3Com (R) Corporation
EtherDisk (R) Diskette for
the Fast EtherLink and the EtherLink III (R) Bus master Adapters
Configuration and Diagnostic Program Instructions Summary
Overview
--------
The configuration portion of the program allows you to change the
configuration parameters for the adapter to fit the specific
environment in which the adapter is installed.
The diagnostic portion of the Configuration and Diagnostic Program
is designed to make sure that the adapter is installed correctly and
functioning properly in your computer. The Group 1 tests check the
physical components, connectors, and circuitry of the adapter and
require only that the adapter be installed in the computer. The
Group 2 tests check the adapter's ability to transmit data on the
network and require that the adapter be connected to a loopback plug
or to a network. The Group 3 tests check the adapter's ability to
correctly transmit and receive data over the network and require
that the adapter be connected to a network on which an echo server
has been set up.
The computer containing the adapter to be configured or tested must be
running DOS only.
NOTE: If this computer is an operating server, notify all users of the
server to save their work and log out from the network. The
Configuration and Diagnostic Program disrupts the normal operation
of servers and workstations, so work that is not saved may be lost.
Then shut down the server, and reboot with a DOS-only diskette.
(This way no drivers or TSRs will be running when the program
is started.)
Starting the Configuration and Diagnostic Program
--------------------------------------------------
There are two ways to start the program:
* Automatically, from the INSTALL.EXE program, by selecting the options
in the Configuration and Diagnostic submenu.
* Manually, from the root directory of the EtherDisk diskette, by typing
the following command:
3C59XCFG [command keyword] [parameter list]
3C59XCFG represents the 3Com Configuration and Diagnostic Program name.
The brackets indicate that the command keyword and parameter list are
optional.
3C59XCFG without any arguments invokes the program in full windows mode.
This includes mouse support and context-sensitive help. Press [F1] for
help at any time.
Command Line Keywords:
----------------------
You can use the first two characters of any command or parameter
as a shortcut. For example, 3C59XCFG HE RU means 3C59XCFG HELP RUN.
Also, the command keywords and parameters are not case-sensitive,
so CONFIGURE, configure, and Configure, for example, will all work.
CONFIGURE - Configures an adapter in one of three ways.
(1) automatically with /auto parameter
(2) using a specified adapter configuration file
(3) using command line configuration parameters
ECHOSERVER - Enables a designated adapter to function within the echo
server.
HELP - Displays general or command-specific help information. To get
command-specific help, enter:
3C59XCFG HELP [command keyword]
LANGUAGE - Invokes the program in full windows mode using a specified
external resource file. This option provides support for
multiple languages via a different resource file for each
language supported.
LIST - Displays a list of installed adapters recognized by this program
and their assigned adapter numbers.
RUN - Executes the diagnostic tests (which can also be specified from a
file) on a selected adapter and writes the results to the screen,
a file, or a printer.
Configuration
-------------
The adapter can be configured in one of the following four ways, which
are described in greater detail below:
* Full Screen Windows Mode
* Command Line with Auto Configuration
* Command Line with Explicit Parameters
* Command Line with Configuration File
Full screen windows mode
------------------------
To configure the adapter using the full screen windowing, type 3C59XCFG
and [Enter]. Then select the Configure Adapter option in the Install
pull-down menu.
Command line options
--------------------
Defaults: CONFIGURE has /AUTO and /ADAPTERNUM:1 as defaults. So for
example, if only "3c59xcfg configure" is used, adapter number 1 will be
auto configured.
ADAPTERNUM:N and /SLOT:S parameters can be used with any of the CONFIGURE
options that follow. They are both intended for use whenever multiple
adapters are present in the computer and recognized by the Configuration
and Diagnostic Program.
/ADAPTERNUM:N specifies the adapter number to be configured for PCI and
and EISA computers. Run the LIST command separately to determine the
adapter number to use here.
/SLOT:S specifies the physical slot number of the adapter to be configured
in EISA computers.
Command Line with Auto Configuration
------------------------------------
Command syntax: 3C59XCFG CONFIGURE /AUTO
The /AUTO parameter configures the adapter automatically select media
type. All other option settings are left unchanged.
NOTE: The program will attempt to detect what media type is being
used, to set the media type. Therefore connect to the network
first, then run /AUTO, and it will configure the media type for you.
Command Line with Explicit Parameters
-------------------------------------
Command syntax: 3C59XCFG CONFIGURE [ /BSIZE:N /XCVR:N /TR:N
/FULLDUPLEX:N /OPTIMIZE:N /LINKBEAT:N ]
Command line configuration parameters are used to configure the adapter
using only the option settings you specify. Some parameters are for
all adapters, some are for PCI only. For example, /BSIZE:N is an
PCI-only parameter, because with EISA adapters, the computer vendor's
configuration utility or the opttion diskette handles the setting of
the Boot PROM size. In most cases, any combination of parameters can
be used. Therefore it is possible to modify only a few settings if
needed.
