adapter" in the
        "Network adapter card" box and choose the appropriate protocol
        layer in the "Protocol" box.

     h) Choose "Add Driver" to add a hardware driver and "Add
        Protocol" to add a protocol driver to the "Network
        Configuration" box.

     i) Then choose "Done" to exit to the main manual. 

     j) Before exiting the SETUP program, choose "Save" from the
        "Actions" box to update the changes you have made.

 2) LAN Manager 2.1/2.2
 ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ

     The setup procedures for LAN Manager 2.1 is similar to LAN
     Manager 2.0.  Follow the procedure listed below to perform your
     installation.

     a) Start the SETUP program.

     b) Choose "Configuration" from the top manual bar.

     c) Choose "Network Drivers" to enter to the "Workstation
        Configuration" box.

     d) Choose "Add New Config" to check the existing network
        adapter drivers.

     e) Select "Other Driver" to import the driver from the
        diskette.

     Insert the driver diskette into a drive and enter correct 
     source drive letter. Then SETUP will create the appropriate 
     directory and transfer the driver from the diskette.



Parameters supported:

"*" indicate default value

  MEDIUM = AUTO
   Other option AUTO, 10HALF, 10FULL, 100HALF, 100FULL

 This parameter force the card to a specific media connect mode.
 Default is N-Way auto-negotiation

 
  NETADDRESS= xxxxxxxxxxxx
   where xxxxxxxxxxxx are hex numbers
   value in hex

 This parameter overrides the network address of the network
 adapter card.  The value of this parameter is a hexadecimal string of
 13 digits, as in @008048nnnnnn.  The address must be unique among
 all other network adapter addresses on the network."


  ETHERID = xxxxxxxxxxxx
   where xxxxxxxxxxxx are hex numbers
   value in hex

 This parameter using multiple network adapter card.
 The value of this parameter is a hexadecimal string of
 13 digits, as in @008048nnnnnn.  The address must be unique among
 all other network adapter addresses on the network."
 

   BUSNO = 0
    range is 0-31
    value in decimal

  This parameter is the PCI BUS number to combined this adapter card.
  The value of this parameter is 0-31"
  

   DEVICENO = 0
    range is 0-255
    value in decimal

 This parameter is the PCI DEVICE number to combined this adapter card.
 The value of this parameter is 0-255."

  TXFIFO = 0
   range is 0-63
   value in decimal

 Specifies the early transmit threshold level in the Tx FiFo begin the
 transmission.
 The value of this parameter is 0-63 "