ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º º º Compex FreedomLine 4-port 100TX/10Base-T PCI Adapter º º (C) Copyright PDS, 1997. All Rights Reserved. º º º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ 1. NetWare v4.x ODI Server Driver FL400.LAN v2.14 This Ethernet driver is for NetWare v4.x File Servers and complies to Novell ODI (Open Data-Link Interface) Specifications. 2. Installation Hardware and Software Requirements: A. Hardware Requirements: o An IBM-compatible personal computer with 80486 or higher microprocessor and PCI bus. o FreedomLINE 400TX/10base PCI Fast Ethernet Adapter (21140) Firmware Requirements: o PC BIOS with compliant Rev. 2.0 or higher PCI specifications. B. Software Revision Requirements: o NetWare version 4.xx. 3. Supplied Files: --------------------------------------------------------------------- NW4X.TXT This File --------------------------------------------------- FL400.LAN FL400 Novell NetWare ODI server driver. --------------------------------------------------- FL400.LDI Novell network installation file for this driver --------------------------------------------------- ETHERTSM.NLM Novell TSM needed to run the ODI server driver --------------------------------------------------- MSM.NLM Novell MSM needed to run the ODI server driver --------------------------------------------------- NBI.NLM Novell NBI needed to run the ODI server driver --------------------------------------------------------------------- Note:- If your NetWare server has not run the latest LOADER patch you will see this message: " Warning: This version of NetWare does not support protected mode BIOS access. Without this loader patch some PCI drivers may fail." Compex FreedomLine 4-port 100TX/10Base-T PCI Adapter does not require the loader patch. You can still apply the loader. In doing so, the above message will be supressed. This patch is provided in this disk. See readme files in the PATCH subdirectory on how to run the patch. 4. NetWare 4.10 enviroment ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Notes: ====== The MSM.NLM and ETHERTSM.NLM files that come with Novell Netware may not be the latest update NLMs to work properly with this LAN driver. When these NLMs were load from NetWare SYS:SYSTEM directory they can cause failure loading the FL400.LAN. To ensure that the correct NLMs loaded, users should copy the following files:- MSM.NLM, ETHERTSM.NLM, NBI.NLM, and FL400.LAN supplied in this diskette to the NetWare boot directory in local hard disk C:\NWSERVER. Then follow the steps as described below to load the NLMs and LAN driver. a) Run PCISNAP in Driver Disk 1 and select Driver Installation. b) From the Driver Installation Menu, choose Novell NetWare Driver and then select Install NetWare v4.x Server Driver. Change the destination path to C:\NWSERVER to copy the LAN driver and support files.. c) Follow the instruction on each screen to complete the installation. d) Run SERVER.EXE. e) At the NetWare prompt, run INSTALL.NLM by typing: : LOAD INSTALL <Enter> f) By default, press <Enter> to select "Driver Options". g) A "Driver Option" menu box will appear. Select "Configure network drivers" option and then press <Enter> key. h) In the "Additional Driver Actions" box, choose "Select a driver" option. Press <Insert> to load a LAN driver not listed. i) Press <F3> to specify the directory path of the LAN driver and press <Enter>: e.g. C:\NWSERVER <ÄÄÙ Enter " Fast Ethernet Driver" will be displayed. Press <Enter> to select the driver listed. j) Copy FL400.LAN, FL400.LDI, MSM.NLM, ETHERTSM.NLM and NBI.NLM into the system directory. k) A driver configuration option screen will be displayed. Select the appropriate options. To select the frame type you want to use, highlight "FL400_1 Protocols" box and press <F3>. Mark the frame type that you want to use and press <F10> to save the settings. l) After selecting the parameters, choose the "Save parameters and load driver" option to load the LAN driver. Press <ENTER> to use a given network number to bind ipx to the server driver. m) Press ESC to save and exit from the installation. 5. Netware 4.0x environment ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ a) Run PCISNAP in Driver Disk 1 diskette and select Driver Installation. b) From the Driver Installation Menu, choose Novell NetWare Driver and then select Install NetWare v4.x Server Driver. Change the destination path to C:\NWSERVER to copy the LAN driver and support files.. c) Follow the instruction on each screen to complete the installation. d) Run SERVER.EXE. e) At the NetWare prompt, run INSTALL.NLM by typing: : LOAD INSTALL <Enter> f) Select "Maintenance/Selective Install." g) Go to "LAN Driver Options." Press <Insert> to load a LAN driver not listed. h) Press <F3> to specify the directory path of the LAN driver and press <Enter>: e.g. C:\NWSERVER <ÄÄÙ Enter "Compex FreedomLine 4-port 100TX/10Base-T Fast Ethernet Driver" will display Press <Enter> to load the driver listed. i) Copy FL400.LAN, FL400.LDI, MSM.NLM, ETHERTSM.NLM and NBI.NLM into the system directory. j) A driver configuration options screen will be displayed. Select the appropriate options. k) Press <F10> to load the LAN driver. Press <ENTER> to use a given network number to bind ipx to the server driver. If you do not want to load all the frame types, press F3, from Frame Type mark only the frames you want to load. Otherwise, by default, NetWare loads all the frames. l) Press ESC to save and exit from the installation. 6. Parameters ÍÍÍÍÍÍÍÍÍÍ The following parameters belong on the server's command line, or in the load line inside the AUTOEXEC.NCF. The general way of using these parameters is: LOAD <driver name> <PARAMETER NAME>... <PARAMETER NAME[=VALUE]> Example: LOAD FL400 TURBO SLOT=10001 FRAME=Ethernet_802.3 Driver specific parameters list (as for NetWare standard parameters, please see the NetWare user's manual): TP selects TP port. (*) AUTODETECT enables autodetection of media type when driver is loading. Note that this ONLY! works at initialization time, i.e. when the driver first loads for a specific network card. TP_NO_LINK_TEST selects twisted pair connection, but disables the LINK test for specific HUBs that do not support LINK. TP_FULL_DUPLEX selects twisted pair connection to work in full duplex mode. TURBO Fixes the problem of multiple transmit underflows and receive overflows (i.e. lose of packets) in systems that use certain PCI chipsets. SKIP_CHECK_BIOS Skip checking compatibility of PCI BIOS (**) LINE_SPEED selects line speed between 10MPBs and 100MBPs on network cards based on 100TX cards. Format: LINE_SPEED=<value> Allowed values are: 10,100 Notes: ------ (*) Those keywords affect ONLY ENET32-PCI and FreedomLINE32-PCI adapters. (**) Those keywords affect ONLY FreedomLINE 4-port 100TX/10Base-T PCI adapter.Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.