/BSIZE - Boot PROM Size (PCI only)
Possible values - 8,16,32,64,disabled
/TR (or /XCVR) - Transceiver (PCI only)
Possible values - 100BASE-TX, TP, 10BASE-T (same as TP), COAX,
AUI, EXTERNAL (same as AUI)
/OPTIMIZE - Network Driver Optimization
Possible values - NORMAL, NETWORK, CPU
/LINKBEAT - Link beat disable/enable (pre-10BASE-T standard only)
Possible values - disabled, enabled
NOTE: Try this setting ONLY if pre-10BASE-T standard hubs
are in use.
/FULLDUPLEX - Full Duplex disable/enable (For 10Base-T only)
Possible values - disabled, enabled
NOTE: Enable this setting ONLY when the adapter is connected
to a 10BASE-T repeater supporting full duplex.
Otherwise, it will bring down the network.
Command Line with Configuration File
------------------------------------
Command syntax: 3C59XCFG CONFIGURE /CONFIGFILE:filename
/CONFIGFILE:filename is used to configure an adapter with the settings
specified in an ASCII configuration file that can be created and modified
by any text editor. The filename can be a fully qualified DOS filename
including a path. A standard format for the file must be used, as
follows:
- Variable names and values match the wording in the full-screen
configure window in most cases.
- Begin each variable/value line with an "at" symbol (@), followed by
a variable name, a colon (:), and the value.
Example: @Media type: 100BASE-TX
- Blank lines and other white spaces are allowed between variable
lines.
- Start any comment lines with a semicolon (;).
- The variable names allowed are:
Boot PROM size
Media type
Network driver optimization
Full Duplex
Link beat
- The values allowed are the same as those shown in the full-screen
configure window.
Example 1: @Network driver optimization:Normal
Example 2: @Media type:On-board Coax
Diagnostic
----------
* Full screen windows mode
To run the diagnostic tests using the full screen windowing, type
"3C59XCFG" and ENTER. Then select the Run Tests option in the Tests
pull-down menu.
* Command line option - "Run"
Command syntax: 3C59XCFG RUN [/TESTFILE:filename] [/RESULTS:[filename
| PRN | PRNHP]] [/ADAPTERNUM:N | /SLOT:S]
The RUN parameter executes the diagnostic tests on a selected adapter
and displays the results on the screen. The defaults are adapter number 1
and Group 1 tests. The parameters below are all optional.
/TESTFILE:filename specifies a test file that contains a specific test
setup description.
/RESULTS:[filename or PRN or PRNHP] specifies an alternative location to
store the test results. This location can be a DOS path and filename,
PRN printer port (same as LPT1), or PRNHP, which is an HP LaserJet printer
connected to LPT1.
/ADAPTERNUM:N specifies the adapter number to be tested, in the case of
multiple adapters installed in the computer and recognized by this
program. Run the LIST command separately (see LIST below) to determine
the adapter number to use.
/SLOT:S specifies the physical slot number of the adapter to be tested
when multiple adapters are installed in EISA computers.
Other Command Line Options
--------------------------
* HELP
Command syntax: 3C59XCFG HELP [Command Keyword]
HELP is an on-line summary of commands. Without a command keyword,
it gives a summary of the command keywords. With a command keyword
specified, it gives the parameter choices for that particular command.
For example, "3C59XCFG HELP CONFIGURE" gives details about the parameter
options for the CONFIGURE command.
* LANGUAGE
Command syntax: 3C59XCFG LANGUAGE /LANGFILE:filename
LANGUAGE invokes the program in full windows mode using a specified
external resource file. This option provides support for multiple
languages via a different resource file for each language supported.
/LANGFILE:filename is a required parameter with this command.
The filename is the name of the resource file that is loaded by the
program. The filename can be a fully qualified DOS filename.
NOTE: At this time, there are no alternate resource files included on
the EtherDisk diskette.
* LIST
Command syntax: 3C59XCFG LIST
LIST displays a list of currently installed adapters (and their assigned
adapter numbers) that are recognized by this program. The adapter number
is then used as the N value for the /ADAPTERNUM:N parameter when multiple
adapters are installed. There are no parameters associated with the LIST
command keyword.
* ECHOSERVER
Command syntax: 3C59XCFG ECHOSERVER [/ADAPTERNUM:N | /SLOT:S]
ECHOSERVER enables an adapter to function within an echo server.
/ADAPTERNUM:N specifies the adapter number to be configured in the echo
server, in the case of multiple adapters. /SLOT:S is available only on
EISA computers, and refers to the physical slot in the echo server
where the adapter is located.
Further Assistance
------------------
If the adapter fails any of the diagnostic tests, see the TROUBLE.TXT file
in the \DIAG directory on the EtherDisk diskette for troubleshooting
procedures.
The SUPPORT.TXT file in the \INFO subdirectory on the EtherDisk diskette
provides information about obtaining product support for the adapter.
3Com, EtherDisk, and EtherLink are registered trademarks of 3Com Corporation.
All other trademarks are the property of their respective owners.
(%VER Configuration and Diagnostic Program Instructions Summary v1.0b)
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.